FlexiDomeHD 1080p IP Camera NDN-832 en Installation Manual
FlexiDomeHD 1080p IP Camera Table of Contents | en 3 Table of Contents 1 Safety 6 1.1 Safety precautions 6 1.2 Important safety instructions 7 1.3 Connection in applications 8 1.4 Type label 8 1.5 FCC & ICES compliance 1.6 MicroSD cards 10 9 1.7 UL certification 10 1.8 Bosch notices 11 1.9 Copyrights 12 2 Introduction 13 2.1 Features 13 3 System Information 14 3.1 Overview of functions 14 3.1.1 Progressive scan 14 3.1.2 Day/Night function 14 3.1.
en | Table of Contents FlexiDomeHD 1080p IP Camera 5 Installation 19 5.1 Parts 19 5.2 Mounting the unit 20 5.2.1 Surface mounting 20 5.2.2 Flush mount 22 5.3 Connections 24 5.3.1 Make the connections 24 5.4 Mount the camera module 27 5.5 Opening the camera module 28 5.6 Controls 29 5.7 Camera set-up 30 5.8 Camera positioning 31 5.8.1 Pan 31 5.8.2 Tilt 32 5.8.3 Twist 33 5.9 Using the install wizard 34 5.9.1 Adjustment procedure 34 5.
FlexiDomeHD 1080p IP Camera Table of Contents | en 5 10 Technical Data 45 10.1 Specifications 45 10.1.1 Dimensions 47 Bosch Security Systems Installation Manual AM18-Q0601 | v1.0 | 2012.
en | Safety FlexiDomeHD 1080p IP Camera 1 Safety 1.1 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation.
FlexiDomeHD 1080p IP Camera 1.2 Safety | en 7 Important safety instructions Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings on the unit and in the operating instructions before operating the unit. 1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners. 2. Do not install unit near any heat sources such as radiators, heaters, stoves, or other equipment that produce heat.
en | Safety 1.3 FlexiDomeHD 1080p IP Camera Connection in applications Grounding The yellow/green safety (power) ground wire from the camera must be connected to the system earth of the installation. U.S.A.: - section 810 of the National Electrical Code, ANSI/NFPA No.70, provides information regarding proper grounding. 12 VDC / 24 VAC power source: This unit is intended to operate with a limited power source. The unit is intended to operate at either 12 VDC or 24 VAC (if PoE is not available).
FlexiDomeHD 1080p IP Camera 1.5 Safety | en 9 FCC & ICES compliance FCC & ICES Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
en | Safety 1.6 FlexiDomeHD 1080p IP Camera MicroSD cards Bosch Security systems recommends that local storage on microSD card should only be used for alarm recording and Automatic Network Replenishment (ANR) applications. To minimize the risk of lost of digital information, we recommend multiple, redundant recording systems, and a procedure to back up all digital information. 1.7 UL certification Disclaimer Underwriter Laboratories Inc.
FlexiDomeHD 1080p IP Camera 1.8 Safety | en 11 Bosch notices Video loss Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information.
en | Safety 1.9 FlexiDomeHD 1080p IP Camera Copyrights The firmware uses the fonts "Adobe-Helvetica-Bold-R-Normal-24-240-75-75-P-138-ISO10646-1" and "Adobe-Helvetica-Bold-RNormal--12-120-75-75-P-70-ISO10646-1" under the following copyright: Copyright 1984-1989, 1994 Adobe Systems Incorporated. Copyright 1988, 1994 Digital Equipment Corporation.
FlexiDomeHD 1080p IP Camera Introduction | en 2 Introduction 2.1 Features 13 The FlexiDomeHD 1080p IP Day/Night camera is a highperformance, surveillance color camera. The camera uses H.264 compression technology to give clear images while reducing bandwidth and storage requirements. It is also ONVIF compliant to improve compatibility during system integration.
en | System Information FlexiDomeHD 1080p IP Camera 3 System Information 3.1 Overview of functions The camera incorporates a network video server. Its primary function is to encode video and control data for transmission over an IP network. With its H.264 encoding, it is ideally suited for IP communication and for remote access to digital video recorders and IP systems. The use of existing networks means that integration with CCTV systems or local networks can be achieved quickly and easily.
