Installation Guide
Table Of Contents
- Dishwasher
- en-us
- Table of contents
- 1 IMPORTANT SAFETY INSTRUCTIONS
- 2 Before you begin
- 3 Installation Preparation
- 4 Installation Procedure
- 4.1 Attach Water Inlet Hose
- 4.2 Visual Leak Check
- 4.3 Pre-level the Dishwasher
- 4.4 Attach Power Cord
- 4.5 Mounting Brackets
- 4.6 Prepare Hoses and Power Cord
- 4.7 Install Dishwasher in Cabinet Space
- 4.8 Level the Dishwasher
- 4.9 Outer Door Assembly
- 4.10 Secure the Dishwasher
- 4.11 Attach the Standard Toe Panel
- 4.12 Attach Plastic Toe Panel
- 5 Dishwasher Connection
- 6 Customer Service
- fr-ca
- Table des matières
- 1 IMPORTANTES CONSIGNES DE SÉCURITÉ
- 2 Avant de commencer
- 3 Préparation avant l’installation
- 4 Procédure d’installation
- 4.1 Fixer le flexible d’arrivée d’eau
- 4.2 Contrôle visuel des fuites
- 4.3 Mise à niveau préalable du lave-vaisselle
- 4.4 Fixer le cordon d’alimentation
- 4.5 Équerres de fixation
- 4.6 Préparer les tuyaux et le cordon d’alimentation
- 4.7 Installer un lave-vaisselle dans un meuble
- 4.8 Mise à niveau du lave-vaisselle
- 4.9 Assemblage de la porte extérieure
- 4.10 Fixer le lave-vaisselle
- 4.11 Fixer la plinthe standard
- 4.12 Fixer la plinthe en plastique
- 5 Raccordement du lave-vaisselle
- 6 Service à la clientèle
- es-mx
- Tabla de contenidos
- 1 INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- 2 Antes de empezar
- 3 Preparación para la instalación
- 4 Procedimiento de instalación
- 4.1 Acoplar la manguera de entrada de agua
- 4.2 Comprobación visual de fugas
- 4.3 Nivelar provisionalmente el lavavajillas
- 4.4 Acoplar el cable de alimentación
- 4.5 Soportes de montaje
- 4.6 Preparar las mangueras y el cable de alimentación
- 4.7 Instalar el lavavajillas en el espacio del gabinete
- 4.8 Nivelar el lavavajillas
- 4.9 Montaje de la puerta exterior
- 4.10 Fijar el lavavajillas
- 4.11 Acoplar la placa protectora del zócalo estándar
- 4.12 Acoplar la placa protectora del zócalo de plástico
- 5 Conexión del lavavajillas
- 6 Servicio de atención al cliente
en-us Installation Procedure
8
1. Attach elbow joint to the water inlet valve with the open
end facing towards the direction of the sink, either to the
left or the right. . Turn by hand and do not over tighten
.
2. Attach hot water line to elbow.
3. Use two wrenches to tighten, using one to stabilize and
avoid putting stress on the water inlet valve.
4.2 Visual Leak Check
1. Temporarily hook up water supply under the sink by
going through the front of the sink cabinet. Do not turn
on the power or push the dishwasher into the niche.
2. Turn the water on and check for leaks at the water inlet
hose connection on the back of the dishwasher.
4.3 Pre-level the Dishwasher
Set the dishwasher to the correct height before it goes into
the cabinet.
1. Measure the height of the cabinet opening.
2. Raise the front of the dishwasher to approximately 1/2"
lower than the height of the opening by turning the feet
clockwise.
‒ You can raise the rear foot after the unit is in the
cabinet opening.
The maximum height the unit can be raised to is 34.5"
(867.3 mm)