3FHJTUFS ZPVS OFX #PTDI OPX XXX CPTDI IPNF DPN XFMDPNF %JTIXBTIFS FO *OTUSVDUJPO NBOVBM SK...
5HVHW VHF K % K PLQ $ K &
en Table of contents 8 Intended use . . . . . . . . . . . . . . ( Safety instructions . . . . . . . . . . Before you switch ON the appliance . . . . . . Delivery. . . . . . . . . . . . Installation. . . . . . . . . . In daily use . . . . . . . . . Door lock . . . . . . . . . . Button lock . . . . . . . . . Damage . . . . . . . . . . . Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
en Intended use 2 Cleaning and maintenance . . . Overall condition of the machine Special salt and rinse aid . . . . . . Filters . . . . . . . . . . . . . . . . . . . . . Spray arm . . . . . . . . . . . . . . . . . . 3 Fault, what to do? . . . . . . . . 22 . 22 . 22 . 23 . 23 8 Intended use dn en tI This appliance is intended for use in the home and domestic environments. Use the dishwasher only in the home and only for its designated purpose: for washing domestic dishes.
Safety instructions Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Before you switch ON the appliance Please read the instructions for use and installation carefully. They contain important information on how to install, use and maintain the appliance. Retain all documents for later use or for the subsequent owner. You can download the instructions for use from our website free of charge.
en Safety instructions If the dishwasher is installed below or above other domestic appliances, follow the information for installation in combination with a dishwasher in the installation instructions for the particular appliances. Also follow the installation instructions for the dishwasher to ensure that all appliances are operated safely.
Safety instructions Childproof lock (button lock) Butonlock You can secure your appliance from being unintentionally the programme terminated (e.g. improper operation by children). Activating the button lock: 1. Start the required programme. 2. Hold down the button + for approx. 4 sec. until this ’– is indicated on the digital display. If any button is pressed while the programme is running, this ’– is indicated on the digital display. It is not possible to end (Reset) the programme.
en Safety instructions m Warning Risk of injury! Knives and other utensils with sharp points must be placed in the cutlery basket with the points downwards or horizontally on the knife shelf*. Do not lean or sit on the open door. In the case of free-standing appliances, ensure that the baskets are not overloaded. * depending on model m Warning Risk of explosion! Do not add any solvents to the washing chamber.
Protection of the environment 7 Protection of the * Getting to know your environment onitceotPr het of Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials. Please dispose of the individual parts separated according to type. Please ask your dealer or inquire at your local authority about current means of disposal. Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g.
en Water softening system/Special salt + Water softening system/Special salt W reta ngnietofs laim cS ep/ty ss To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 1.2 mmol/l must be softened. The water is softened with special salt (regeneration salt) in the water softening system of the dishwasher.
Water softening system/Special salt Using special salt en Using detergents with salt component Det rgentswithsaltcompone t Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. 1. Open the screw-type cap of the compartment 12. 2. Fill the tank with water (only required when switching on the appliance for the first time). 3.
en Rinse aid , Rinse aid ensRi dia As soon as the rinse-aid refill indicator ` is lit on the fascia, there is still a rinse-aid reserve of 1-2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. 1.
Utensils Switching off rinse aid refill indicator If the rinse-aid refill indicator ` is impaired (e.g. when using combined detergents containing rinse aid component), it can be switched off. Proceed as described under “Setting amount of rinse aid” and set the value to §:‹‹. The rinse aid refill indicator ` is now switched off. - Utensils slinseUt Not suitable Cutlery and utensils made of wood. Delicate decorative glasses, craft and antique utensils. These decors are not dishwasher-proof.
en Utensils Unloading the dishwasher Cutlery basket Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled. You should always place cutlery unsorted with the points downwards. To prevent injuries, place long, pointed implements and knives on the knife shelf. Note When the programme ends, water droplets can still be seen inside the appliance. This does not affect the drying of the utensils.
