OBD1300 Enhanced OBD I & OBD II Scan Tool en User guide
en | 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Serial No: ___________________________________ SW ID: ______________________________________ HW Ver: _____________________________________ Boot Ver: ____________________________________ Prod ID: _____________________________________ Board ID: ____________________________________ Burn Date: __________________________________ Record the above information about your tool.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 3 | en Table of Contents 1 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 Read All Instructions. . . . . . . . . . . . . . . . . 5 1.2 Safety Messages . . . . . . . . . . . . . . . . . . . . 5 2 Important Safety Warnings and Instructions. . . 5 3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.1 Introduction. .
en | 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool 7.5 Output Switch Test (EEC-IV Vehicles). . . 55 7.6 Cylinder Balance Test (EEC-IV Vehicles).55 7.7 KOER Computed Timing (1984-1991 EEC-IV Vehicles). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 7.8 STAR Test Mode (EEC-IV, MECS and MCU Vehicles). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 8 Chrysler OBD I Diagnostics. . . . . . . . .
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 5 | en 1 Safety Precautions For your safety, read this manual thoroughly before operating your scan tool. Always refer to and follow safety messages and test procedures provided by the manufacturer of the vehicle or equipment being tested. The safety messages presented below and throughout this user’s manual are reminders to the operator to exercise extreme care when using this test instrument. 1.
en | 6 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool WARNING WARNING Risk of poisoning. • Use this scan tool in locations with mechanical ventilation providing at least 4 air changes per hour. Engine exhaust contains odorless gas which can be lethal. • Route the exhaust outside while testing with the engine running. Poisoning can result in death or serious injury. Risk of flying particles.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 7 | en WARNING CAUTION Engine compartment contains electrical connections and hot or moving parts. • Keep yourself, test leads, clothing and other objects clear of electrical connections and hot or moving engine parts. • Do not wear watches, rings, or loose fitting clothing when working in an engine compartment. • Do not place tools or test equipment on fenders or other places in engine compartment.
en | 8 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool 3 Getting Started 3.1 Introduction The scan tool was developed by experts in the automotive service industry to help diagnose vehicles and assist in troubleshooting procedures. The scan tool monitors vehicle events and retrieves codes from the vehicle’s control modules to help pinpoint problem areas.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 9 | en to fine-tune their systems. Beginning in 1996, most of the new vehicles sold in the United States were fully OBD II compliant. 3.5 Data Link Connector (DLC) The data link connector (DLC) allows the scan tool to communicate with the vehicle’s computer(s). Before OBD II, manufacturers used different DLCs to communicate with the vehicle. Use the proper DLC adapter cable to connect the scan tool to the vehicle.
en | 1 0 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool included with this tool. It is available through your dealer. Use the following diagrams to connect the adapter cable. 1 nected to the white tach connector, serious damage may result and may void warranty. Refer to the illustration. GM (OBD I) Prior to 1996, most GM vehicles used the 12-pin Assembly Line Diagnostic Link (ALDL) DLC. In 1994 and 1995, certain GM vehicles used the J1962 (OBD II) DLC, but are not OBD II compliant.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 11 | en labeled Toyota 1 on the vehicle end. The adapter cable (7-0145) is included with the scan tool. SCI (P/N 7-0141) LH This DLC is used on LH platform vehicles. The LH style DLC is a small, blue, rectangular 6-pin connector located in the passenger compartment below the dashboard to the right of the steering column. The LH Adapter Cable (7-0142) is optional and must be purchased separately.
en | 1 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Powertrain Codes Code Type P0xxx P1xxx P2xxx P30xx–P33xx P34xx–P39xx Generic (SAE) Manufacturer specific Generic (SAE) Manufacturer specific Generic (SAE) 4 Using the Scan Tool 4.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 13 | en 4.2 Specifications Display • Indicates additional information is available by scrolling down. • Indicates additional information is available by scrolling up. • Indicates the internal batteries need replaced or are not installed. √ Indicates selected items in a data list or that data is available for items on the Review Data and Print Data Menu. indicates the key is active.
