Register your new Bosch now: http://www.bosch-home.co.
Thank you for buying the “Sensixx’x Di90” compact steam iron from Bosch. Carefully read through the operating instructions for the appliance and safeguard them for future reference. You can download this manual from the local home pages of Bosch. General safety instructions ❐❐ The iron must not be left unattended while it is connected to the General safety instructions 2 Description 4 supply mains. Using your appliance 5 ❐❐ Remove the plug from1.
Important notices • This appliance has been designed exclusively for normal household use in a home environment.. • This appliance must be used only for the purposes for which it was designed, i.e. as an iron. Any other use will be considered improper and consequently dangerous. The manufacturer will not be held responsible for any damage arising from misuse or improper use. • This appliance is to be connected and used in accordance with the information stated on its characteristics plate.
Description 1. Motor activation trigger * 2. “SensorSteam” indicator lamp 3. “SET” button 4. Steam setting indicator lamps 5. Spray button 6. Shot of steam button 7. Water inlet lid 8. Spray nozzle 9. Level mark for maximum filling 4 B O S CH 10. Soleplate 11. “clean” button 12. Temperature index 13. Temperature control with “TempOK” indicator 14. “MotorSteam” indicator lamps 15. Heel 16.
Using your appliance 1. Filling the water tank This appliance has been designed to use normal tap water. Important: Do not use additives! The addition of other liquids, such as perfume, vinegar, starch, condensation water from tumble dryers or from air conditioning systems or chemicals will damage the appliance. Any damage caused by the use of the aforementioned products will make the guarantee void! 1 Unplug the iron from the mains. 2 Open the water inlet lid (7). 3 Fill the water tank.
3. Setting the temperature Set the temperature control (13) to the corresponding position by lining it up with the temperature index (12) on the iron. Temperature ● ●● ●●● max Suitable for synthetics silk – wool cotton linen Tip: Start by ironing the fabrics that require the lowest ironing temperature. Check the recommended ironing temperature on the label on the garment.
4. “SensorSteam” function After the initial heating, “SensorSteam” function switches off the iron when it is left unattended, thus increasing security and saving energy. 1 2 While the handle is gripped, the iron heats up. The “SensorSteam” indicator lamp (2) will remain lit continuously. When the handle is released, the “SensorSteam” function is activated. The “SensorSteam” indicator lamp (2) will flash. 5. Steam settings This iron generates steam by means of a built-in motor.
7. Vertical steam Vertical steam can be used to remove creases from hanging clothes, curtains etc. 10 cm / 4 in 1 2 3 Set the temperature control (13) to “max”. Hang article of clothing on a clothes hanger. Operate the iron in a vertical position at a distance of 10 cm / 4 in, and press the shot of steam button (6) repeatedly with pauses of at least 5 seconds. 8. Spray Spray can be used to remove stubborn wrinkles.
Cleaning & Maintenance EEAttention! Risk of burns! Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it. 1 If the iron is only slightly soiled, pull out the plug and allow the soleplate (10) to cool down. Wipe the housing and the soleplate with a damp cotton cloth only. 2 To keep the soleplate smooth, you should avoid hard contact with metal objects. Never use a scouring pad or chemicals to clean the soleplate.
3 4 Plug in the iron and set the temperature to “max”. When the lamp “TempOK” (13) remains lit continuously, unplug the iron (very important!). 5 6 Hold the iron over a sink. Press the “clean” button (11) and shake the iron back and forth keeping it in a horizontal position until approximately one third of the water capacity of the tank is evaporated. Boiling water and steam will come out, carrying scale or deposits that might be there.
Trouble shooting Problem Probable cause Solution The iron does not heat up. The “SensorSteam” function has been activated. The iron is set to stand-by. Grip the handle of the iron to re-start it. Water drips out of the soleplate when using the “shot of steam” function. You have pressed the shot of steam button (6) repeatedly without waiting for 5 seconds between each press. Wait 5 seconds between each press of the shot of steam button. Steam does not come out in horizontal position.
Customer Service Great Britain Bosch Customer Service Grand Union House Old Wolverton Road Milton Keynes MK12 5PT 002 Di90 GB i-Temp / AntiShine / Hygienic 09/17 9001183792 UK +44 (0)344 892 8979 IRL +353 (0)1450 2655 www.bosch-home.co.