FlexiDomeHD 1080p IP Camera System Information | en 15 ONVIF standard is a global standard for the interface of network video products. 3.1.5 Audio Two-way duplex audio is available in the unit for live voice communications or audio recording. 3.1.6 Alarm I/O The alarm input can be used to control the functionality of the unit. An alarm output can control external devices. 3.1.
en | System Information 3.1.12 FlexiDomeHD 1080p IP Camera Encryption The unit offers a variety of options for protection against unauthorized reading. Web browser connections can be protected using HTTPS. Protect the control channels via the SSL encryption protocol. With an additional license, the user data itself can be encrypted. 3.1.
FlexiDomeHD 1080p IP Camera 3.2 System Information | en 17 Operation with external systems The camera can be used with a variety of Bosch systems: – Bosch Video Management System – Bosch Video Client – Bosch Recording Station When connected to any of these systems, many of the camera configuration parameters are controlled by the system and not by the settings made via a web browser.
en | Planning FlexiDomeHD 1080p IP Camera 4 Planning 4.1 Unpacking Unpack carefully and handle the equipment with care.
FlexiDomeHD 1080p IP Camera 5 Installation | en 19 Installation CAUTION! Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. 5.1 Parts The camera/housing unit consists of the following parts: 1. 2. 3. Bosch Security Systems Mounting base Surface mount ring Camera module with fixing ring Installation Manual AM18-Q0601 | v1.0 | 2012.
en | Installation FlexiDomeHD 1080p IP Camera 5.2 Mounting the unit 5.2.1 Surface mounting 9.5 mm (0.375 in) Ø 8 m m 3x 3x PCD 123 mm (4.84 in) Figure?5.1?Surface mounting To mount the camera on the surface of a wall or ceiling: 1. Use the mounting base as a template to mark the holes indicated in the drawing. The PCD is 123 mm (4.84 in). 2. Drill three holes with a diameter of 8 mm (0.3 in). 3. Insert the supplied plugs into the holes. 4.
FlexiDomeHD 1080p IP Camera Installation | en 21 5. Place the surface mount ring over the cable tree. 6. Suspend the camera module from the plastic hook inside the mounting base ensuring that the suspension cable is seated securely in the groove. Bosch Security Systems Installation Manual AM18-Q0601 | v1.0 | 2012.
en | Installation 5.2.2 FlexiDomeHD 1080p IP Camera Flush mount 156 mm (6.14 in) Ø 8 m m 3x 3x PCD 178 mm (7 in) Figure?5.2?Flush mounting To flush mount the camera in a wall or ceiling: 1. Use the mounting base as a template to mark out the recess and to mark the holes indicated in the drawing. The PCD is 178 mm (7 in) 2. Cut out the recess. 3. Drill three holes with a diameter of 8 mm (0.3 in). 4. Insert the supplied plugs into the holes. 5.
FlexiDomeHD 1080p IP Camera 6. Installation | en 23 Suspend the camera module from the plastic hook inside the mounting base. Bosch Security Systems Installation Manual AM18-Q0601 | v1.0 | 2012.
en | Installation 5.3 5.3.1 FlexiDomeHD 1080p IP Camera Connections Make the connections The unit has connection terminals on flying leads. In wet or outdoor installations make use of a field wiring box with NEMA Type 4X or IP66 protection level or better. Make the connections inside a water tight compartment. After connections are made ensure that the watertight compartment is tightly closed and cables and conduits are properly sealed to prevent ingress of water.
FlexiDomeHD 1080p IP Camera Installation | en 25 CAUTION! Check the type label on the rear of the camera module for the correct power ratings. Power connection 1. 2. Use a class 2 power supply 24 VAC or +12 VDC. Connect the power wires (red+ , brown-) to the power supply. 3. Connect the earth wire (yellow/green) from the camera to the system earth of the installation to ensure correct EMC/ RFI and safety protection. Network (and PoE) connection 1.
en | Installation FlexiDomeHD 1080p IP Camera contact can be used as the actuator (use a bounce-free contact system). – Refer to the cable tree table to identify the wire colors for – Configurable as active low or active high. connecting the alarm input. Alarm output Use the alarm relay output for switching external devices such as lamps or sirens. – Refer to the cable tree table to identify the wire colors for connecting the alarm output.