en | 1 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool CAUTION If the scan tool will not be used for an extended period of time, remove the batteries to prevent battery leakage from damaging the battery compartment. Vehicle Power When the scan tool is connected to the vehicle’s DLC using the OBD II adapter cable, the tool is powered by the vehicle and will automatically turn on once connected. Some vehicle cigarette lighters are not powered when the ignition is in the OFF position.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 15 | en System Setup • English/Metric Auto-Power Off Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test 2. • Quick Test Disabled QuickCheck Read All Codes Increase or Decrease Auto-Power Off time. • Use the UP key to increase time. • Use the DOWN key to decrease time. • Press . Auto-Power Off 2 minute(s) Increase time Decrease time Press ENTER to continue 3.
en | 1 6 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Print Header ON OFF 3. Long PID Names Long PID Names allows the user to enable/disable the tool scrolling the complete PID name on the bottom line of the display while viewing Live Data or viewing Freeze Data. Long PID Names are not available on GM, Ford, Chrysler, and Toyota OBD I vehicles. From System Setup menu: 1. Select Long PID Names. • Use the UP and DOWN keys until Long PID Names is highlighted. • Press .
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 17 | en System Setup • • • • English/Metric Auto-Power Off Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test 2. Tool Information Serial No SW ID HW Ver Boot Ver Prod ID Board ID Burn Date Burn Loc Increase or Decrease Pre-Trigger Frames. • Use the UP key to increase frames. • Use the DOWN key to decrease frames. • Press . Pre-Trigger Frames 5 frame(s) 3. 4.
en | 1 8 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • The first screen displayed says, “Check for missing spots in the display.” 1. Display Test Select Keypad Test. • Use the UP and DOWN keys until Keypad Test is highlighted. • Press . System Setup Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test Keypad Test Memory Test Check for spots in the display Press BACK to exit • Solid red, green, and blue screens are displayed. 2.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 19 | en • • Memory Test may take several minutes to complete. Memory Test results display: –– If no problems were detected, then “Pass” is displayed. –– If RAM fails, an error message is shown. –– If FLASH fails, a checksum is shown. Memory Test INT RAM INT FLASH Passed 10ca 4.6 Vehicle-Specific Features Review Data The Review Data function allows the user to view the information from the previous vehicle tested.
en | 2 0 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Review Data Frame: 0 Throttle position –– Recording The Recording function is used to play back a recording. This function is very similar to View Data. The only difference is that View Data is real-time viewing of PIDs, while Recording is a viewing of previously recorded PIDs. From the Review Data menu: 1. Select Recording. • Use the UP and DOWN keys until Recording is highlighted. • The tool can keep up to 5 recordings per vehicle.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 21 | en Print Data The Print Data function allows the printing of diagnostic information stored in the scan tool. • The scan tool’s internal battery power can be used to print data. • Use the Print Header function to turn ON/OFF printing vehicle information prior to printing data. • Make sure you have preciously installed the PC software in Download Scanning Suite. • Launch Scanning Suite and then start printing application.
en | 2 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • On GM OBD I, Ford OBD I, and Chrysler vehicles the MIL (Blinky) code may also be entered. To look up another DTC, press . Press again to return to the Diagnostic Menu. Vehicle? OBDII/EOBD US Europe Asia Prev: 06 Accord Prev: 04 Express 1500 Prev: 04 Express 1500 Prev: 04 Express 1500 3. Enter code. • All characters must be entered. • Only one character can be changed at a time. • Use the LEFT and RIGHT keys to scroll to desired digit.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 23 | en • Main Menu Vehicle Diagnostics Acronyms Review Data Print Data Code Lookup System Setup Press . VIN 1GCFG15T541238036 2004 Chevrolet Express 1500 5.3 Is this correct? Yes 2. Use the UP and DOWN keys to select AutoID™, Manual, or Prev:. • If the vehicle is a model year 2000 or newer, select AutoID. • If the vehicle is 1999 or older, or if the vehicle is 2000 to 2004 but does not support AutoID™, select Manual and go to Step 3.
en | 2 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • If vehicle power is not detected, a screen is shown to verify tool connection. Vehicle Required Please verify the tool is connected to the vehicle with the ignition key turned on. Press ENTER to continue • If you already have 5 vehicles in your garage, the tool will display a menu asking you which previous vehicle to replace with the currently identified vehicle.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 25 | en 2-Replaced Evaporative Emissions (EVAP) Canister Vent Solenoid/Valve 3-Replaced Ignition Switch 4-Replaced Intake Manifold 5-Repaired Mass Air Flow (MAF) Sensor Connector 6-Replaced Powertrain Control Module (PCM) 7-Programmed Powertrain Control Module (PCM) 8-Cleaned Throttle Body From the Main Menu or Diagnostic Menu: 1. Select Acronyms. • Use the UP and DOWN keys until Acronyms is highlighted. • Press .
