RPS D5500CU en Installation Guide
RPS Table of Contents | en 3 Table of Contents 1 Legal 5 1.1 Trademarks 5 1.2 Software License Agreement 5 2 Introduction 8 2.1 Release Notes 8 2.2 RPS Minimum System Requirements 8 2.3 Minimum System Requirements for SQL Express Only 9 2.4 RPS and SQL Express on the Same PC Minimum Requirements 2.5 Minimum System Requirements for RPS and SQL Express on a PC with Vista 10 2.6 Minimum System Requirements for RPS and SQL Express on a PC with Windows 7 11 3 Install RPS 12 3.
en | Table of Contents RPS 4.2.5 Upgrade RPS 43 4.3 Share the SQL Database 46 4.4 Integrate the RPS Database Files into the SQL Database 47 4.4.1 Automatic Integration 47 4.4.2 Manual Integration 47 4.4.3 Upgrade from RPS 5.11 or Lower 48 4.4.4 Create a New Database 48 4.4.5 Conversion Log File 48 5 Log into RPS 49 5.1 First Time Log-In 49 5.2 Change the Password 50 6 Maintenance 51 6.1 Set Security Levels by Panel Type for Networked Users 51 6.
RPS Legal | en 1 Legal 1.1 Trademarks – 5 Microsoft, Windows 7, XP, Vista and SQL Server are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. – InstallShield is a registered trademark and service mark of Acresso Software in the United States and other countries. – Intel is a registered trademark of Intel Corporation in the United States and other countries.
en | Legal RPS part, all of which are the valuable property of Bosch and/or its suppliers. You may not remove, change or delete the copyright notice from the Software. If you make any copies of the Software in whole or in part, all such copies shall contain the same copyright and proprietary markings as appear on or in the original Software copy, including media markings.
RPS Legal | en 7 restrictions and requirements. If you, the licensee, are a U.S. citizen or you will take delivery of the Software inside the United States, then you agree to not export the Software from the United States without complying with all applicable U.S. Government restrictions and requirements, including obtaining any necessary U.S. Government authorization for the export.
2 en | Introduction RPS Introduction RPS (Remote Programming Software) is a Windows®-based account management and control panel programming utility designed to remotely set up and program specific control panels. 2.1 Release Notes The Release Notes provide additional information about RPS that became available after the printing of this manual. Review these notes before using RPS. The Release Notes also list control panels that are compatible with RPS. 2.
RPS 2.3 Introduction | en 9 Minimum System Requirements for SQL Express Only Processor: Operating System: Pentium III Compatible or higher – Minimum: 500 MHz – Recommended: 1 GHz or higher – Microsoft® Windows 7 SQL Server Express SP3 is required for Windows 7, which is provided on the RPS CD-ROM.
2.4 en | Introduction RPS RPS and SQL Express on the Same PC Minimum Requirements Processor: Intel Pentium IV Operating System: – Microsoft Windows 2003 Server with Service Pack 1 – Microsoft Windows XP Professional with Service Pack 2 – Microsoft Windows XP Home Edition with Service Pack 2 – Minimum: 512 MB – Recommended: 1 GB or higher RAM: Hard Drive Space: Approximately 512 MB for RPS installation. Accounts and history require additional hard drive space.
RPS 2.6 Introduction | en 11 Minimum System Requirements for RPS and SQL Express on a PC with Windows 7 Processor: 1 GHz or faster 32-bit (x86) or 64-bit (x64) processor Operating System: – Microsoft Windows 7 (all versions) RAM: – 32-bit: 1 GB – 64-bit: 2 GB – 32-bit: At least 16 GB available hard drive space – 64-bit: At least 20 GB available hard drive space Hard Drive Space: Video: VGA monitor capable of supporting 1024 x 768 resolution. RPS supports 24-bit color palettes and lower.
en | Install RPS RPS 3 Install RPS 3.1 Overview NOTICE! To install or upgrade RPS, the RPS operator must have administrative rights on the target computer. Once RPS is installed or upgraded, the RPS operator does not need administrative rights to use RPS on the target computer. NOTICE! If you are using an unreleased version of RPS, such as an alpha or beta version, you must uninstall (remove) RPS before installing a released version.