FlexiDomeHD 1080p IP Camera 5.4 Installation | en 27 Mount the camera module 1. Route the cable tree from the camera around the rear of the camera module and secure all cables. 2. For surface mounted units, place the surface mount ring over the mounting base. – With a side connection, remove the tab at the side entrance; with a rear connection, leave it in place. 3.
en | Installation 5.5 FlexiDomeHD 1080p IP Camera Opening the camera module 1. Using the supplied screwdriver bit, loosen the two screws securing the camera window section of the camera module. 2. Carefully, allow the camera window section to hang loose on the earth wire. x2 AM18-Q0601 | v1.0 | 2012.
FlexiDomeHD 1080p IP Camera 5.6 Installation | en 29 Controls 1. Indication LEDs The bi-colored LED indicates a failure (red), normal operation (green) or an established connection (green flashing). It can be disabled in the installer menu. 2. Menu button The menu button is used to start the installation wizard. 3. Reset button Restores the default IP address or restores a previous version of the firmware if uploading a new version fails.
en | Installation 5.7 FlexiDomeHD 1080p IP Camera Camera set-up To help set up the camera for installation: 1. Connect a monitor to the 2.5 mm jack using the optional monitor cable (S1460) which provides a CVBS signal (for installation purposes only). 2. Disconnect the internal network cable. 3. Connect an external network cable with power (PoE). 4. After power-up, wait a little (less than 20 seconds). 5. Press the menu button.
FlexiDomeHD 1080p IP Camera 5.8 Installation | en 31 Camera positioning The camera module position can be adjusted along three axes. CAUTION! Do not expose the sensors to direct sunlight. 5.8.1 Pan For horizontal adjustment (pan): 1. Slightly loosen the three screws in the fixing ring with the supplied screwdriver bit. 2. Rotate the camera module in the base. Do not rotate more than 180° in either direction. 3. Tighten the three screws in the fixing ring with the supplied screwdriver bit.
en | Installation 5.8.2 FlexiDomeHD 1080p IP Camera Tilt For vertical adjustment (tilt): 1. Loosen the two screws in the camera module wings with the supplied screwdriver bit (1). 2. Swing the camera module between the wings. Do not rotate more than 100°. 3. Tighten the two screws in the camera module wings with the supplied screwdriver bit (1). 4. For extra secure locking, tighten (hand-tight) the two socket head screws in the side of the camera module wings with the supplied allen key (2).
FlexiDomeHD 1080p IP Camera 5.8.3 Installation | en 33 Twist To obtain a horizontal horizon (for tilted ceilings or sidewall mounting), push and turn the green lever as necessary to align the picture shown on the monitor. Bosch Security Systems Installation Manual AM18-Q0601 | v1.0 | 2012.
en | Installation 5.9 FlexiDomeHD 1080p IP Camera Using the install wizard The Menu button on the control panel is used to access the camera install wizard. When there is a choice in the wizard, the options are selected by either a short press or a longer press of the button. The wizard handles the following functions: – Lens identification – Zoom and focus adjustment conditions – Image orientation – Auto back focus Run the wizard to adjust the focus.
FlexiDomeHD 1080p IP Camera 4. Installation | en 35 Briefly press the Menu button to start the automatic motorized back focus (Auto MBF) adjustment. – You will hear the motorised automatic back focus process running. – 5. The progress is shown on the monitor. If the camera is not correctly focussed, press the Menu button for a longer time to restart the wizard. 6. If the camera is correctly focussed, briefly press the Menu button to save the results. 5.10 – The back focus position is stored.
en | Camera configuration 6 FlexiDomeHD 1080p IP Camera Camera configuration The camera normally provides an optimal picture without the need for further adjustments. Configuration of the camera is carried out via the network using a web browser. 6.1 Day/Night switching The camera is equipped with a motorized IR filter. The mechanical IR filter is taken out of the optical path in low-light applications.