en | 2 6 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool # Of Emiss Component Locator Number Of Emission Related DTC 4.14 Component Locator Component Locator provides a vehicle-specific location of components found on the selected vehicle. It is a useful companion function to CodeConnect®. CodeConnect® will indicate components that repaired a problem associated with a DTC, and Component Locator provides the location of the component.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 27 | en The scan tool keeps data received from the previous 5 vehicle’s selected until any of the following occurs: • A new vehicle is selected when you already have 5 in your garage forcing you to select which vehicle you want to remove from your garage to create space. • Scan tool is flash programmed to update software. On initial link to vehicle, scan tool checks the status of I/M Monitors no matter which function is selected.
en | 2 8 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • This Drive Cycle - shows status of monitors since the start of the current drive cycle. Refer to the vehicle service manual for more detailed information on emission-related monitors and their status. Some vehicles do not support This Drive Cycle. If vehicle supports both types of monitors the I/M Monitors Menu displays.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 29 | en Read Codes No codes found Press ENTER to continue 3. View and write down the DTCs. • Use the UP and DOWN keys until the desired choice is highlighted. This screen indicates where the Read Codes information is located. DTC# X/Y Module DTC Description DTC Type DTC Number - number of the trouble code found in vehicle service information.
en | 3 0 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool P2270 ----- 1/3 ECM $10 1/1 ECM Torque Converter Clutch Circuit High EGR Position High History MIL CODE 213 MIL indicates that this DTC has turned on the MIL light. P2270 Active is a DTC that was present at the time of scan tool request. 1/3 ECM $10 P0113 Torque Converter Clutch Circuit High 1/1 ECM Intake Air Temperature Sensor 1 Circuit High MIL ACTIVE Pending indicates a global OBD II/EOBD pending code. 4.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 31 | en Select Module Diagnostic Codes OBDII/EOBD Engine ABS Airbag Read Codes Erase Codes View Freeze Data Component Locator Acronyms Review Data Print Data Code Lookup System Setup • If diagnostic results and codes are not to be erased select NO and press . 4. Erase Codes Erase Codes Are you sure you want to erase diagnostic results and codes? Codes remaining:0 Yes Command sent Press ENTER to continue No 5.
en | 3 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool State OBD Check MIL is OFF OFF 0 3 4 4 MIL Status Codes Found Monitors OK Monitors Inc Monitors N/A MIL lamp should be OFF engine is running Press ENTER to continue 5.5 State OBD Check The State OBD Check function is used to display a basic status of the vehicles OBD system. • Malfunction indicator lamp (MIL) status • Codes found • I/M monitors Erase Codes deletes DTCs and resets I/M monitors from vehicle’s computer module(s).
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 33 | en • names (ID) assigned by manufacturer (i.e. $10 or $1A). If one or more control module stops responding, the scan tool displays a message. –– If continuing, dashes will replace data in right-hand column. –– If NO is selected, then the scan tool attempts to re-establish communication with that module.
en | 3 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Select Data to View ABS TPS B(%) MIL STATUS Entire Data List Custom Data List English/Metric 0.0 Off Throttle Position B 2. Select View Instructions or Not. • Use the LEFT and RIGHT keys. • Press . Custom Setup Do you want to view instructions for creating a custom data list? Yes 3. No Select PIDs to View. • Use the UP and DOWN keys to move up and down list. • The RIGHT arrow selects or deselects data parameter.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 35 | en • • • Validating PIDs Validating PID List Record Data PID 116/329 Please Wait 3. Select Data to Record 4. Playback data? Refer to”5.6 View Data” on page 32 to setup Custom List or View Entire List and Pre-Trigger Setup to set the number of frames to keep prior to triggering the recording. Entire Data List Custom Data List Pre-Trigger Setup Press to begin recording.