RPS Install RPS | en 3. From the instruction window, you can open the RPS documentation and install RPS. 4. Click Install to start the installation process. 13 You are ready to prepare the installation of the SQL database and RPS. Bosch Security Systems, Inc. Installation Guide 4998141259 | 12 | 2011.
en | Install RPS 3.2.2 RPS Prepare the Installation of the SQL Database and RPS 1. 2. If prompted for a setup language, select your language and then click Next. The Database Location window opens. Select Local to install the SQL database on the same computer as RPS. Click Next. 3. The SQL Instance window opens. Select an existing SQL instance, or create a new instance, and then click Next. For more information, refer to: – Section 3.4 Use an Existing SQL Instance, page 27 – Section 3.
RPS Install RPS | en – 15 If you need to change any settings, click Back to review and modify the previous installation setup windows as needed. – If you would like to print the installation summary, click Print. – If you are ready to install the SQL database and RPS, click Next. The installation process starts. Bosch Security Systems, Inc. Installation Guide 4998141259 | 12 | 2011.
en | Install RPS 3.2.3 RPS Install the SQL Database and RPS Install the SQL Database The installation of the SQL database is automatic. No user interaction is needed. When the SQL database installation is complete, the RPS installation starts. Install RPS Use the following steps to install RPS: 1. 2. When the Welcome window opens, click Next. The Choose Destination Location window opens. If the default directory is acceptable, click Next.
RPS Install RPS | en 4. The Select Program Folder window opens. Click Next. 5. The Start Copying Files window opens. Click Next. 17 The Setup Status window indicates the installer's progress. Bosch Security Systems, Inc. Installation Guide 4998141259 | 12 | 2011.
en | Install RPS RPS 6. When the InstallShield Wizard Complete window opens, click Finish. The computer restarts. 7. After logging onto the computer, start RPS by selecting Start>Bosch>RPS 5.x, or by double-clicking the RPS 5.x shortcut on the computer's desktop. 8. In the RPS Logon Information window, enter your RPS user name and password, then click OK. 9. – The default user name is admin – The default password is 1111 or default By default, the Panel List opens.
RPS Bosch Security Systems, Inc. Install RPS | en Installation Guide 19 4998141259 | 12 | 2011.
en | Install RPS RPS 3.3 Install RPS with a Network SQL Database 3.3.1 View the RPS Documentation and Start the Installation Process 1. Insert the RPS CD-ROM into your CD-ROM drive. The RPS startup program should automatically start. If the startup program does not automatically start: a. Select Start > Run… b. At the prompt, type: X:\setup.exe. "X" = the drive letter assigned to your CD-ROM drive. 2. When the startup window opens, select a language from the list provided.
RPS 3.3.2 Install RPS | en 21 Prepare the Installation of the SQL Database and RPS 1. The Installation Language window opens. Select your setup language preference, and then click Next. 2. The Database Location window opens. Select Network to install the SQL database on a network instead of on the same computer that RPS is installed on. Click Next. 3. The SQL Instance window opens. Select an existing SQL instance, and then click Next. For more information, refer to Section 3.
en | Install RPS RPS NOTICE! If RPS has never been installed on the target computer, then there will not be any existing databases to select from. In this case, select Create new RPS database. RPS creates a database called “RPSDB.” Click Next to continue with the installation setup. 5. After the SQL instance is established and the RPS database is created, the Installation Summary window opens.
RPS 3.3.3 Install RPS | en 23 Install the SQL Database and RPS Install the SQL Database The installation of the SQL database is automatic. No user interaction is needed. When the SQL database installation is complete, the RPS installation starts. Install RPS Use the following steps to install RPS: 1. 2. When the Welcome window opens, click Next. The Choose Destination Location window opens. If the default directory is acceptable, click Next.
en | Install RPS RPS 4. The Select Program Folder window opens. Click Next. 5. The Start Copying Files window opens. Click Next. The Setup Status window indicates the installer's progress. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS Install RPS | en 6. 25 When the InstallShield Wizard Complete window opens, click Finish. The computer restarts. 7. After logging onto the computer, start RPS by selecting Start>Bosch>RPS 5.x, or by double-clicking the RPS 5.x shortcut on the computer's desktop. 8. In the RPS Logon Information window, enter your RPS user name and password, then click OK. 9. – The default user name is admin – The default password is 1111 or default By default, the Panel List opens.
en | Install RPS 4998141259 | 12 | 2011.10 RPS Installation Guide Bosch Security Systems, Inc.
RPS 3.4 Install RPS | en 27 Use an Existing SQL Instance To use an existing SQL instance: 1. On the SQL Instance window, click the SQL Instances menu and select the appropriate SQL instance. 2. Authentication of the selected SQL instance starts. By default, Windows Authentication is used. If the authentication fails, you are prompted to use SQL Authentication. 3. To use SQL Authentication, check the SQL Authentication box, then enter your SQL user name and password in the respective fields.
en | Install RPS 4998141259 | 12 | 2011.10 RPS Installation Guide Bosch Security Systems, Inc.
