Installation Guide
Table Of Contents
- Dishwasher
- en-us
- Table of contents
- 1 IMPORTANT SAFETY INSTRUCTIONS
- 2 Before you begin
- 3 Installation Preparation
- 4 Installation Procedure
- 4.1 Attach Water Inlet Hose
- 4.2 Visual Leak Check
- 4.3 Pre-level the Dishwasher
- 4.4 Attach Power Cord
- 4.5 Mounting Brackets
- 4.6 Prepare Hoses and Power Cord
- 4.7 Install Dishwasher in Cabinet Space
- 4.8 Level the Dishwasher
- 4.9 Outer Door Assembly
- 4.10 Secure the Dishwasher
- 4.11 Attach the Standard Toe Panel
- 4.12 Attach Plastic Toe Panel
- 5 Dishwasher Connection
- 6 Customer Service
- fr-ca
- Table des matières
- 1 IMPORTANTES CONSIGNES DE SÉCURITÉ
- 2 Avant de commencer
- 3 Préparation avant l’installation
- 4 Procédure d’installation
- 4.1 Fixer le flexible d’arrivée d’eau
- 4.2 Contrôle visuel des fuites
- 4.3 Mise à niveau préalable du lave-vaisselle
- 4.4 Fixer le cordon d’alimentation
- 4.5 Équerres de fixation
- 4.6 Préparer les tuyaux et le cordon d’alimentation
- 4.7 Installer un lave-vaisselle dans un meuble
- 4.8 Mise à niveau du lave-vaisselle
- 4.9 Assemblage de la porte extérieure
- 4.10 Fixer le lave-vaisselle
- 4.11 Fixer la plinthe standard
- 4.12 Fixer la plinthe en plastique
- 5 Raccordement du lave-vaisselle
- 6 Service à la clientèle
- es-mx
- Tabla de contenidos
- 1 INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- 2 Antes de empezar
- 3 Preparación para la instalación
- 4 Procedimiento de instalación
- 4.1 Acoplar la manguera de entrada de agua
- 4.2 Comprobación visual de fugas
- 4.3 Nivelar provisionalmente el lavavajillas
- 4.4 Acoplar el cable de alimentación
- 4.5 Soportes de montaje
- 4.6 Preparar las mangueras y el cable de alimentación
- 4.7 Instalar el lavavajillas en el espacio del gabinete
- 4.8 Nivelar el lavavajillas
- 4.9 Montaje de la puerta exterior
- 4.10 Fijar el lavavajillas
- 4.11 Acoplar la placa protectora del zócalo estándar
- 4.12 Acoplar la placa protectora del zócalo de plástico
- 5 Conexión del lavavajillas
- 6 Servicio de atención al cliente
en-us Dishwasher Connection
14
3. If your model has a rubber apron, tuck it behind the tabs
on the metal brackets as shown.
4. Slide toe panel into position ensuring the bottom of the
toe panel is flush with the floor.
5. Use the 9/16" (14mm) toe panel screws to mount the
toe panel through the hole it matches up with on the
metal brackets.
The toe panel height can be adjusted by screwing into a
different hole in the bracket.
6. If your model has a rubber apron, open the door to
make sure that the apron is in the correct position.
Ensure the apron does not bind up and can freely move
up and down behind the toe panel.
4.12 Attach Plastic Toe Panel
If your dishwasher came with a plastic toe panel and
slotted toe panel, follow these instructions.
1. Align the plastic toe panel on the base of the
dishwasher so the holes lines up.
2. Attach using 2 of the included 3/4" (19mm) screws.
‒ Use only the included screws to avoid damaging the
dishwasher.
3. Slide the slotted toe panel into position ensuring that the
bottom of the toe panel is flush with the floor.
4. Screw the slotted toe panel into place with the
remaining 3/4"(19mm) screws.
Dishwasher Connection
5 Dishwasher Connection
Dishwasher Connection
Follow these instructions to connect the dishwasher.
5.1 Installing the Water Inlet Connection
The hot water heater should be set to deliver
approximately 120° F (49° C) water to the dishwasher.
Water that is too hot can cause some detergents to lose