en | 3 6 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • Refer to “11 Appendix A—Global OBD II PID Definitions” on page 63. TROUB CODE FUEL SYS 1 FUEL SYS 2 CALC LOAD(%) COOLANT (°F) ST FTRM1(%) LT FTRM1(%) MAP(”HG) ENG SPEED(RPM) VEH SPEED(MPH) P2122 N/A N/A 0.0 -40 0.0 0.0 28.1 0 0 Reset monitors by: • Erasing codes. • Vehicle computer module losing power (on some vehicles). From Special Tests Menu: 1. Select Drive Cycle Monitor.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 37 | en 5.10 This Drive Cycle Catalyst Mon Oxygen Sens Mon Oxygen Sens Htr EGR/VVT Sys Mon inc inc inc inc OR Since DTCs Cleared Misfire Monitor Fuel System Mon Comp Component Catalyst Mon Htd Catalyst Evap System Mon Sec Air System A/C Refrig Mon Oxygen Sens Mon • • ok ok ok ok n/a inc n/a n/a ok The scan tool display is continuously updated. Monitors that are “ok” will disappear and only the “inc” monitors will remain displayed.
en | 3 8 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool 2. Select O2 sensor. • Use the UP and DOWN keys until the desired O2 monitor is highlighted. • Press . Special Tests I/M Monitors Drive Cycle Monitor State OBD Check MIL Status O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Charging System Monitor Select O2 Sensor O2 Bank1 Sensor1 • 2. • 3.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 39 | en Test $03 ID MOD MAX MEAS MIN STS • Special Tests 01 $09 ---00 00 OK On CAN vehicles scan tool displays: –– Test performed. The test performed can be $## if test is not defined. Refer to vehicle service manual for details. –– Measured values and units of measured (such as volts, amps, and seconds). –– Status of monitor test data. –– Module ID where the monitor test data came from.
en | 4 0 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • CVNs are reported to determine if emission-related calibrations have been changed. Multiple CVNs may be reported for a control module. • In-use performance tracking tracks performance of key I/M Monitors. From Special Tests Menu: 1. Select Vehicle Information. • Use the UP and DOWN keys until Vehicle Information is highlighted. • Press . Vehicle Information Retrieving CVN data. It may take up to 1.5 minutes.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 41 | en Sensor Monitor Completion Counts O2SCOMPX O2 Bank x Sensor Conditions Encountered O2SCONDX O2 Counts Bank x Monitor Completion Condition EGRCOMP EGR Counts Monitor Conditions Encountered EGRCOND EGR Counts AIR Monitor Completion Condition AIRCOMP Counts (Secondary Air) AIR Monitor Conditions Encountered AIRCOND Counts (Secondary Air) Monitor Completion Condition EVAPCOMP EVAP Counts Monitor Conditions Encountered EVAPCOND EVAP Counts VIN (M
en | 4 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Oil Light Reset Cycle key, Turn engine off, Key on Press BACK to exit Press ENTER to continue 3. battery) or a battery with a different capacity (mAh), the vehicle may require reprogramming to the new battery type in addition to performing the battery reset. Reprogramming is not a function of the tool. Consult the vehicle manual for additional vehicle-specific information. From the Special Tests Menu: 1. Select Battery Reset.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 43 | en Battery Reset Charging System Monitor Battery System Reset Complete DLC KOEO Voltage: 12.2V Please start the engine Press ENTER to continue 5.16 Charging System Monitor Press BACK to exit 4. The Charging System Monitor function allows the scan tool to provide voltage measurements at the DLC to give an indication of battery, starter, and alternator performance. From the Special Tests Menu: 1. Select Charging System Monitor.
en | 4 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Test Results DLC KOEO Voltage DLC Cranking Voltage DLC KOER Voltage Special Tests 12.2 10.4 14.7 O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Oil Light Reset Charging System Monitor Modules Present Component Locator Acronyms ess ENTER to view the data plot. On the first screen, the scan tool didn’t detect that the engine had started, so there isn’t a KOER voltage reading.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 45 | en Since CAN vehicles use module IDs larger than 2 digits, the scan tool assigns a 2 digit module ID to be used in place of the actual CAN module ID. The module ID assigned for the CAN module ID is used in all functions of the scan tool. • ISO 14230-4 protocol is shown as K2K (Keyword 2000).