RPS 3.5 Install RPS | en 29 Create a New SQL Instance To create a new SQL instance on the local RPS computer: 1. Select Local from the Select SQL Instance window. RPS creates a new SQL instance on the local computer that contains the following information: – SQL Instance Name: BOSCHSQL If BOSCHSQL is already used, the new instance is named BOSCHSQLn, where n = a number. For example, BOSCHSQL1.
en | Install RPS RPS 3.6 Automatic Installation of RPS 3.6.1 Overview When installing or upgrading to version 5.12 or later, RPS creates a file called RPSInstallation.ini. This file contains the SQL database settings that are selected when installing or upgrading RPS. After the first installation or upgrade of RPS, you can run the RPSInstallation.ini file to complete subsequent installations or upgrades that are identical to the first installation or upgrade. For more information, refer to: 3.6.
RPS 3.6.3 Install RPS | en 31 Use the RPSInstallation.ini File To use the RPSInstallation.ini file to install RPS with the same SQL database settings as the first installation: 1. Copy the following files to a blank CD-ROM: – – All files from the master RPS CD-ROM The RPSInstallation.ini file from the PC where the first installation or upgrade was performed (X:\RPSInstallation.ini, where “X” = the drive letter assigned to the computer’s local drive).
en | Install RPS 3.7 RPS View the Installation Log File During installation, RPS creates the RPSInstallation.log file, and logs the entire installation process in the file. This file is located in X:\RPS\Logs (“X” = the drive letter on the computer where RPS is installed). The log file contains the following: – All installation log entries with summary information – Database file transfer information – RPS database information Use the installation log file for troubleshooting purposes. 3.
RPS 4 Upgrade RPS | en 33 Upgrade RPS If you are using a version of RPS prior to RPS 5.7, automatic upgrading to RPS 5.12 or later is not supported. You must first uninstall the current version of RPS and peform a new installation to install the latest version of RPS. For more information on new installations, refer to Section 3 Install RPS, page 12. To preserve your database information from RPS 5.7 or earlier: 1. In RPS, select File>Backup. The Backup Filename dialog opens. In versions of RPS 3.
en | Upgrade RPS 4.1.2 RPS View the RPS Documentation and Start the Installation Process 1. Insert the RPS CD-ROM into your CD-ROM drive. The RPS startup program should automatically start. If the startup program does not automatically start: a. Select Start > Run… b. At the prompt, type: X:\setup.exe. "X" = the drive letter assigned to your CD-ROM drive. 2. When the startup window opens, select a language from the list provided. An instruction window opens in the selected language. 3.
RPS Upgrade RPS | en 35 Use the following steps to install RPS: 1. 2. When the Welcome window opens, click Next. The Choose Destination Location window opens. If the default directory is acceptable, click Next. Otherwise, click Browse to select a different directory, then click Next. 3. The Select Features window opens. Select the desired features and control panel types for this RPS installation, then click Next.
en | Upgrade RPS RPS 4. The Select Program Folder window opens. Click Next. 5. The Start Copying Files window opens. Click Next. The Setup Status window indicates the installer's progress. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS Upgrade RPS | en 6. 37 When the InstallShield Wizard Complete window opens, click Finish. The computer restarts. 7. After logging onto the computer, start RPS by selecting Start>Bosch>RPS 5.x, or by double-clicking the RPS 5.x shortcut on the computer's desktop. 8. In the RPS Logon Information window, enter your RPS user name and password, then click OK. 9. – The default user name is admin – The default password is 1111 or default By default, the Panel List opens.
en | Upgrade RPS 4998141259 | 12 | 2011.10 RPS Installation Guide Bosch Security Systems, Inc.
RPS Upgrade RPS | en 4.2 Upgrade RPS with a Microsoft Access Database 4.2.1 Before You Upgrade RPS 39 NOTICE! Use this procedure only if your RPS installation uses an Access database. If you are upgrading an RPS installation that uses a SQL database, refer to Section 4.1 Upgrade RPS with a SQL Database, page 33 for upgrade instructions. NOTICE! Before you upgrade RPS, back up your current RPS database and export a copy of it for recovery purposes, if needed.
en | Upgrade RPS RPS 4. Click Install to start the installation process. You are ready to prepare the installation of the SQL database and RPS. 4.2.3 Prepare the Upgrade for a Local SQL Database In this procedure, you are preparing the RPS upgrade to install the SQL database on the local RPS computer. 1. The SQL Instance window opens. Select an existing SQL instance, or create a new instance, and then click Next. For more information, refer to: – Section 3.
