3FHJTU FS ZPVS OFX EF WJDF PO .Z#PT DI OPX BOE HFU GSF F CFOF GJUT CPTDI IPNF XFMDP DPN NF Gas hob PPH6A6B20A, PPQ7A6B20A This cooktop is approved for use with Natural Gas and Universal LPG. Leave these instructions with the owner.
en Table of contents [ en] I nst r uct i on manual 8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ( Important safety information . . . . . . . . . . . . . . . 3 What to do if you smell gas . . . . . . . . . . . . . . . . . . . . . 4 5 Installation and connection. . . . . . . . . . . . . . . . . 5 Statutory requirements . . . . . . . . . . . . . . . . . . Preparing to install . . . . . . . . . . . . . . . . . . . . . Clearances . . . . . . . . . . . . . . . . . . . . . . . . .
Important safety information This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
en Important safety information Risk The of fire! burners get very hot. Do not rest inflammable objects on the hob. Do not store objects on the hob. Risk fire!store or use corrosive chemicals, ■ Doofnot products which produce fumes, inflammable materials or non-food products below or near this domestic appliance. Risk ofor fire! ■ Fat oil which is overheated can catch fire easily. Never leave fat or oil to heat up unattended. If oil or fats do catch fire, never use water to put the fire out.
Installation and connection 5Installation and connection I n s t a l a t i on a n d c o n e c t i o n Statutory requirements This installation must conform with the following: ■ Manufacturer’s Installation instructions ■ Local Gas Fitting Regulations ■ Municipal Building Codes ■ Refer to AS/NZS 5601.1 for Gas Installations ■ S.A.A. Wiring Code ■ Local Electrical Regulations ■ Any other statutory regulations en Preparing to install Refer to AS/NZS 5601.1 for piping size details.
en Installation and connection D 5 E PLQ PLQ PLQ PD[ 5 PLQ PLQ PLQ PLQ PLQ PLQ Clearances A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan.
Installation and connection Installation of cooktop into the kitchen bench Side clearances: If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance with clauses 6.10.1.2 of AS/NZS 5601.1. Make an appropriate size cut in the worktop surface, depending on the installation method. standard (a) or flush (b). For flush installation: ■ ■ ■ ■ All cuts in the worktop surface should be done by a specialised shop.
en Installation and connection Wiring diagram Position of the inlet connection: a a a A B C D E Switch Blue wire Brown wire Terminal Ignition module Gas connection During the planning stage, consider the position of supply connections. The cooktop must be connected to the gas supply with upstream connection of an isolation valve in accordance with the respectively valid regulations.
Installation and connection Converting the cooktop from Nat. Gas to Universal LPG en All work involved in installation, setting and adaptation to a different gas type must be carried out by a licensed gas fitter and must comply with current regulations and the conditions laid down by the local gas company. Before conversion the cooktop must be disconnected from the electricity and gas valves must be turned to the OFF position.
Getting to know your appliance en *Getting to know your appliance Get i ng t o know your ap l i ance Burner locations 33+ $ % $ 1 Controls and burners Each control knob is marked with the burner it controls. You can use the control knobs to set the output required in each case to various positions between the maximum and the minimum settings. Never try to switch directly from position 0 to position 1 or from position 1 to position 0.
Gas burners Accessories Depending on the model, the hob may include the following accessories. These can also be acquired from the Technical Assistance Service. Additional wok grid Only suitable for use on wok burners. Use cookware with a rounded base. To extend the service life of the appliance, we recommend using the additional wok grid. en ÄGas burners Gas bur ner s Switching on manually 1. Press the control knob for the selected burner and turn it anticlockwise to the highest power setting. 2.
en Settings table and tips An orange-coloured flame is normal. This is caused by the presence of dust in the atmosphere, spilt liquids, etc. In the event of the burner flames being accidentally extinguished, turn off the burner control and do not attempt to re-ignite the burner for at least one minute.
Settings table and tips Table of cooking times ■ The table below lists the optimal heat settings and cooking times for various types of food. The information given applies when cooking four portions. The cooking times and heat settings may vary depending on the type of food, its weight and quality, on the type of gas used, and on the material from which the cookware is made. To prepare this dish, stainless steel cookware was mainly used.
en Settings table and tips Food Burner Total Step 1 time in ˜ § v min.
Settings table and tips Food Burner Total Step 1 time in ˜ § v min.
en Cleaning and maintenance Cooking tips ■ Use a pressure cooker to cook creamy soups and pulses. This significantly reduces the cooking time. If you are using a pressure cooker, follow the manufacturer's instructions. Add all of the ingredients at the start. ■ Always use a lid when cooking potatoes and rice. This significantly reduces the cooking time. The water must be boiling before you add pasta, rice or potatoes. Then adjust the heat setting to continue boiling.
Trouble shooting en 3Trouble shooting DO NOT MODIFY THIS APPLIANCE. Only authorized personnel from the Service Centre are qualified to work on the appliance. Sometimes certain faults detected can be easily resolved. Before calling the Technical Assistance Service, bear in mind the following advice: Tr oubl e sho t i ng Fault The general electrical system is malfunctioning. The automatic switching on function does not work. The burner flame is not uniform. The gas flow is not normal or there is no gas.
en Customer service 4Customer service When contacting our customer service, please provide the product number (E-Nr.) and production number (FD) of the appliance. This information is given on the specifications plate located on the lower section of the hob and on the label in the user manual. After-sales contact details for all countries can be found in the attached after-sales service directory.
5IBOL ZPV GPS CVZJOH B #PTDI )PNF "QQMJBODF 3FHJTUFS ZPVS OFX EFWJDF PO .
