Bosch 20-inch High-resolution LCD Monitor UML-202-90 en Instruction Manual
UML-202-90 Table of Contents | en iii Table of Contents 1 Safety 1 1.1 Important Safety Instructions 1 1.2 Safety precautions 3 1.3 Important notices 4 1.4 Customer Support and Service 8 2 Unpacking 9 2.1 Parts List 9 3 Exploded View 10 4 Remote Control 12 4.1 Remote Control Battery Installation 13 5 Description 14 5.1 Features 14 5.2 Power 14 6 Installing the UML-202-90 15 6.1 Ventilation 15 6.2 Mounting the UML-202-90 15 6.2.
iv en | Table of Contents UML-202-90 8.2 LED Indicator 26 9 TroubleShooting Guide 27 10 Maintenance 28 11 Technical Specifications 29 F01U076723 | 1.0 | 2007.09 Instruction Manual Bosch Security Systems, Inc.
UML-202-90 Bosch Security Systems, Inc. Table of Contents | en Instruction Manual v F01U076723 | 1.0 | 2007.
1 en | Safety UML-202-90 1 Safety 1.1 Important Safety Instructions Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit. 1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist fluff-free cloth or leather shammy may also be used.
UML-202-90 Safety | en – 2 For limited power source units, this power source must comply with EN60950. Substitutions may damage the unit or cause fire or shock. – For 24 VAC units, voltage applied to the unit's power input should not exceed ±10%, or 28 VAC. User-supplied wiring must comply with local electrical codes (Class 2 power levels). Do not ground the supply at the terminals or at the unit's power supply terminals.
3 1.2 en | Safety UML-202-90 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: ! Indicates a potentially hazardous situation. If not avoided, this could result in serious bodily injury or death. CAUTION! Medium risk: ! Indicates a potentially hazardous situation.
UML-202-90 1.3 Safety | en 4 Important notices Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury and/or serious damage to the unit. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use caution and care when moving the cart/apparatus combination to avoid injury from tip-over.
5 en | Safety UML-202-90 Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive force or shock may damage the unit and the hard disk drives. Outdoor signals - The installation for outdoor signals, especially regarding clearance from power and lightning conductors and transient protection, must be in accordance with NEC725 and NEC800 (CEC Rule 16-224 and CEC Section 60).
UML-202-90 Safety | en 6 FCC & ICES INFORMATION (commercial applications) (U.S.A. and Canadian Models Only) This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: – this device may not cause harmful interference, and – this device must accept any interference received, including interference that may cause undesired operation.
7 en | Safety UML-202-90 Disclaimer Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested fire, shock and/or casualty hazards as outlined in UP’s Standard(s) for Safety for Information Technology Equipment, UL 60950-1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product.
UML-202-90 1.4 Safety | en 8 Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers USA Telephone: 800-366-2283 or 585-340-4162 Fax: 800-366-1329 Email: cctv.repair@us.bosch.com Customer Service Telephone: 800-289-0096 Fax: 585-223-9180 Email: security.sales@us.bosch.com Technical Support Telephone: 800-289-0096 Fax: 585-223-3508 or 717-735-6560 Email: technical.support@us.
UML-202-90 2 Unpacking | en 9 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
10 3 en | Exploded View UML-202-90 Exploded View Fig. 3.
UML-202-90 Exploded View | en 11 1 2 3 4 5 6 7 9 8 10 11 12 13 14 15 16 17 18 Fig. 3.
12 en | Remote Control 4 UML-202-90 Remote Control This section details the functions and the usage of the Bosch remote control. Button Function POWER Turns the power ON and OFF. SOURCE Selects the PC or Video source. Numbers Numerals 0-9. AUTO Auto adjusts to the graphics adaptor. MUTE Mutes the sound. MENU Displays the OSD. Pressing the MENU button returns you to the Main menu from anywhere in the OSD menus. EXIT Exits the OSD. UP Moves the cursor up in an OSD menu.
UML-202-90 Remote Control | en 4.1 13 Remote Control Battery Installation 1. Turn the remote over (buttons facing down) and push down on the cover and slide it off. 2. Insert two (2) new AAA alkaline batteries, matching the batteries to the (+) and (-) marks inside the battery case. Fig. 4.1 Battery Installation 3. i Slide the battery cover back into place. NOTICE! Replace batteries when required or at least once a year. Dispose of used batteries properly. Bosch Security Systems, Inc.