RPS Upgrade RPS | en – 41 If you need to change any settings, click Back to review and modify the previous installation setup windows as needed. – If you would like to print the installation summary, click Print. – If you are ready to install the SQL database and RPS, click Next. The installation process starts. See Section 4.2.5 Upgrade RPS, page 43 for more information. 4.2.
en | Upgrade RPS RPS – If you need to change any settings, click Back to move back through the installation setup windows as needed. – If you would like to print the installation summary, click Print. – If you are ready to install the SQL database and RPS, click Next. The installation process starts. See Section 4.2.5 Upgrade RPS, page 43 for more information. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS 4.2.5 Upgrade RPS | en 43 Upgrade RPS 1. 2. When the Welcome window opens, click Next. The Choose Destination Location window opens. If the default directory is acceptable, click Next. Otherwise, click Browse to select a different directory, then click Next. 3. The Select Features window opens. Select the desired features and control panel types for this RPS installation, then click Next.
en | Upgrade RPS RPS 4. The Select Program Folder window opens. Click Next. 5. The Start Copying Files window opens. Click Next. The Setup Status window indicates the installer's progress. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS Upgrade RPS | en 6. 45 When the InstallShield Wizard Complete window opens, click Finish. The computer restarts. 7. After logging onto the computer, start RPS by selecting Start>Bosch>RPS 5.x, or by double-clicking the RPS 5.x shortcut on the computer's desktop. 8. In the RPS Logon Information window, enter your RPS user name and password, then click OK. 9. – The default user name is admin – The default password is 1111 or default By default, the Panel List opens.
4.3 en | Upgrade RPS RPS Share the SQL Database If several networked computers share the SQL database, the first computer requires the RPS upgrade. After that, run RPS on the first computer to upgrade the existing SQL database before installing the new version of RPS on the other networked computers. During the database upgrade, the database files (.dat files) are moved from the shared database folder and merged into the SQL database.
RPS Upgrade RPS | en 4.4 Integrate the RPS Database Files into the SQL Database 4.4.1 Automatic Integration 47 In Versions 5.11 and lower, RPS uses a network drive to share database files (.dat files) among all of the RPS computers. In Versions 5.12 and later, RPS integrates the .dat files into the SQL database. The SQL database is then installed locally on the same computer that RPS is installed on, or it is installed on a network that all of the RPS computers can access.
en | Upgrade RPS 4.4.3 RPS Upgrade from RPS 5.11 or Lower If upgrading from RPS 5.11 or lower, the DAT Files Integration window opens when you click Upgrade Database on the File Locations tab. – If the path shown in the DAT Files Integration window matches the location of the RPS – If the path shown in the DAT Files Integration window does not match the path to where database files, click OK. the new SQL database is installed, click Browse, and navigate to the location of the new SQL database.
RPS 5 Log into RPS | en 49 Log into RPS NOTICE! Limit access to RPS to authorized individuals as it contains provisions for setting security passwords. Establish appropriate security levels and set passwords before allowing operating personnel access to RPS. 5.1 First Time Log-In NOTICE! Do not log into RPS as the same operator from two different PCs when using a networked database. To log into RPS: 1. Double-click the RPS shortcut icon that was placed on your desktop during installation.
5.2 en | Log into RPS RPS Change the Password To change the default password: 1. 2. From RPS, select Config>Password. When the Change Password dialog opens: a. Enter the old password. b. Enter the new password. c. Enter the new password again. d. Click OK. The new password takes effect the next time you log in. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS Maintenance | en 6 Maintenance 6.1 Set Security Levels by Panel Type for Networked Users 51 If your company is using a database on a networked drive and you want to allow users to be able to set security levels for control panels, you must copy the control panel definition files to each workstation on the network. This preserves the security settings you have set for each control panel type on the individual workstations on the network.
en | Maintenance RPS 6.2 Modify, Repair, or Remove RPS 6.2.1 Modify RPS NOTICE! To modify the current RPS installation, you must use the original installation files. – If RPS was installed from the CD-ROM, you must use the CD-ROM. – If RPS was installed from a folder containing the installation files, you must use the same folder in the location it resided at when RPS was installed.
