MON192CL10 en Instruction Manual_en
AutoDome, Bilinx, Bosch, the Bosch logo, DiBos, FastAddress and VIDOS are registered trademarks of Bosch Security Systems, inc. The following trademarks are registered with the United States Patent and Trademark Office: Pentium is a registered trademark of Intel Corporation .
Safety Precautions | en Important Safeguards 1. Read, Follow, and Retain Instructions - All safety and operating instructions should be read and followed before operating the unit. Retain instructions for future reference. 2. Heed Warnings - Adhere to all warnings on the unit and in the operating instructions. 3. Attachments - Attachments not recommended by the product manufacturer should not be used, as they may cause hazards. 4.
iv en | Safety Precautions For Indoor Product Safety Precautions 1. Water and Moisture - Do not use this unit near water for example, in a wet basement, in an unprotected outdoor installation or in any area classified as a wet location. 2. Object and Liquid Entry - Never push objects of any kind into this unit through openings, as they might touch dangerous voltage points or create short circuits, resulting in a fire or electrical shock. Never spill liquid of any kind on the unit.
Safety Precautions | en v FCC & ICES INFORMATION (U.S.A. and Canadian Models Only) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
vi en | MON192CL10 Preface This guide describes how to install the MON192CL10 monitor. Audience This guide is intended for qualified installation and service personnel who are familiar with the applicable national and local electrical codes. Document Conventions Convention Bold Italic Underline courier Meaning Denotes a part, item, or assembly. Denotes a reference to another paragraph, figure or table. Used to emphasize a point.
MON192CL10 | en vii Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers USA Phone: 800-366-2283 or 585-340-4162 Fax: 800-366-1329 Email: cctv.repair@us.bosch.com Technical Support Phone: 800-326-1450 Email: technical.support@us.bosch.com CCTV Spare Parts Phone: 800-894-5215 or 408-957-3065 Fax: 408-935-5938 Email: BoschCCTVparts@ca.slr.
viii en | F01U032133 | 1.0 | 2007.03 MON192CL10 Instruction Manual Bosch Security Systems, Inc.
MON192CL10 Table of Contents | en ix Table of Contents 1 Unpacking 1 1.1 Parts List 1 2 Exploded View 2 3 Description 4 3.1 Features 4 3.2 Power 4 4 Installing the MON192CL10 5 4.1 Mounting the MON192CL10 5 4.1.1 Desktop Installation 5 4.1.2 Wall Mount Installation 5 4.1.3 Extension Cable Installation 7 4.2 Connecting the Composite Video Signal to the Monitor 8 4.3 Connecting the Y/C (S-Video) Signal to the Monitor 8 4.4 Connecting Audio to the Monitor 8 4.
x en | Table of Contents MON192CL10 7 On-screen Display Menu Reference 22 8 Maintenance 28 9 Specifications 29 F01U032133 | 1.0 | 2007.03 Instruction Manual Bosch Security Systems, Inc.
MON192CL10 1 Unpacking | en 1 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
2 2 en | Exploded View MON192CL10 Exploded View Fig. 2.
MON192CL10 Exploded View | en Fig. 2.2 3 Back Panel MON192CL10 Reference Button 1 Power input connector from base or optional power supply 2 DVI-I connector 3 PC audio input The base unit contains the main connectors that supply power to the monitor. Fig. 2.3 Base MON192CL10 Reference Button 1 Power supply connector to display 2 Power supply On/Off 3 Power cord connection Bosch Security Systems, Inc. Instruction Manual F01U032133 | 1.0 | 2007.
4 3 en | Description MON192CL10 Description The MON192CL10 19-inch (48-cm) Color Panel Display Monitor displays PAL or NTSC standard color pictures in CCTV systems. The MON192CL10 monitor includes two (2) looping Composite Video BNC connector inputs, two (2) looping Audio RCA inputs, and two (2) looping Y/C (S-Video) input using a 4-pin mini-DIN. In addition, this model works with both DVI-I and VGA signals.
MON192CL10 4 Installing the MON192CL10 | en 5 Installing the MON192CL10 This chapter outlines the procedures needed to install the MON192CL10 Series. Installation should be made by a qualified service person and all local codes should be conformed to. 4.1 Mounting the MON192CL10 The MON192CL10 is designed to be used for desktop, wall, or rack mounting. 4.1.1 Desktop Installation The MON192CL10 monitor is delivered with a 3-pole US-style power cord and a 3-pole Eurostyle power cord.