FlexiDomeHD 1080p IP Camera 7 Browser connection | en 37 Browser connection A computer with Microsoft Internet Explorer can be used to receive live images from the camera, control the camera, and replay stored sequences. The camera is configured over the network using the browser. The configuration options using the menu system of the camera itself are limited to setting up the lens and network.
en | Troubleshooting FlexiDomeHD 1080p IP Camera 8 Troubleshooting 8.1 Function test The camera offers a variety of configuration options. Therefore, check that it works properly after installation and configuration. This is the only way to ensure that the camera will function as intended in the event of an alarm.
FlexiDomeHD 1080p IP Camera 8.2 Troubleshooting | en 39 Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution No image Defective camera. Connect a local monitor transmission to to the camera and check remote location. the camera function. Faulty cable connections. Check all cables, plugs, contacts and connections. No connection Incorrect encoder stream Select the H.
en | Troubleshooting FlexiDomeHD 1080p IP Camera Malfunction Possible causes Solution No audio Hardware fault. Check that all connected transmission to audio units are operating remote station. correctly. Faulty cable connections. Check all cables, plugs, contacts and connections. Incorrect configuration. Check audio parameters on the Audio configuration and LIVEPAGE Functions pages.
FlexiDomeHD 1080p IP Camera Troubleshooting | en 41 Malfunction Possible causes Solution The unit is not Power failure during Have the unit checked by operational after a programming by firmware Customer Service and firmware upload. file. replace if necessary. Incorrect firmware file. Enter the IP address of the unit followed by / main.htm in your Web browser and repeat the upload.
en | Maintenance FlexiDomeHD 1080p IP Camera 9 Maintenance 9.1 Testing the network connection The ping command can be used to check the connection between two IP addresses. This allows testing whether a device is active in the network. 1. Open the DOS command prompt. 2. Type ping followed by the IP address of the device. If the device is found, the response appears as " Reply from ... ", followed by the number of bytes sent and the transmission time in milliseconds.
FlexiDomeHD 1080p IP Camera Maintenance | en 43 Configuring the Terminal Before the terminal program can communicate with the camera, the transmission parameters must be matched. Make the following settings for the terminal program: – 19,200 bps – 8 data bits – No parity check – 1 stop bit – No protocol Command Inputs After the connection has been established, you must log on to the camera to access the main menu. Other submenus and functions can be accessed using the on-screen commands. 1.
en | Maintenance FlexiDomeHD 1080p IP Camera Note: You must reboot to activate the new IP address, a new subnet mask or a gateway IP address. Reboot Briefly interrupt the power supply to the camera for a reboot (disconnect the power supply unit from the mains supply and switch on again after a few seconds). Additional Parameters You can use the terminal program to check other basic parameters and modify them where necessary. Use the onscreen commands in the various submenus to do this. 9.
FlexiDomeHD 1080p IP Camera Technical Data | en 10 Technical Data 10.1 Specifications Imager Rated supply voltage 45 1/2.7-inch CMOS HD sensor 24 VAC ±10% 50/60 Hz 12 VDC ±10% Power-over-Ethernet 48 VDC nominal Current consumption 0.8 A | 1 A IVA (12 VDC) 0.7 A | 0.8 A IVA (24 VAC) 0.25 A | 0.3 A IVA (PoE 48 VDC) Minimum illumination 0.5 lx color, 30 IRE 0.
en | Technical Data LAN interface FlexiDomeHD 1080p IP Camera STP, Ethernet 10/100 Base-T, auto-sensing, half/full duplex, RJ45 Video encoding H.264 (ISO/IEC 14496-10), M-JPEG protocols Image resolutions 1920 × 1080 pixels Group of pictures IP, IBP, IBBP Network protocols HTTP, HTTPs, SSL, TCP, UDP, ICMP,RTSP, RTP, Telnet, IGMPv2/v3, SMTP,SNTP, FTP, DHCP client, ARP, DNS,DDNS, NTP, SNMP, UPnP, 802.1X, iSCSI Encryption TLS 1.
FlexiDomeHD 1080p IP Camera 10.1.1 Technical Data | en 47 Dimensions 151 (5.95) 140 (0.55) 35 (1.38) 116 (4.57) Ø208 (8.2) mm (in) Bosch Security Systems Ø150 (5.9) Installation Manual AM18-Q0601 | v1.0 | 2012.
en | Technical Data AM18-Q0601 | v1.0 | 2012.
Bosch Security Systems www.boschsecurity.