RPS Maintenance | en 5. 53 Select the checkboxes for the features you want to install, or clear the checkboxes for the features you want to remove. 6. 7. Click Next. The selected features are either installed or uninstalled as selected. When the Install Complete dialog opens, click Finish to end the RPS Setup Maintenance process. 6.2.2 Repair RPS NOTICE! To repair the current RPS installation, you must use the original installation files.
en | Maintenance 6.2.4 RPS Remove RPS NOTICE! Only remove RPS if you do not intend on using RPS in the future. If you are using an unreleased version of RPS, such as an alpha or beta version, you must uninstall (remove) RPS before installing a released version. To remove RPS and all of its features: 1. Select Start > Settings > Control Panel > Add/Remove Programs. The Add/Remove Programs dialog opens. 2. Scroll down the list until you see RPS. Click RPS to select it. 3. Click Change/Remove.
RPS Maintenance | en 6.3 Revert to Previous RPS Installation After SQL Upgrade 6.3.1 Revert to a Previous SQL Database 55 NOTICE! The following procedure assumes that you used SQL Management Studio to back up the previous SQL database (creating a .bak file), and that the Database directory containing the .dat files was also backed up. 1. Select Control Panel > Add or Remove Programs, then uninstall the existing RPS installation. 2. Restart the PC. 3.
en | Maintenance RPS 7. When the Specify Backup dialog opens, click Add. 8. In the directory containing the SQL installation, select the .bak file, then click OK. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS Maintenance | en 9. 57 When the Specify Backup dialog identifies the Backup location, click OK. 10. Under Select the backup sets to restore, click the checkbox under Restore, then click OK. Bosch Security Systems, Inc. Installation Guide 4998141259 | 12 | 2011.
en | Maintenance RPS 11. The database restores successfully. Click OK. 12. Install the earlier version of RPS. During the installation process, when you reach the Select Database Configuration dialog, click Use Existing Database, then click Next. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS Maintenance | en 59 13. When the Use Existing Database dialog opens, click Browse and specify the location of the Access database. 14. Finish the installation by following the instructions on the screen. Bosch Security Systems, Inc. Installation Guide 4998141259 | 12 | 2011.
en | Maintenance 6.3.2 RPS Revert to a Microsoft Access Database NOTICE! The following procedure assumes that the Microsoft Access database from the previous installation was backed up, and that this Access database is already copied to the desired directory. 1. Select Control Panel > Add or Remove Programs, then uninstall the existing RPS installation. 2. Restart the PC. 3. Ensure that the backed-up database is not inside the RPS directory, then delete the RPS directory 4.
RPS 6.4 Maintenance | en 61 Recover Old Database Files NOTICE! You cannot point RPS to a database created in an older version of RPS. Doing so either produces errors, or it corrupts the database. To recover control panel accounts that were not exported before installing the new version of RPS: 1. Uninstall the new version of RPS. Refer to Section 6.2.4 Remove RPS on page 54. 2. Reinstall the old version of RPS (version 5.11 or earlier). 3.
6.5 en | Maintenance RPS Switch from a Client to a Network Installation It can be advantageous to place your RPS database files on a network drive so that many workstations can access a single database. 1. Start RPS, and log on when the RPS Logon Information dialog opens. 2. Select Config > System. The System Configuration dialog opens. 3. Select the File Locations tab. 4. In the Select or Enter SQL Server name field, select the name of the network SQL Server.
RPS Maintenance | en 5. 63 The Please re-login dialog opens. Click OK to restart RPS. When the database is shared on a network drive, two or more operators can access a single account. When an operator attempts to access an account that is already open by another operator (for example, one that has a different user name), a Panel Already Open dialog appears, indicating that the account is already opened for editing by another operator (the operator's log-in name displays in the message box).
6.6 en | Maintenance RPS Back Up the SQL or SQL Express Database 1. From the PC's Start > Programs menu, select Microsoft SQL Management Studio or Microsoft SQL Management Studio Express. 2. When the Connect to Server dialog opens, click Connect. 3. Right-click the RPS database, then select Tasks > Back Up.... 4. When the Back Up Database dialog opens, click OK. 4998141259 | 12 | 2011.10 Installation Guide Bosch Security Systems, Inc.