en | 4 6 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • Press . Select Category Engine 2 Engine 3 3. Select the type of data to review. • Use the UP and DOWN keys until data is highlighted. Refer to ”5.6 View Data” on page 32 for Entire or Custom Lists. • Press . Select Data to View Entire Data List Custom Data List English/Metric 4. View PIDs on scan tool. • Use the UP and DOWN keys. Refer to ”5.6 View Data” on page 32 for additional information.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 47 | en 22 Erase Codes 3/20 ECM Pedal Position 1 Input Signal Voltage Is Too Low Are you sure you want to erase diagnostic results and codes? HISTORY Yes 3. Return to Diagnostic Codes Menu. • Press . 6.5 • Selecting NO displays a “Command cancelled” message. Erase Codes Erase Codes The Erase Codes function deletes DTCs and resets I/M Monitor data from vehicle’s control module(s). Perform this function with KOEO or KOER.
en | 4 8 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool 2. 3. 4. Locate fuse box and remove ECM fuse. Wait 20 seconds. Replace the fuse. Alternate Method 2: 1. Turn ignition key off. 2. Remove power from the scan tool. 3. Disconnect scan tool from the vehicle. 4. Disconnect Negative (-) battery cable. Wait 30 seconds, then replace the cable. The computer has a learning ability to compensate for minor variations in engine operation.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 49 | en Code 23 will look like: FLASH-FLASH-pause-FLASH-FLASH-FLASH — long pause. 4. When Field Service mode is on, most computer controlled relays and solenoids will be turned on, except for the fuel pump relay and fuel injectors. Toggle the Field Service mode ON and OFF. • Use a voltmeter to measure Relays and Solenoids input voltage to verify ON/OFF conditions.
en | 5 0 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool on. Cycle the ignition key to off for 10 seconds, then on. This may be required because the Ford system allows only one Self-Test function to be performed for each key on. Attempt the test again and if the problem remains, refer to ”10.1 Error Messages” on page 61. Datastream Menu functions are used to view and record engine data transmitted from the vehicle on EEC-IV vehicles beginning in 1990.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 51 | en 118 1/17 ECM ECT Above Max Voltage -40 F Indicated KOEO 3. Return to Diagnostic Codes Menu. • Press . Read KOER Fast Codes / Read KOER Slow Codes The Read KOER Codes function activates the key on engine running (KOER) self-test which retrieves KOER DTCs that are present when the engine is running. When the trouble condition is inactive, the KOER code is no longer sent through the datastream.
en | 5 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool 121 2/19 ECM TPS/Pedal Position Out Of Range 3. KOER • Wait 10 seconds. • Turn ignition key on. • Press after each message. Erase memory codes. • Press to begin erasing codes, which takes less than one minute to run. Erase Codes 4. 7.2 Return to Diagnostic Coddes Menu. • Press .
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 53 | en Erase Codes Turn Key Off Remove battery cable. Hold brake pedal down for 10 seconds. Replace battery cable. Press ENTER when done 3. 7.3 Return to Diagnostic Codes Menu. • Press or • press . PCM. During this test, the tool prompts the user to perform the following steps: • Press speed control ON button. • Press speed control OFF, RESUME, COAST, and ACCEL buttons. • Tap brake and clutch pedals. 3. View and write down the DTCs.
en | 5 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool CAUTION The Read KOER test is done with the engine running. Do not over-rev the engine. Observe all safety precautions. During testing, it is very important that each required step be performed when prompted by the scan tool. Failure to perform these steps may set DTCs in the PCM. Be sure to observe the tool display for indications to perform these steps. Do not touch the throttle pedal during testing.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 55 | en KOEO Wiggle Test Wiggle Test running Status Fault Present CAUTION Avoid cooling fan! It may turn on during test. The test screen indicates the time remaining. Do not touch vehicle or tools during this time until the next screen appears. Output Switch Test Return to On Demand Tests Menu. • Press . Perform the “Read KOEO Fast Codes / Read KOEO Slow Codes” on page 6-5 to retrieve the Continuous Memory DTC(s) set during the wiggle test.
en | 5 6 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool From On Demand Tests Menu: 1. Select Cylinder Balance Test. • Use the UP and DOWN keys until Cylinder Balance Test is highlighted. • Press . –– On Demand Tests KOEO Wiggle Test KOER Wiggle Test Output Switch Test Cylinder Balance Test KOER Computed Timing STAR Test Mode Acronyms Review Data Print Data 5.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 57 | en system section in the appropriate service manual for specific instructions.) From On Demand Tests Menu: 1. Select KOER Computed Timing. • Use the UP and DOWN keys until KOER Computed Timing is highlighted. • Press . On Demand Tests KOEO Wiggle Test KOER Wiggle Test Output Switch Test Cylinder Balance Test KOER Computed Timing STAR Test Mode Acronyms Review Data Print Data CAUTION Avoid cooling fan! It may turn on during test. 2.