Detergent . Detergent ntgereD te You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately large amount of active ingredients for all cleaning tasks. Modern, powerful detergents predominantly use a lowalkaline formulation with phosphate and enzymes. Phosphates bond the lime in the water.
en Detergent Tip If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate. Suitable detergents and care products can be purchased online via our website or via customer service (see back page). Combination detergent Apart from conventional detergents (Solo), a number of products are offered with additional functions.
Overview of programmes en / Overview of programmes m aogrm prseofw eviO rve The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
en Additional options Programme selection You can select a suitable programme according to the type of utensils and degree of soiling. Information for test institutes Test institutes receive the information for comparability tests (e.g. according to EN60436). These are the conditions for conducting the tests, however these are not the results or consumption values. Request by e-mail to: dishwasher@test-appliances.com The product number (E no.
Operating the appliance · Hygiene * en 1 Operating Hygien The temperature is increased during the cleaning process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. Ï Intensive zone * Intensive zone Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket.
en Operating the appliance Remaining running time display Switching off automatically after the end of the programme * Switchingof automaticalyafterthe ndoftheprogram e When the programme is selected, the remaining running time of the programme is indicated on the digital display h. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
Operating the appliance en Switching off the appliance Changing the programme Short time after the end of the programme: 1. Switch off ON/OFF switch (. 2. Turn off the tap (not applicable if Aqua-Stop fitted). 3. Remove the utensils when they have cooled down. When the START button H has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Note When the programme ends, leave the appliance to cool down a while before opening it.
en Cleaning and maintenance 2 Cleaning and maintenance ngniaeCl nda A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine Check spray arm for grease and limescale deposits. If you find such deposits: Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature.
Cleaning and maintenance Filters Spray arm The filters 1* keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system. Limescale and dirt from the rinsing water may block nozzles and the bearing assemblies of the spray arm 1". 1.
en Fault, what to do? 3 Fault, what to do? ,tF ula w tha ot Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. do ? In this case: 1. First disconnect the appliance from the power supply. 2. Remove the filters 1*. 3. Scoop out water, use a sponge if required. 4.
Fault, what to do? en Fault table Fault “Check water supply” display P lights up. Cause Supply hose kinked. Tap turned off. Tap jammed or calcified. Remedial action Install supply hose without kinks. Turn on the tap. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Fault code “:‚… is lit. Fault code “:‚† is lit. Fault code “:‚‡ is lit.
en Fault, what to do? Fault A different error code is indicated on the digital display. (“:‹‚ to “:„‹) Cause A technical fault has probably occurred. Display flashes. Door not closed properly. Refill indicator for salt X No rinse aid. and/or rinse-aid ` is lit. No salt. Sensor does not detect salt tablets. Refill indicator for salt X Refill indicator switched off. and/or rinse-aid ` is not lit. There is still enough special salt/ rinse aid available.
Fault, what to do? Fault Utensils not dry. Cause No or too little rinse aid in the dispenser. Programme selected without drying. Water collecting in depressions on the utensils and cutlery. en Remedial action Refill rinse aid. Select programme with drying (see Overview of programmes, Programme sequence). Arrange utensils in a sloping position, arrange affected utensils as sloping as possible. The combined detergent used has a poor drying performance.
en Fault, what to do? Fault Food remnants on the utensils. Cause Utensils placed too closely together, utensils basket overfilled. Spray arm rotation obstructed. Spray arm nozzles blocked. Filters 1* dirty. Filters 1* inserted incorrectly and/or not engaged. Rinse programme too weak. Utensils precleaned too intensely; sensors therefore decide on weak programme sequence. Stubborn soiling cannot be completely removed. Tall narrow receptacles in corner areas are not rinsed adequately.
