FLEXIDOME IP panoramic 6000/7000 ‑ outdoor NDS‑6004‑F180E | NDS‑6004‑F360E | NDS‑7004‑F180E | NDS‑7004‑F360E en Installation manual
FLEXIDOME IP panoramic 6000/7000 - outdoor Table of contents | en 3 Table of contents 1 Safety 4 1.1 Safety message explanation 4 1.2 Safety precautions 4 1.3 Important safety instructions 4 1.4 Data security 4 1.5 Notices 5 2 Short information 8 3 System overview 9 3.1 Intended use 9 3.2 Using the camera 9 3.3 Operation with external systems 9 3.3.1 Larger surveillance systems 10 3.4 Application variant 10 4 Planning 11 4.1 Unpacking 11 4.2 Contents 11 4.
en | Safety 1 FLEXIDOME IP panoramic 6000/7000 - outdoor Safety Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings before operating the device. 1.1 Safety message explanation Danger! Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Warning! ! Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
FLEXIDOME IP panoramic 6000/7000 - outdoor Safety | en 5 Notice! This device contains a wireless access point. Change its default password during initial configuration to maximize data security. 1.5 Notices Notice! Optical elements are sensitive and should be protected at all times. Do not allow objects to come into contact with glass surfaces and do not touch optical elements with your fingers.
en | Safety FLEXIDOME IP panoramic 6000/7000 - outdoor cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
FLEXIDOME IP panoramic 6000/7000 - outdoor Safety | en 7 Hazardous substance table according to SJ/T 11364-2014 This table was created according to the provisions of SJ/T 11364 O: The content of such hazardous substance in all homogeneous materials of such component is below the limit defined in GB/T 26572 X: The content of such hazardous substance in a certain homogeneous material is above the limit defined in GB/T 26572 The manufacturing datecodes of the products are explained in: http://www.
en | Short information 2 FLEXIDOME IP panoramic 6000/7000 - outdoor Short information This manual has been compiled with great care and the information it contains has been thoroughly verified. The text was correct at the time of publication, however, the content can change without notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between this manual and the product described.
FLEXIDOME IP panoramic 6000/7000 - outdoor 3 System overview | en 9 System overview The FLEXIDOME IP panoramic 6000 outdoor and FLEXIDOME IP panoramic 7000 outdoor are designed for outdoor use mainly due to their IK10 and IP66 ratings. The 12 MP sensor operating at 30 fps gives full panoramic surveillance with complete area coverage, fine details and high speeds. The device offers full situational awareness and simultaneous E-PTZ views in high resolution.
en | System overview – FLEXIDOME IP panoramic 6000/7000 - outdoor Add devices to your system and arrange them in groups Video Security Client The Video Security Client is a free, easy-to-use video-surveillance application provided by Bosch for local and remote monitoring of IP cameras and appliances. The software supports up to 16 cameras. The Video Security Client has extensive dewarping capabilities and can be used for client-side dewarping as well as for viewing the available modes.
FLEXIDOME IP panoramic 6000/7000 - outdoor 4 Planning 4.1 Unpacking Planning | en 11 This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all parts are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packaging is the safest container in which to transport the unit and can be used if returning the unit for service. 4.
en | Planning FLEXIDOME IP panoramic 6000/7000 - outdoor Quantity 1 Component Conduit hole adapter rubber: for diameters less than M20 (1/2 in.) 1 Screw 1 Washer 2 Grommet (plus 1 spare) 1 Desiccant bag Note: Do not open the bag before it is necessary to use its content. 4.3 1 TR20 bit 1 Quick installation guide 1 Safety instructions 3 Identification label stickers Preparation Before installation, prepare and plan the installation process and materials needed.
FLEXIDOME IP panoramic 6000/7000 - outdoor – Planning | en 13 Standard SD card (optional) Note: Bosch recommends the use of industrial SD cards with health monitoring. 4.4 System requirements To enjoy the full benefits of megapixel resolutions, ensure that the computer, the graphic adapter, the display connections, and the monitor are sufficiently powerful to view our camera images at their best.
en | Installation 5 FLEXIDOME IP panoramic 6000/7000 - outdoor Installation The device has two installation configurations: 5.1 – Installation without conduit. – Installation with conduit. Local storage Notice! Use full size SD cards for maximum reliability, and to eliminate the risk of bad connections in a microSD to full size SD adapter. Bosch recommends the use of industrial SD cards with health monitoring.