en | 5 8 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool STAR Test Mode 54 Test/Hold On: Test ENTER to hold • 3. With the STI in the TEST state, the self-test begins. A beep accompanies each time STO is low. When a completed 2-digit or 3-digit code is received, it is shown on the display. Write down the 2-digit or 3-digit code for reference. • If necessary, refer to the appropriate service manual for procedure on how to use STAR Test Mode for the specific vehicle under test.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 59 | en • • Use the UP and DOWN keys until desired choice is highlighted. For additional View Data information, refer to ”5 OBD II Diagnostics” on page 26. Press . • Select Data to View Entire Data List Custom Data List English/Metric 2. The scan tool can maintain 5 recordings per vehicle. If there are already 5 recordings stored, the scan tool will ask which recording to overwrite.
en | 6 0 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool 3. trip but did not turn on the MIL light. If the vehicle does not support this function, then the tool will not display it. Return to Diagnostic Codes Menu. • Press . 8.5 Erase Codes The Erase Codes function deletes DTCs and resets I/M Monitor data from vehicle’s control module(s). Perform this function only after the systems have been checked completely and DTCs have been documented. This function should be performed KOEO.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 61 | en 24 Diagnostic Codes Read Codes Erase Codes Acronyms Review Data Print Data Code Lookup System Setup 2. Follow the instructions step-by-step: • Set parking brake. • Transmission in park (P) or neutral (N). • Turn A/C off. • Start engine and let idle until hot. • Turn ignition key off. • Wait 10 seconds. Turn key on-engine off. Do not start engine. Read Codes 1) Do all test steps: 2) Set parking brake. 3) Trans in P or N. 4) Turn A/C off.
en | 6 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool • • • • • • • Look at DLC and check for cracked or recessed pins, or for any substance that could prevent a good electrical connection. Test for continuity between the DLC wiring and the computer. In an extreme case, there may be a broken wire. Check for bent or broken pins. With the engine off, check for blown fuses in the vehicle fuse box. Make sure the vehicle’s control module has a good ground.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 63 | en 10.7 Technical Support Toll-Free Number: 1-800-228-7667. 11 Appendix A—Global OBD II PID Definitions Although there are in excess of 300 PIDs, the tool only displays the PIDs the vehicle supports.
en | 6 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool PID PID Description PID PID Description EGT 13, 23 Exhaust Gas Temperature (EGT) Bank 1 Sensor 3, Bank 2 Sensor 3 Exhaust Gas Temperature (EGT) Bank 1 Sensor 4, Bank 2 Sensor 4 Emission requirements to which vehicle is designed Time Since Engine Start Engine RPM Engine Oil Temperature Exhaust Pressure Sensor Bank 1, Bank 2 Equivalence Ratio Commanded EVAP Purge EVAP Vapor Pressure Absolute EVAP Vapor Pressure Fuel Rail Pressure A, B M
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 65 | en PID PID Description SCR SYS ACTIVE SCR inducement system actual state: inducement system active Distance travelled in current 10K block SCR_DIST_1D (0 - 10000 km) Distance travelled while inducement system active in current 10K SCR_DIST_1N, block 1N (0 - 10000 km), 20K block 2N, 3N, 4N 2N (10 - 20000 km), 30K block 3N (20 - 30000 km), 40K block 4N (30 - 40000 km) SECOND AIR Secondary Air Status ST FTRM Fuel Trim Bank / Sensor ST FTRM1, 3
en | 6 6 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Barometric pressure sensor. See MAP sensor. BBV: Brake boost vacuum (sensor) BCM: Body control module Boost control solenoid: A solenoid that is energized by the PCM, in order to control turbo/supercharger boost pressure. Brake switch signal: An input signal to the PCM indicating that the brake pedal is being pressed. This signal is typically used to disengage cruise control systems and torque converter clutch (TCC) solenoids. See also TCC.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 67 | en EOT: Engine oil temperature (sensor) EPA: Environmental protection agency ESC: Electronic spark control. An ignition system function that warns the PCM when knock is detected. The PCM then retards spark timing to eliminate the knocking condition. EST: Electronic spark timing. An ignition system that allows the PCM to control spark advance timing.