6 en | Installing the MON192CL10 2. MON192CL10 Remove the power bayonet connector from the panel (see Figure 4.2 on page 6), while sliding the base off the monitor. Fig. 4.2 Removing the Power Bayonet 3. Mount the unit to the mounting device (not provided) using the four (4) mounting holes on the rear panel. The square mounting hole patterns are standard on 100 mm (3.9 in.) centers, as shown in Figure 4.3 on page 6. Fig. 4.3 Mounting the Device F01U032133 | 1.0 | 2007.
MON192CL10 4.1.3 Installing the MON192CL10 | en 7 Extension Cable Installation Use the Extension Cable (included with the MON192CL10) to place the power supply/base unit up to 1.5 m (5 ft) from the LCD panel for wall mount or rack mount installations. 1. Follow the instructions in Section 4.1.2: Wall Mount Installation to remove the power supply/base from the LCD panel section. 2.
8 en | Installing the MON192CL10 4.2 MON192CL10 Connecting the Composite Video Signal to the Monitor There are two (2) BNC connectors located on the rear of the monitor for composite video input and two (2) BNC connectors for composite video outputs (Figure 2.2 on page 3). NOTE: All video inputs are active loop-through. The impedance is automatically set to 75 ohm by the input of the signal on the input connector, while operating in a single connection mode (Figure 4.12 on page 12).
MON192CL10 4.5 Installing the MON192CL10 | en 9 Connecting the PC Audio to the Monitor There is one (1) audio input for the PC (see Figure 4.8 on page 9); for use with the supplied Mini Phone Jack Audio Cable. The audio input is designed to accept line level audio, 1 V peak to peak. 4.
10 en | Installing the MON192CL10 4.7.2 MON192CL10 DVI to DVI If the source has a DVI-I or DVI-D connector, use the DVI-D to DVI-D cable provided. Fig. 4.10 DVI-I to either DVI-D or DVI-I Reference # Description 1 MON192CL10 DVI-I Female Connector 2, 3 DVI-D Male to DVI-D Male Cable 4, 5 Source DVI-D Female or DVI-I Female Connector F01U032133 | 1.0 | 2007.03 Instruction Manual Bosch Security Systems, Inc.
MON192CL10 4.7.3 Installing the MON192CL10 | en 11 Using a Quad Output Adapter / DMS-59 Connection A quad output adapter (not supplied) can be used to connect up to four LCD monitors. The best connection would require a DMS to DVI splitter cable for two (2) monitors or two (2) splitter cables to support up to four (4) monitors. The cables used should be the ones recommended by the manufacturer of the graphics card along with the DVI-D to DVI-D cable included. Fig. 4.
12 4.8 en | Installing the MON192CL10 MON192CL10 Ventilation To prevent overheating, ensure that the ventilation openings on the rear of the monitor are not covered. 4.9 Single / Multiple Monitor Configuration Fig. 4.12 Single Monitor Configuration Fig. 4.13 Multiple Monitor Configuration F01U032133 | 1.0 | 2007.03 Instruction Manual Bosch Security Systems, Inc.
MON192CL10 Navigating the Monitor | en 5 Navigating the Monitor 5.1 Navigating the Front Panel 13 Use the front panel to make any necessary OSD adjustments to the MON192CL10. To navigate the set up menus, see Figure 5.1 on page 13. Fig. 5.
14 5.3 en | Navigating the Monitor MON192CL10 Navigating the Monitor On-screen Display (OSD) The MON192CL10 has two (2) modes, Video and VGA. The MON192CL10 is programmed through the on-screen display (OSD) menus. Each on-screen display (OSD) shows a list of parameters or submenus that can be selected by the operator. To access the OSD menus, press the Menu button. Use the front panel of the MON192CL10 to make any necessary adjustments to the OSD. To navigate the set up menus, follow the steps below: 1.
MON192CL10 5.4 Navigating the Monitor | en 15 On-screen Display Menus There are ten (10) on-screen main menus which allow you to customize your settings. Press the Menu button to access the OSD menu. Icon Menu Function Tint Adjusts the contrast and brightness of the OSD. NOTE: Applicable to NTSC only, not available in PAL format. Color Adjusts the overall intensity of the screen. Sharpness Adjusts the sharpness level for video performance (range 0-100).
16 5.5 en | Navigating the Monitor MON192CL10 Video Mode X To access the OSD video mode, press the Menu button. The following is displayed: TINT COLOR SHARPNESS DEFAULT LANGUAGE Channel Title UNDERSCAN DISABLE 3D COMB FILTER DISABLE PIP MENU POWER-ON OPTIONS INPUT ENABLE/DISABLE VOLUME EXIT Fig. 5.2 Video Mode OSD Menu Default Function Setting Tint 50 Adjusts tint level; for best results, adjust until skin color is natural (range 0-100).