FLEXIDOME IP panoramic 6000/7000 - outdoor 1. Installation | en 15 Use the mounting template supplied to mark the position of the four holes. Make sure that the final position is correct. 2. Use an appropriate size drill to open the four holes marked before. 3. Install the four mounting plugs. 4. Put the PoE cable through the center hole of the mounting plate. 5. Put the mounting plate in position and attach it with the four screws. The screws must be 5 to 6 mm in diameter (0.20 to 0.24 in.
en | Installation FLEXIDOME IP panoramic 6000/7000 - outdoor 8. Push the grommet into the hole of the camera base, with both thumbs in opposite sides. Make sure that the grommet is fully pushed. 9. Adjust the length of the PoE cable, as necessary. 10. If necessary, do a loop with the PoE cable on the hooks of the mounting plate. 11. Align the camera base with the mounting plate.
FLEXIDOME IP panoramic 6000/7000 - outdoor Installation | en 17 13. Remove the desiccant from the bag. Note: After the desiccant is removed from the bag, the installation of the device must be done in less than 10 min. 14. Remove the protective cover from the desiccant and stick the desiccant on the camera base. 15. Connect the PoE cable to the camera module. Bosch Security Systems B.V.
en | Installation FLEXIDOME IP panoramic 6000/7000 - outdoor 16. Pre-fix the camera module to the camera base with the spring hooks. Make sure that the arrow on the camera module points in the same direction as the arrow on the camera base. 17. Attach the camera module to the camera base with the three screws. Tighten the screws with 1.5 Nm (1.1 lbfft). 2019-07 | V01 | DOC Installation manual Bosch Security Systems B.V.
FLEXIDOME IP panoramic 6000/7000 - outdoor Installation | en 19 18. If necessary, make sure that the SD card is installed on the camera module (refer to Local Storage). 19. Attach the top cover to the camera base with the four screws. Make sure that the arrow is on the same side as the arrow of the camera module. Bosch Security Systems B.V.
en | Installation 5.3 FLEXIDOME IP panoramic 6000/7000 - outdoor Installation with conduit Notice! If NDS-6004-F180E or NDS-7004-F180E are installed on a wall, it is necessary that the arrow on the device points up. This will make sure that the image is shown horizontally and in the correct angle. To install the device with the use of the conduit: 1. Use the mounting template supplied to mark the position of the five holes. Make sure that the final position is correct.
FLEXIDOME IP panoramic 6000/7000 - outdoor Installation | en 21 2. Use an appropriate size drill to open the five holes marked before. 3. Install the five mounting plugs on the surface. 4. Select the applicable conduit hole adapter and install the conduit plate hole adapter on the conduit plate: – If the conduit is M25 (0.75 in), use the conduit plate adapter with the larger hole (mounted by default). – If the conduit is M20 (0.
en | Installation FLEXIDOME IP panoramic 6000/7000 - outdoor 8. Put the mounting plate in position and attach it with the four screws. The screws must be 5 to 6 mm in diameter (0.20 to 0.24 in.) and equal or bigger than 32 mm (1¼ in.) in length. Tighten the screws between 4 and 7 Nm (3 and 5.2 lbfft). If the device is mounted on a wall, make sure that the arrow on the mounting plate points up. 9. Remove the screw from the camera base to remove the side cover. 10.
FLEXIDOME IP panoramic 6000/7000 - outdoor Installation | en 23 12. Push the grommet into the hole of the camera base, with both thumbs in opposite sides. Make sure that the grommet is fully pushed. 13. Adjust the length of the PoE cable, as necessary. 14. If necessary, do a loop with the PoE cable on the hooks of the mounting plate. 15. Align the camera base with the mounting plate.
en | Installation FLEXIDOME IP panoramic 6000/7000 - outdoor 18. Remove the protective cover from the desiccant and stick the desiccant on the camera base. 19. Connect the PoE cable to the camera module. 20. Pre-fix the camera module to the camera base with the spring hooks. Make sure that the arrow on the camera module points in the same direction as the arrow on the camera base. 2019-07 | V01 | DOC Installation manual Bosch Security Systems B.V.
FLEXIDOME IP panoramic 6000/7000 - outdoor Installation | en 25 21. Attach the camera module to the camera base with the three screws. Tighten the screws with 1.5 Nm (1.1 lbfft). 22. If necessary, make sure that the SD card is installed on the camera module (refer to Local Storage). 23. Attach the top cover to the camera base with the four screws. Make sure that the arrow is on the same side as the arrow of the camera module. Bosch Security Systems B.V.
en | Installation 5.4 FLEXIDOME IP panoramic 6000/7000 - outdoor Optional universal accessories CTN Description NDA-8000-PIPW Pendant interface plate including weather protector for outdoor use. NDA-8000-PIP Pendant interface plate for indoor use. NDA-U-PSMB Surface mount box (SMB) for wall mount or pipe mount. 2019-07 | V01 | DOC Installation manual Bosch Security Systems B.V.