en | 6 8 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Multi-port fuel injection. MPFI is a fuel injection system using one (or more) injector(s) for each cylinder. The injectors are mounted in the intake manifold, and fired in groups rather than individually. NOx: Oxides of nitrogen. The system EGR and Camshafts injects exhaust gases into the intake manifold to reduce these gases at the tailpipe. O2S: Oxygen sensor. Generates a voltage of 0.6 to 1.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 69 | en Sequential fuel injection or sequential electronic fuel Injection. A fuel injection system that uses one or more injectors for each cylinder. The injectors are mounted in the intake manifold and are fired individually. Solenoid: A device consisting of an electrical coil which when energized, produces a magnetic field in a plunger, which is pulled to a central position. A solenoid may be used as an actuator in a valve or switch.
en | 7 0 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool 13 Appendix C—OBD I Data Link Connectors Eldorado, Seville Fleetwood Grand Am 94-95 GM Cars, Light Trucks & Vans Gran Prix F E D C B A LeSabre Lumina, Monte Carlo Regal G H J K L M ALDL DLC Riviera OBD II (J1962) DLC Roadmaster Satrum SC1, SL, SL1, SW1 Satrum SC2, SL, SL2, SW2 Skylark 4.6L OHC Y, 9 94-95 ALDL 4.6L OHC Y, 9 94-95 ALDL 5.7L TBI, SFI P 94-95 ALDL 2.3L PFI DOHC A, D 94-95 ALDL 2.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 71 | en S Series 4x2 & T Series 4x4 Small Coventional Cab, Blazer, Bravada, Jimmy, Pickup & Sonoma U&X Series 4x2 All Purpose Vehicle, Lumina APV, Silhouette, Trans Sport 2.2L MFI 4.3L CPI 4.3L TBI 4 94-95 OBD II W 94 95 ALDL OBD II 94 95 ALDL OBD II Z 3.1L TBI D 94-95 ALDL 3.8L PFI L 94-95 ALDL Continental 3.8L, 4.6L, 5.
en | 7 2 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Mustang 2.3L,2.3L Turbo, 5.0L, 5.0L HO, 5.0L SHP 84-85 EEC-IV 86-93 Center of left fender apron Town Car Left rear corner of engine compartment on shock tower 94-95 4.6L 95 OBD II Below instrument panel right of steering wheel 4.6L, 5.0L 84 85-90 EEC-IV* Above right wheel well Left fender apron, near or above wheel well Rear of right shock tower 3.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 73 | en F-Series Pickup Ranger 4.9L, 5.0L, 5.8L, 84-87 7.3L D, 7.3L TD, 7.5L 88-95 EEC-IV 5.8L > 8,500 GVW 96-98 EEC-IV Left rear of engine compartment 5.8L>8,500 GVW in 49 States, ex CA 97 EEC-IV Left rear of engine compartment 7.0L 91-96 EEC-IV Left rear of engine compartment 7.0L > 14,000 GVW 97-98 EEC-IV Left rear of engine compartment 7.5L W/Fed Emiss 96 EEC-IV Left rear of engine compartment 7.
en | 7 4 | User guide | OBD1300 Enchanced ODB I & OBD II Scan Tool Neon ALL 95 OBD II Under left side of dash. New Yorker ALL 89-93 SCI 94-95 LH Front of left shock tower near the SBEC/ SMEC module Right of steering column under dash Pickup D/W, RAM Series 5.2L, 5.9L 89-95 3.9L, 5.9L 89-95 8.
OBD1300 Enchanced ODB I & OBD II Scan Tool | User guide | 75 | en 14 Limited Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGINAL RETAIL BUYERS OF BOSCH ELECTRONIC DIAGNOSTIC TOOLS (“UNITS”). BOSCH Automotive Service Solutions LLC Units are warranted against defects in materials and workmanship for one year (12 months) from date of delivery.
Bosch Automotive Service Solutions Inc. 3000 Apollo Drive Brook Park, OH 44142 USA Telephone 1-800-228-7667 www.boschdiagnostics.