RPS Maintenance | en 5. 6.7 65 When the Backup Completed Successfully dialog opens, click OK. Install SQL Server Management Studio Express NOTICE! Networking protocols are disabled by default in SQL Server Express. If someone simply installs SQL Server Express and chooses all the defaults, SQL Server Express can only have connections originating on the local machine where SQL Server is installed.
en | Maintenance RPS NOTICE! Microsoft SQL Server Management Studio Express (SSMSE): In most cases, it is not necessary to install SSMSE. However, if needed, a copy of SSMSE is included on the RPS CD-ROM. Both a 32-bit version and 64-bit version of SSMSE is provided on the RPS CD-ROM. 1. On the RPS CD-ROM, open the SQL Express Management Studio Installation Files folder, and double-click the SQLServer2005_SSMSEE.msi file. 2. The SQL Server Management Studio Express Setup window opens. Click Next.
RPS Maintenance | en 4. 67 The Registration Information window opens. Click Next. 5. The Feature Selection window opens. Click Next. Bosch Security Systems, Inc. Installation Guide 4998141259 | 12 | 2011.
en | Maintenance RPS 6. The Ready to Install the Program window opens. Click Install. 7. 4998141259 | 12 | 2011.10 When the installation finishes, click Finish. Installation Guide Bosch Security Systems, Inc.
RPS Bosch Security Systems, Inc. Maintenance | en Installation Guide 69 4998141259 | 12 | 2011.
en | RPS Operation and Control Panel Account Notes RPS 7 RPS Operation and Control Panel Account Notes 7.1 RPS Notes 7.1.1 Installation and Administration When using the RAM II Exporter, use the Exporter R2X_V004.exe file. Do not use any other Ram2expt files 7.1.2 General Operation If your PC runs Windows XP Service Pack 2 or later and you use Windows Firewall, you must grant permission to RPS so it can conduct network communication with control panels: 1. Select Start > Control Panel.
RPS RPS Operation and Control Panel Account Notes | en 7.2 Control Panel Account Notes 7.2.1 2000 Series 71 RAM II Exporter version 004 does not import account notes and zone notes. The fields for these notes are empty in RPS. 7.2.2 D6412/D4412 and DS7240/DS7220 – Changing an RF ID: RPS allows you to change the RF ID for a location without resetting the learned characteristics for the transmitter. For example, the control panel supervises an RF3401 (RF3401E) Point Transmitter.
en | RPS Operation and Control Panel Account Notes – RPS Tamper conditions not bypassable (DS7240-UK only): Bypassing a zone from RPS only bypasses the alarm condition. Tamper conditions cannot be bypassed. – Remote Programming Lockout (DS7240-UK and DS7200V2-UK only): After three invalid attempts to connect to the control panel from RPS, the control panel locks out any remote programming sessions for 4 h. Remote programming through the direct connect method is still available.
RPS 7.2.6 RPS Operation and Control Panel Account Notes | en 73 DS7400XiV4-EXP – Phone Number Fields Also Apply to IP Addresses: The phone number fields in Phone Control and Partitions > Account Code also support IP addresses if you are communicating over an Ethernet network. – Resetting the Control Panel from RPS Clears Date and Time Settings: If you click the Reset Panel checkbox on the End Session dialog, RPS clears the control panel's date and time settings.
en | Index RPS Index Numerics 2000 Series Control Panel Notes 71 A Administration Installation and Administration Notes 70 Applicable Laws Software License Agreement 6 Authentication SQL 27 Windows 27 B Back Up the SQL or SQL Express Database 64 C Client Switch from a Client to a Network Installation 62 Contract Software License Agreement 7 Control Panel DS7400XiV4-EXP Notes 73 Control Panels 2000 Series Notes 71 D6412/D4412 Notes 71 D7024 Notes 72 D7212B1 Notes 72 D8112 Notes 72 D9112B1 Notes 72 D
RPS Index | en Integration Automatic Integration of the RPS Database Files into the SQL Database 47 Integrate the RPS Database Files into the SQL Database 47 Manual Integration of the RPS Database Files into the SQL Database 47 L Laws Export and applicable 6 Liability, limitation of Software License Agreement 6 License Software License Agreement 5 Local Install RPS with a Local SQL Database 12 Prepare Upgrade for a Local SQL Database 40 Switch from a Client to a Network Installation 62 Log Conversion Fil
en | Index RPS S Security Set Security Levels by Panel Type for Networked Users 51 Software License Agreement Entire Contract 7 Laws, export & applicable 6 Liability, limitation of 6 License 5 Ownership and Property Rights 5 Remedies 6 Rights, restricted 6 Taxes 6 Term and Transfer 7 Transfer of Ownership 5 U.S.
Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450 USA www.boschsecurity.com © Bosch Security Systems, Inc.