FLEXIDOME IP panoramic 6000/7000 - outdoor Installation | en CTN Description NDA-U-PMT Universal pipe mount for 27 dome cameras, 31 cm, white NDA-U-PMTE Extension for universal pipe mount, 50 cm, white NDA-U-WMT Universal wall mount for dome cameras, white Bosch Security Systems B.V.
en | Installation FLEXIDOME IP panoramic 6000/7000 - outdoor CTN Description NPD-5001-POE Power-over-Ethernet midspan injector for use with PoE enabled cameras; 15.4 W, 1port NPD-5004-POE Power-over-Ethernet midspan injectors for use with PoE enabled cameras; 15.4 W, 4ports NPD-3001-WAP Bosch camera portable and wireless installation tool 2019-07 | V01 | DOC Installation manual Bosch Security Systems B.V.
FLEXIDOME IP panoramic 6000/7000 - outdoor Configuration | en 6 Configuration 6.1 Browser connection 29 A computer with Microsoft Internet Explorer is used to receive live images, control the unit, and replay stored sequences. The unit is configured over the network using the browser. 6.1.1 Establish the connection The unit must have a valid IP address to operate on your network and a compatible subnet mask.
en | Troubleshooting FLEXIDOME IP panoramic 6000/7000 - outdoor 7 Troubleshooting 7.1 Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution Unit does not operate. Power failure. Check power supply. Faulty cable connections. Check all cables, plugs, contacts and connections. No connection Incorrect unit configuration.
FLEXIDOME IP panoramic 6000/7000 - outdoor Troubleshooting | en 31 If the device is found, the response appears as "Reply from ... ", followed by the number of bytes sent and the transmission time in milliseconds. Otherwise, the device cannot be accessed via the network. This might be because: – The device is not properly connected to the network. Check the cable connections in this case. – The device is not correctly integrated into the network. Check the IP address, subnet mask, and gateway address.
en | Maintenance FLEXIDOME IP panoramic 6000/7000 - outdoor 8 Maintenance 8.1 Cleaning Bubble Cleaning If cleaning the bubble is required, use the following procedures and comply with all the warnings listed below. Cleaning the Bubble Interior The extremely soft interior surface should not be cleaned by rubbing or dusting with a cloth. Use clean dry compressed air, preferably from a spray can, to remove any dust from the interior surface.
FLEXIDOME IP panoramic 6000/7000 - outdoor Bosch Security Systems B.V.
en | Decommissioning FLEXIDOME IP panoramic 6000/7000 - outdoor 9 Decommissioning 9.1 Transfer The unit should only be passed on together with this installation guide. 9.2 Disposal Disposal - Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused.
FLEXIDOME IP panoramic 6000/7000 - outdoor 10 Technical data 10.1 Specifications Technical data | en 35 Power Power Supply Power-over-Ethernet 48 VDC nominal Power Consumption 140 mA (Essential Video Analytics - 6000 series) 200 mA (Intelligent Video Analytics - 7000 series) PoE IEEE 802.3af (802.3at Type 1) Sensor Type 1/2.
en | Technical data FLEXIDOME IP panoramic 6000/7000 - outdoor Video resolution (H x V) – 180° version Video 2 channel Video 3 channel Panoramic 2688 x 800 E-PTZ 2048 x 1152 Corridor 1600 x 1200 E-PTZ 1280 x 720 Video resolution (H x V) – 360° version Video 1 channel Full image circle 2640 x 2640 Video 2 channel Full panoramic 3584 x 504 E-PTZ 1536 x 864 Quad 1536 x 864 Panoramic 2688 x 800 Double panoramic 1920 x 1080 Corridor 1600 x 1200 E-PTZ 1280 x 720 Video 3 channel V
FLEXIDOME IP panoramic 6000/7000 - outdoor Technical data | en 37 Video functions Display stamping Individual names and stamps for all video channels Other functions Pixel counter, Video watermarking, Location Optical Lens (180° version) 2.1 mm fixed-focus lens (IR corrected), F2.8 Lens (360° version) 1.6 mm fixed-focus lens (IR corrected), F2.
en | Technical data FLEXIDOME IP panoramic 6000/7000 - outdoor Network Connectivity Auto-MDIX Interoperability ONVIF Profile S; ONVIF Profile G; ONVIF Profile T GB/T 28181 Mechanical Dimensions (∅ x H) 174.9 x 108.4 mm (6.886 x 4.267 in) Weight 2.06 kg (4.54 lbs) Color White (RAL9003) Environmental Operating Temperature -30ºC to +45ºC (-22ºF to 113ºF) Storage Temperature -20ºC to +60ºC (-4ºF to 140ºF) Operating Humidity 5% to 93% RH non-condensing 5% to 100% RH condensing 10.
FLEXIDOME IP panoramic 6000/7000 - outdoor Bosch Security Systems B.V.
| Technical data 2019-07 | V01 | DOC FLEXIDOME IP panoramic 6000/7000 - outdoor Installation manual Bosch Security Systems B.V.
Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V.
