3FHJTU FS ZPVS OFX EF WJDF PO .Z#PT DI OPX BOE HFU GSF F CFOF GJUT CPTDI IPNF XFMDP DPN NF Gas hob PCH6A5B90A, PCI6A5B90A, PCR7A5B90A, PCS7A5B90A, PCT9A5B90A, PCR9A5B90A This cooktop is approved for use with Natural Gas and Universal LPG. Leave these instructions with the owner.
en Table of contents [en]I nst r uct i on manual Gas hob 8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ( Important safety information . . . . . . . . . . . . . . . 4 What to do if you smell gas . . . . . . . . . . . . . . . . . . . . . 4 5 Installation and connection. . . . . . . . . . . . . . . . . 5 Statutory requirements . . . . . . . . . . . . . . . . . . Preparing to install . . . . . . . . . . . . . . . . . . . . . Clearances . . . . . . . . . . . . . . . . . . . . . .
Intended use 8Intended use Read these instructions carefully. You will only be able to use your appliance safely and effectively when you have read them. These operating and installation instructions should be retained, and passed onto the buyer if the appliance is sold. Removal of transit protection Packaging materials of the product are manufactured from recyclable materials. Do not dispose of the packaging materials together with the domestic or other wastes.
en Important safety information (Important safety information : Warning – Risk of fire! DO NOT MODIFY THIS APPLIANCE. DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE APPLIANCE STORAGE DRAWER OR NEAR THE APPLIANCE. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. DO NOT USE THIS APPLAINCE AS A SPACE HEATER. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
Installation and connection 5Installation and connection I n s t a l a t i on a n d c o n e c t i o n Statutory requirements This installation must conform with the following: ■ Manufacturer’s Installation instructions ■ Local Gas Fitting Regulations ■ Municipal Building Codes ■ Refer to AS/NZS 5601.1 for Gas Installations ■ S.A.A. Wiring Code ■ Local Electrical Regulations ■ Any other statutory regulations D Refer to AS/NZS 5601.1 for piping size details.
Installation and connection en If the base of the hotplate can be touched, a protecting shield must be fitted. F ■ ■ ■ ■ PLQ PLQ The shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm. The shield material must be mdf or similar with minimum thickness of 12 mm. The shield overall dimensions must be 560 mm wide x 480 mm deep.
Installation and connection Depending on the model, the adhesive seal may be factory-fitted. If this is the case, it should not be removed under any circumstances, since the adhesive seal prevents leaks. If the seal has not been factoryfitted, apply it to the underside of the hob. Fitting the appliance onto the kitchen unit: 1. Screw each one of the clips into the position indicated so that they are free to rotate. 2. Insert the appliance evenly into the cut-out. 3. Turn the clips and tighten them fully.
en Installation and connection Gas connection During the planning stage, consider the position of supply connections. The cooktop must be connected to the gas supply with upstream connection of an isolation valve in accordance with the respectively valid regulations. We recommend that the isolation valve be fitted prior to the cooktop to enable isolation of cooktop from gas supply. The valve must be easily accessible at all times.
Installation and connection en Replacing the injectors Request change-over injectors from our customer service deparment (refer injector chart below for sizes). Economy burner Standardoutput burner High-output burner Mini-wok burner Wok burner 4 kW Dual wok burner 5 kW Natural Gas Hourly Gas Consumption (MJ) 4 6.85 88 Universal LPG Hourly Gas Injector Consumption mark (MJ) 3.5 50 116 6 Injector mark 66 Adjusting the gas valves 11 153 11 87 13.6 168 10.5 90 15 181 13 98 19.
Getting to know your appliance en *Getting to know your appliance Get i ng t o know your ap l i ance Burner locations 3&+ $ % $ 3&6 $ % $ 1 1 2 2 3&, $ % $ 3&5 $ % $ 1 1 2 2 3&7 $ % $ 3&5 $ % $ 1 1 2 ! Pan supports " Control knobs # Economy burner with an output of up to 1 kW $ Standard-output burner with an output of up to 1.75 kW % High-output burner with an output of up to 3 kW & Mini wok burner up to 3.
Getting to know your appliance Controls and burners Each control knob is marked with the burner it controls. You can use the control knobs to set the output required in each case to various positions between the maximum and the minimum settings. Never try to switch directly from position 0 to position 1 or from position 1 to position 0. en It is essential to ensure that all the burner parts and pan supports are correctly installed for the appliance to work correctly. Do not swap the burner caps around.
en Gas burners Simmer plate This accessory part is only suitable for simmering. It can be used with the economy burner or the standard-output burner. If your hob has several standardoutput burners, we recommend placing the simmer plate on the rear or front-right standard-output burner. Place the accessory component with the projections facing upwards on the holder; never place it directly on the burner. Simmer cap Only use the cap for cooking with minimal power.
Settings table and tips en Instructions for use Table of cooking times Note: When using certain pots or pans, a slight and temporary deformation of the steel cooking surface may occur. This is normal and does not affect the functionality of the appliance. The table below lists the optimal heat settings and cooking times for various types of food. The information given applies when cooking four portions.
en ■ ■ Settings table and tips Step 1: Bring to the boil. Set heat setting 8 for 7-9 minutes. Step 2: Continue boiling. Switch to heat setting 1 for 5-8 minutes. This information also applies for the other suggested burners. Food Burner Total Step 1 time in ˜ § v min.
Settings table and tips Food Burner Total Step 1 time in ˜ § v min.
en Cleaning and maintenance Food Burner Total Step 1 time in ˜ § v min.
Trouble shooting en 3Trouble shooting DO NOT MODIFY THIS APPLIANCE. Only authorized personnel from the Service Centre are qualified to work on the appliance. Sometimes certain faults detected can be easily resolved. Before calling the Technical Assistance Service, bear in mind the following advice: Tr oubl e sho t i ng Fault The general electrical system is malfunctioning. The automatic switching on function does not work. The burner flame is not uniform. The gas flow is not normal or there is no gas.
en Customer service 4Customer service When contacting our customer service, please provide the product number (E-Nr.) and production number (FD) of the appliance. This information is given on the specifications plate located on the lower section of the hob and on the label in the user manual. After-sales contact details for all countries can be found in the attached after-sales service directory.
5IBOL ZPV GPS CVZJOH B #PTDI )PNF "QQMJBODF 3FHJTUFS ZPVS OFX EFWJDF PO .