14 5 en | Description UML-202-90 Description The UML-202-90 20-inch (51-cm) Color Panel Display Monitor displays PAL or NTSC standard color pictures in CCTV systems. The UML-202-90 monitor includes two (2) looping Composite Video BNC connector inputs, two (2) looping Audio input RCA, and two (2) looping Y/C (SVideo) input using a 4-pin mini-DIN.
UML-202-90 Installing the UML-202-90 | en 6 15 Installing the UML-202-90 This chapter outlines the procedures needed to install the UML-202-90 Series. A qualified service person should install the monitor and adhere to all local codes. The UML-202-90 monitor is delivered with a 3-pole US-style power cord and a 3-pole Eurostyle power cord. Use the US-style power cord where 120 VAC, 60 Hz power is available; and use the Euro-style power cord where 230 VAC, 50 Hz power is available.
16 en | Installing the UML-202-90 6.2.2 UML-202-90 Wall Mount Installation The square mounting holes (100 mm (3.9 in.) centers) can be used for wall mount installation using the optional UMM-LW-20B fixed mount or the UMM-LW-30B swivel/tilt mount. Fig. 6.1 Mounting the Device 6.
UML-202-90 6.4 Installing the UML-202-90 | en 17 Connecting the Y/C (S-Video) Signal to the Monitor There is one (1) mini-DIN type connector for the S-Video (Y/C) input (see Figure 6.2 on page 17) on the rear side panel. NOTE: Both Y and C inputs are terminated with 75 ohm. Fig. 6.2 Y/C Connection Pinout 6.5 Reference Input 1 GND 2 GND 3 Y-signal IN or OUT 4 C-signal IN or OUT Connecting Audio to the Monitor There are two (2) sets of mono audio connectors for audio input.
18 en | Installing the UML-202-90 6.6.2 UML-202-90 DVI The monitor can be connected by using the supplied DVI-D cable and connecting it to the digital DVI-D signal. Fig. 6.4 DVI Input 6.6.3 VGA The monitor can be connected by connecting the analog VGA signal by using the provided VGA cable (D-SUB to D-SUB). Fig. 6.
UML-202-90 6.7 Installing the UML-202-90 | en 19 Single / Multiple Monitor Configuration Fig. 6.6 Single Monitor Configuration Reference # Description 1 Video Camera 2 VIDEO 2 (AV2) IN 3 VIDEO 2 (AV2) OUT 4 VCR Fig. 6.7 Multiple Monitor Configuration Reference # Description 1 Video Camera 2 VIDEO 2 (AV2) IN 3 VIDEO 2 (AV2) OUT Bosch Security Systems, Inc. Instruction Manual F01U076723 | 1.0 | 2007.
20 en | Navigating the Monitor UML-202-90 7 Navigating the Monitor 7.1 Navigating the Front Panel Use the front panel to make any necessary OSD adjustments to the UML-202-90. See the figure below for an explanation of the front panel. Fig. 7.
UML-202-90 Navigating the Monitor | en 7.2 21 Navigating the Monitor On-screen Display (OSD) The UML-202-90 has two (2) modes, Video and PC. The UML-202-90 is programmed through the on-screen display (OSD) menus. Each OSD shows a list of parameters or submenus that the operator can select. To access the OSD menus, press the Menu button on the front panel or on the remote control. Use the front panel of the UML-202-90 or remote control to make any necessary adjustments to the OSD.
22 7.4 en | Navigating the Monitor UML-202-90 Custom Menu To access the Custom menu, press the Menu button on the front panel of the monitor. Next, press the right arrow and then press the up and down arrows to select a submenu. Press the left and right arrow buttons to increase or decrease the values. When finished, press the Menu button to save any changes, then press the Menu button again to exit the OSD. Custom Brightness Contrast Color Tint Sharpness :Move 50 50 50 50 20 :Input :Menu Fig. 7.
