Installation Guide
Table Of Contents
- Dishwasher
- en-us
- Table of contents
- 1 IMPORTANT SAFETY INSTRUCTIONS
- 2 Before you begin
- 3 Installation Preparation
- 4 Installation Procedure
- 4.1 Attach Water Inlet Hose
- 4.2 Visual Leak Check
- 4.3 Pre-level the Dishwasher
- 4.4 Attach Power Cord
- 4.5 Mounting Brackets
- 4.6 Prepare Hoses and Power Cord
- 4.7 Install Dishwasher in Cabinet Space
- 4.8 Level the Dishwasher
- 4.9 Outer Door Assembly
- 4.10 Secure the Dishwasher
- 4.11 Attach the Standard Toe Panel
- 4.12 Attach Plastic Toe Panel
- 5 Dishwasher Connection
- 6 Customer Service
- fr-ca
- Table des matières
- 1 IMPORTANTES CONSIGNES DE SÉCURITÉ
- 2 Avant de commencer
- 3 Préparation avant l’installation
- 4 Procédure d’installation
- 4.1 Fixer le flexible d’arrivée d’eau
- 4.2 Contrôle visuel des fuites
- 4.3 Mise à niveau préalable du lave-vaisselle
- 4.4 Fixer le cordon d’alimentation
- 4.5 Équerres de fixation
- 4.6 Préparer les tuyaux et le cordon d’alimentation
- 4.7 Installer un lave-vaisselle dans un meuble
- 4.8 Mise à niveau du lave-vaisselle
- 4.9 Assemblage de la porte extérieure
- 4.10 Fixer le lave-vaisselle
- 4.11 Fixer la plinthe standard
- 4.12 Fixer la plinthe en plastique
- 5 Raccordement du lave-vaisselle
- 6 Service à la clientèle
- es-mx
- Tabla de contenidos
- 1 INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- 2 Antes de empezar
- 3 Preparación para la instalación
- 4 Procedimiento de instalación
- 4.1 Acoplar la manguera de entrada de agua
- 4.2 Comprobación visual de fugas
- 4.3 Nivelar provisionalmente el lavavajillas
- 4.4 Acoplar el cable de alimentación
- 4.5 Soportes de montaje
- 4.6 Preparar las mangueras y el cable de alimentación
- 4.7 Instalar el lavavajillas en el espacio del gabinete
- 4.8 Nivelar el lavavajillas
- 4.9 Montaje de la puerta exterior
- 4.10 Fijar el lavavajillas
- 4.11 Acoplar la placa protectora del zócalo estándar
- 4.12 Acoplar la placa protectora del zócalo de plástico
- 5 Conexión del lavavajillas
- 6 Servicio de atención al cliente
en-us Before you begin
6
Coarse sandpaper
Parts
Elbow connection with 3/4"
female hose threads on one end
fits your water supply line on the
other.
Water inlet hose - minimum 3/8"
outer diameter copper tubing or
metal braided dishwasher supply
line.
* Both the elbow and the water
inlet hose can be found in the
dishwasher supply kit
SMZSH1ABUC.
Shut-off valve and fittings
appropriate for hot water supply
line.
2.4 Pre-install Checklist
Ensure that the following requirements are met when
planning the installation of your appliance.
WARNING
Avoid Scalding or Electric Shock Hazard
▶ Make sure the water supply and electrical supply are
shut off before installation or service.
▶ Do not allow the electrical and supply lines to touch.
¡ Select a location as close to the sink as possible for
easy access to water supply and drain lines.
¡ Be sure the unit is installed close enough to the sink so
the drain hose length does not exceed 92" (2337 mm)
and so that a portion of the drain hose is raised at least
33" above the floor level.
¡ Ensure that the enclosure is square and the opening is
at least 34" ( 863.3 mm) high and 24" (609.6 mm) wide.
¡ Check that the opening in the cabinet is large enough
for routing the electric cable, water line, and drain hose,
and if not, create a new opening. See
→
"Installation Preparation", Page7
¡ If the opening is wood, be sure it is sanded smooth. If it
is metal, be sure it is covered by a protective gasket.
¡ Be sure that your water heater set at 120° F (49° C)
and the water pressure measures at 15-145 psi (1-10
bar)
¡ Determine the mounting method based on the
dishwasher model and counter-top type. See
→
"Mounting Brackets", Page9
.
¡ Only use the included hardware for the installation. If
you are replacing a dishwasher, dispose of old hose
and other equipment properly.
¡ To avoid scratching the floor, have floor protection
ready for when the dishwasher will be slid into the
cabinet.
2.5 Electrical Requirements
Ensure that the following electrical requirements are met.
Dishwasher electrical rating
Volts 120
Hertz 60
Amperes 12
Watts 1,440 (max)
Electrical Supply
The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with all
national and local electrical codes and ordinances. The
dishwasher is designed for an electrical supply of 120V,
60 Hz, AC, connected to a dishwasher-dedicated, properly
grounded electrical circuit with a fuse or breaker rated 15
or 20 amps.
2.6 Cabinet Requirements
Ensure that the cabinet space for the installation meets
the required dimensions.