Fault, what to do? Fault Washable or water-soluble coatings in the container or on the door. White, stubborn coatings; limescale on the utensils, container or door. Cause Detergent substances are deposited. These coatings cannot usually be removed with chemicals (appliance cleaner, ...). If there is a “white coating” on the container floor, the water softening system has been set marginally. Salt dispenser cover 12 not closed. Only for glasses: Initial glass corrosion – can only apparently be wiped off.
en Fault, what to do? Fault Coloured (yellow, orange, brown), easily removable deposits inside the appliance (mainly in the floor area). Plastic parts discoloured. Removable streaks on glasses, glasses with metallic appearance and cutlery. Initial or existing, irreversible clouding of glass.
Fault, what to do? Fault Rust spots on the cutlery. The appliance does not start. Programme starts automatically. Appliance cannot be set (hardness, final rinse, ...). The door is difficult to open. Door cannot be closed. Cover on the detergent dispenser cannot be closed. Detergent residue in the detergent dispenser. Appliance stops in the programme or programme is interrupted. Cause Cutlery not adequately rustresistant. Knife blades are frequently more severely affected.
en Fault, what to do? Fault Filling valves making striking noises. Knocking or rattling noise. Unusual foam formation. 32 Cause Depends on domestic installation, as appliance is not defective. No effect on appliance function. If there is a low load, the water jets strike the washing tank directly. Light utensils move during the wash cycle. Handwash liquid in the rinse aid dispenser. Rinse aid spilled. Remedial action No remedial action possible.
Customer service 4 Customer service om C rteus 5 Installation and connection ecv ires If you are unable to rectify the fault, please contact your customer service. We always find a suitable solution, even to avoid unnecessary visits by technicians. Contact information for your nearest customer service can be found on the back of these instructions for use or on the enclosed customer service list. When calling, please state the appliance number (ENr.
en Installation and connection Delivery Installation Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle. The required installation dimensions can be found in the installation instructions. Level the appliance. Ensure that the appliance is situated securely on the floor. The appliance can easily be installed in a fitted kitchen between wooden and plastic walls.
Installation and connection en Drinking water connection Warm water connection * 1. Fasten the drinking water connection to the tap according to the installation instructions using the enclosed parts. Ensure that the drinking water connection is not kinked, crushed or twisted. 2. When replacing the appliance, always use a new water supply hose. Water pressure: At least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
en Installation and connection Electrical connection Connect the appliance to an alternating current only, ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor. See rating plate for required fusing 1b. The socket must be near the appliance and freely accessible following installation.
&KLOGSURRI ORFN GRRU ORFN â 7R RSHQ WKH GRRU PRYH OHYHU WR ULJKW DQG SXOO GRRU KDQGOH $OZD\V FORVH WKH DSSOLDQFH GRRU FRPSOHWHO\ ZKHQ \RX OHDYH WKH DSSOLDQFH 7KLV LV WKH RQO\ ZD\ \RX FDQ SURWHFW \RXU FKLOGUHQ IURP SRWHQWLDO GDQJHUV
$TXD6WRS JXDUDQWHH EPFT OPU BQQMZ UP BQQMJBODFT XJUIPVU "RVB4UPQ *O BEEJUJPO UP XBSSBOUZ DMBJNT BHBJOTU UIF TFMMFS CBTFE PO UIF QVSDIBTF DPOUSBDU BOE JO BEEJUJPO UP PVS BQQMJBODF XBSSBOUZ XF XJMM QBZ EBNBHFT VOEFS UIF GPMMPXJOH DPOEJUJPOT *G PVS "RVB4UPQ TZTUFN JT EFGFDUJWF BOE DBVTFT XBUFS EBNBHF XF XJMM NBLF HPPE UIF EBNBHF GPS QSJWBUF VTFST 5P FOTVSF XBUFS EBNBHF QSPUFDUJPO UIF BQQMJBODF NVTU CF DPOOFDUFE UP UIF QPXFS TVQQMZ 5IJT MJBCJMJUZ HVBSBOUFF JT WBMJE GPS UIF TFSWJDF MJGF PG UIF
