Quick instruction guide

8 9
START YOUR DISHWASHER
1. Press the On/O button.
2. Select a cycle and option if desired.
3. Press Start.
ADJUSTING THE SETTINGS
1. Press the On/O button. Hold down button A (see pages 6-7) and press
Start until the display shows š:‹x (x can be any number).
2. Release both buttons. The LED for the button A ashes and the digital
display shows the factory set value. Press A to choose the setting.
3. Press buttons B or C (up or down) to change the setting.
4. Press Start button to save the setting.
FREQUENTLY ASKED QUESTIONS
Q: Why is food left on dishes?
A: It is possible the dishes do not have adequate clearance between them.
Also, be sure nothing is blocking spray arm and that the lter is clean. Select an
intensive cleaning cycle.
Q: Why does the cycle run a long time?
A: 1. Sensors in the dishwasher automatically increase the cycle time to ensure a
good wash when heavy soil is detected.
2. Incoming water may not be hot enough and dishwasher has to heat it.
Q: Why is E:XX (X can be any number) displayed?
A: This is an error code. For example, E:22 indicates there is water in the sump
because the lter is blocked or needs cleaning. See the Use and Care Manual
for a list of error codes.
To access the full Use and Care Manual, go to:
www.bosch-home.com/us/service/get-support/owner-manuals.
MAINTENANCE TIPS
Clean surfaces with damp cloth and mild soap.
NOTICE: Do not use abrasives or bleach based cleaners. Do not use stainless
steel cleaner on black stainless or anti-nger print surfaces.
Clean the lter 3-12 times a year, depending on usage.
1. Unscrew the Large Object Trap as illustrated and remove the entire lter
system.
2. Remove the micro-lter from the ne lter, rinse the lters under running
water clean with a soft brush.
3. Reinstall the lter system in reverse sequence, align arrows.
1
2
Setting Factory setting Description
š-Intensive drying
š:‹‹-š:‹‚
š:‹‹/ o Improved drying for glasses and
plastic, by increasing the tempera-
ture and length.
§-Rinse Aid
§:‹†-§:‹‡
§:‹† Dispenses the amount of rinse aid,
which aects drying (see above).
›-Beep at cycle
end
›:‹‹-›:‹„
›:‹ƒ
Adjust the sound level of the signal
beep at the end of the cycle. Or turn
o (›:‹‹).
‚ -Infolight®
‚:‹‹-‚:‹‚
‚:‹‚ / on Light projected on the oor to signal
active wash cycle. Set to on or o.
˜-Auto power o
˜:‹‹-˜:‹ƒ
˜:‹‹/ unit does
not shut o
automatically
Unit turns itself o after cycle is com-
plete, either after 1 minute, ˜:‹‚ or
after 2 hours, ˜:‹ƒ.
max
vent
air
ADD RINSE AID
This dishwasher is designed to be used
with rinse aid, which enhances drying
results and shine.
• Add rinse aid before rst use and when
the Add Rinse Aid indicator light on the
control panel illuminates.
• Lift tab to open the rinse aid reservoir
and add liquid rinse aid into the oval
until it is full, avoiding air vent. Wipe up
any excess rinse aid that may puddle.
Tip: Remove lid of rinse aid bottle for easier pouring.
The amount of rinse aid dispensed can be set in 6 levels. Only change the
setting if streaks remain on the dishes (lower the amount), or if dishes are not
getting dry enough (increase the amount).