MON192CL10 Navigating the Monitor | en 17 Enables or disables the input selections. Input Enable/Disable NOTE: To disable switching to inputs that are not connected, Disable the unused Input in this menu. Example: Only VIDEO 1 and the DVI-I are connected S-Video and Video 2 are not connected and are disabled. Press INPUT to scroll from VIDEO 1 to PC, then back to VIDEO 1 again. Volume 50 Exit 5.6 Adjusts the volume for the audio inputs (range 0-100).
18 en | Special Features MON192CL10 Input All Enables or disables the input selections. Enable/Dis- enabled NOTE: To disable switching to inputs that are not connected, Disable the unused Input in this menu. able Example: Only VIDEO 1 and the DVI-I are connected S-Video and VIDEO 2 are not connected and are disabled. Press INPUT to scroll form VIDEO 1 to PC, then back to VIDEO 1 again. 6 Information Displays information about the type of connection.
MON192CL10 Special Features | en 6.2 19 PIP Menu (Video and VGA) To enhance the multi-input capability, "Picture-in-Picture" allows any of the composite video or S-Video inputs to be inserted into each other, or into the VGA/DVI display.
20 en | Special Features 6.2.2 MON192CL10 PIP Location PIP MENU PIP LOCATION PIP INPUT PIP LOCATION PIP SIZE PIP PAP HV KEYSTONE TOP LEFT TOP RIGHT BOTTOM RIGHT BOTTOM LEFT PIP H. POSITION PIP V. POSITION DISABLE DISABLE EXIT EXIT Submenu 6.2.3 Default Setting Definition PIP H. Position Adjusts the horizontal position (1-7) PIP V.
MON192CL10 Special Features | en 6.3 Display Setting Menu 21 (VGA) AUTO SET DISPLAY SETTING DISPLAY SETTING H. POSITION COLOR TEMPERATURE V. POSITION LANGUAGE FINE TUNE VOLUME EXIT DEFAULT PIP MENU POWER-ON OPTIONS INPUT ENABLE/DISABLE INFORMATION EXIT Submenu Default Setting Definition H. Position * Adjusts the horizontal position (0-400) V.
22 7 en | On-screen Display Menu Reference MON192CL10 On-screen Display Menu Reference This chapter outlines the menus for the Video and VGA mode (NTSC only) for the MON192CL10 Series. F01U032133 | 1.0 | 2007.03 Instruction Manual Bosch Security Systems, Inc.
MON192CL10 Bosch Security Systems, Inc. On-screen Display Menu Reference | en Instruction Manual 23 F01U032133 | 1.0 | 2007.
24 en | On-screen Display Menu Reference F01U032133 | 1.0 | 2007.03 MON192CL10 Instruction Manual Bosch Security Systems, Inc.
MON192CL10 On-screen Display Menu Reference | en 25 VGA Mode Bosch Security Systems, Inc. Instruction Manual F01U032133 | 1.0 | 2007.
26 en | On-screen Display Menu Reference F01U032133 | 1.0 | 2007.03 MON192CL10 Instruction Manual Bosch Security Systems, Inc.
MON192CL10 On-screen Display Menu Reference | en 27 The error message “PC Out of Range” is displayed in the VGA/DVI mode if the PC is operating with either a resolution or timing mode that is not supported by the MON192CL. Change the PC settings to one of the valid combinations below: VGA / DVI Timing Modes: 640 x 480 60/72/75 Hz 800 x 600 60/72/75 Hz 1024 x 768 60/70/75 Hz 1280 x 1024 60/75 Hz Note: 640 x 480 is not supported in DVI operation. Bosch Security Systems, Inc.
28 8 en | Maintenance MON192CL10 Maintenance To clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or a soft lint-free cloth. Staining and discoloration may occur if left on the panel for long periods. If the surface (polarizer) of the LCD panel is dirty or stained, use absorbent cotton or a soft lint-free cloth to remove the residue as follows: 1. Turn off the computer or display. 2. Do not spray any liquid directly on the screen.
MON192CL10 9 Specifications | en 29 Specifications Bosch Security Systems, Inc. Instruction Manual F01U032133 | 1.0 | 2007.
Americas: Bosch Security Systems 130 Perinton Parkway Fairport, New York, 14450 USA Phone +1 800 289 0096 Fax +1 585 223 9180 www.boschsecurity.us Europe, Middle East, Asia: Bosch Security Systems B.V. Postbus 80002 5600 JB Eindhoven Phone: +31 40 2577 200 Fax: +31 40 2577 202 nl.securitysystems@bosch.com www.boschsecurity.nl www.boschsecurity.com © Bosch Security Systems, Inc., 2007; F01U032133 | 1.0 | 2007.03 www.boschsecurity.com Asia-Pacific: Bosch Security Systems Pte Ltd.