Technical data

ManualsBrandsBosch ManualsDishwashersSHI 4302

BOSCH

Installation Instructions

for SHU (9900, 6800, 5300, 4300,

4000, 3300, 3030)

and SHI (6800, 4300)

and SHV (4800, 4300)

I I

Quick Reference Index

INTRODUCTION 2

TOOLS NEEDED FOR INSTALLATION 2

MATERIALS YOU WILL NEED 2

ACCESSORY PARTS SUPPLIED 2

TECHNICAL DATA

CHOOSING THE LOCATION

PREPARING THE LOCATION

HOT WATER SUPPLY

DRAIN HOSE

ELECTRICAL SUPPLY

INSPECTING THE DISHWASHER

PLACING THE DISHWASHER

DRAIN HOSE 6-7

CONNECTING HOT WATER SUPPLY 7

CONNECTING ELECTRICAL SUPPLY 8

GROUNDING INSTRUCTIONS 8

PANEL INSTALLATION, SHI MODELS 8-9

PANEL INSTALLATION, SHV MODELS 9

ACCESSORY PANEL INSTALLATION, SHU 9

DOOR TENSION ADJUSTMENT

FINAL CHECK LIST

IMPORTANT: Before you begin read these instructions completely and carefully.

INSTALLER: Please leave this manual with owner for future reference.

OWNER: Save these installation instructions for local electrical

inspector's use and for future reference.

Summary of content (11 pages)

PAGE 1
BOSCH Quick Reference Index Installation Instructions for SHU (9900, 6800, 5300, 4300, 4000, 3300, 3030) and SHI (6800, 4300) and SHV (4800, 4300) INTRODUCTION TOOLS NEEDED FOR INSTALLATION MATERIALS YOU WILL NEED ACCESSORY PARTS SUPPLIED 2 2 2 2 TECHNICAL DATA CHOOSING THE LOCATION PREPARING THE LOCATION HOT WATER SUPPLY DRAIN HOSE ELECTRICAL SUPPLY 4 4 4 4 INSPECTING THE DISHWASHER PLACING THE DISHWASHER DRAIN HOSE CONNECTING HOT WATER SUPPLY CONNECTING ELECTRICAL SUPPLY GROUNDING INSTRUCTIONS PA
PAGE 2
Introduction Please read these installation instructions completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance. sure to observe all listed warnings and cautions. Be These installation instructions are intended for use by qualified installers. In addition to these instructions the dishwasher shall be installed: * In the United States, in accordance with the National Electric Code/State and/or local codes.
PAGE 3
Technical Data 22-7/16' (570 mm I\ < 23-s/8' - 24' (600- 610 ram) 1-15/16" (49mm) Figure 4. If the dishwasher Figure 3. is to be installed sure there is adequate Figure 5. Dimensions A height 33-7/8" - 35" B width 23-9/16" clearance in a comer, make to open the door.
PAGE 4
Preparing the Location Openings for electrical, water and drain lines must be installed in the marked area as shown in Figures 6 and 7 to avoid interference with the dishwasher frame or other components. Shut-off valve ! I I I I /_ \ (520 ram) 23-5/8"- 24" (600 - 610 rnm) 3-1/2' Hot watersupplyline _ ,(90 mm) )_ 1-15/16. Figure 7. Electrical Supply Figure 6. Access holes must be rounded and smooth. Holes must not be larger than I'A" diameter.
PAGE 5
Inspecting the Dishwasher After unpacking the dishwasher and prior to installation thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately. Cosmetic damage must be reported within 5 days of installation. Mounting bracket bent lot mounting to side of cabinet Placing the Dishwasher The profile strips on the sides of the dishwasher allow the dishwasher to fit into a cabinet opening with a width of 23-5/8" (600 ram) to 24" (610 mm).
PAGE 6
Drain Hose Use the hose clamp and rubber connection hose, item "T" from accessory parts (see figure 2) to connect the drain hose to the sink, disposer or air gap. Hotwaterline lectric supplycable Figure 10. Figure 12. The access hole for the drain hose should be 1.25" (32 mm) diameter. Airgap Rubberconnector Entry mustbe abovetrap H_re 11. The rear leveling leg is adjusted by turning the center screw at the front of the dishwasher. The front leveling leveling legs are adjusted by rotating legs.
PAGE 7
Typical drain connections are shown in figures 12, 13 and 14. Figure 12 shows typical connection. Figures 13 and 14 show possible connections when an air gap is required. Connecting the Hot Water Supply Line The hot water supply line should be flushed to clear any foreign matefiai BEFORE connecting the dishwasher. Make sure there are no sharp bends or kinks which might restrict water flow.
PAGE 8
Connecting the Electrical Supply The electrical supply must be 120 volt, 60 Hz, 12 ampere, properly grounded. Connect with copper wire only. • • • ELECTRICAL SHOCK HAZARD DISCONNECT ELECTRICAL POWER AT THE CIRCUIT BREAKER BOX OR FUSE BOX BEFORE INSTALLING THE DISHWASHER. ELECTRICALLY GROUND DISHWASHER. USE COPPER CONDUCTORS ONLY. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT SERIOUS INJURY OR DEATH.
PAGE 9
Panel Installation, SHV Models If you have an SHV model, a fully integrated model, you will have additional mounting hardware and a folded template sheet with installation instructions comprised of pictograms. Refer to the folded template sheet for information on how to mount the panel. Please note that one side of the template shows how to mount a one piece panel and the other side of the template shows how to mount a two piece panel.
PAGE 10
SHU 9900 Handle Assembly The SHU 9900 model has a handle that needs to be 1/4" max. (6mm) assembled onto the door panel. Reference installation and instructions provided with the handle. kit Final check list CHECK ELECTRICAL REQUIREMENTS. BE SURE YOU HAVE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED GROUNDING METHOD. (586 mm' Turn on the hot water shut-off supply. Water temperature Operate the dishwasher plumbing leaks. valve and electrical should be 140°F (60°C).
PAGE 11
56 02 03 6207 (7910)