UML-202-90 7.5 Navigating the Monitor | en 23 Picture / Sound Menu To access the Picture / Sound menu, press the Menu button on the front panel of the monitor, then press the left and right arrows to select the Picture / Sound icon. Press the up and down arrows to select the Picture / Sound submenu. Picture / Sound Picture Mode Color Tone Mute Volume Size NR :Move Custom Normal Off 20 4.3 On :Input :Menu Fig. 7.
24 en | Navigating the Monitor UML-202-90 Size (Video Mode) Selects the Aspect Ratio Control mode. Choices are: 4:3, Panorama, Zoom1, Zoom2, Wide. NR (Video Mode) Turns Noise Reduction on or off. Turning this feature OFF reduces the video quality slightly, but improves the monitors response time to MOTION. PC (PC Mode) Selects between Auto or manual adjustment of the desktop screen. Auto Adjust: Auto synchronizes screen to graphics adaptor.
UML-202-90 Navigating the Monitor | en 7.7 25 Setup Menu To access the Setup menu, press the Menu button on the front panel of the monitor, then press the left and right arrows to select the Setup icon. Press the up and down arrows to select the Setup submenu. Setup Reset Language OSD Tone Blue Screen Key Lock Firmware Version :Move :Input English Blue Off Off 1.2 :Menu Submenu Definition Reset Restores default settings. Language Adjusts the language of the OSD.
26 8 en | Power Management UML-202-90 Power Management This monitor features a power management system to “power down” upon receipt of the display power management signaling (DPMS) from a DPMS video card. The DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system. 8.1 8.
UML-202-90 9 TroubleShooting Guide | en 27 TroubleShooting Guide Problem Solution No image is displayed on 1. Check that the power cord of the monitor is securely con- screen nected into the wall outlet or grounded extension cable or strip. 2. 3. Power switch should be in the ON position and the LED lit. Check that the Brightness and/or Contrast adjustments of the display have not been turned down to minimum levels. “Going to Sleep” mes- 1.
28 en | Maintenance 10 UML-202-90 Maintenance To clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or a soft lint-free cloth. Staining and discoloration may occur if left on the panel for long periods. If the surface (polarizer) of the LCD panel is dirty or stained, use absorbent cotton or a soft lint-free cloth to remove the residue as follows: 1. 2. Turn off the computer or display. Do not spray any liquid directly on the screen.
UML-202-90 11 Technical Specifications | en 29 Technical Specifications Electrical Rated Voltage 110/230 VAC, 50/60 Hz Voltage Range 90 to 264 Power at Rated Voltage 70 W Sync Format PAL/NTSC LCD Panel TFT LCD Screen Size (H x V) 408 x 306 mm (16 x 12 in.) Viewable Picture Area 20.1 in. (53 cm) measured diagonally Pixel Pitch (H x V) 0.255 x 0.255 mm (0.01 x 0.01 in.) Resolution 1600 x 1200 pixels, 500 TV lines typical Aspect Ratio 4:3 Display Colors 8-bit interface; 16.
30 en | Technical Specifications UML-202-90 HDMI/DVI/RGB Inputs Analog RGB 0.7 Vp-p (0.
UML-202-90 Technical Specifications | en 31 Connectors Video 1 Composite video: two (2) BNC (1 in, 1 out) Video 2 Composite video: two (2) BNC (1 in, 1 out) Y/C (S-Video) Two (2) mini-DIN, 4-pin (1 in, 1 out) Component Y, Pb, Pr Audio PC: one (1) 1/8 in. mini phono plug Video: four (4) RCA (2 in, 2 out) DVI-D HDMI RGB One (1) DVI to DVI cable included One (1) cable not included One (1) RGB to RGB cable included Power Cord Two (2) 3-wire with a grounded plug, 1.
Americas: Bosch Security Systems 130 Perinton Parkway Fairport, New York, 14450 USA Phone +1 800 289 0096 Fax +1 585 223 9180 www.boschsecurity.us Europe, Middle East, Asia: Bosch Security Systems B.V. Postbus 80002 5600 JB Eindhoven Phone: +31 40 2577 200 Fax: +31 40 2577 202 nl.securitysystems@bosch.com www.boschsecurity.nl www.boschsecurity.com © Bosch Security Systems, Inc., 2007; F01U076723 | 1.0 | 2007.09 www.boschsecurity.com Asia-Pacific: Bosch Security Systems Pte Ltd.