UMS Series Public View Monitor UMS-20xxxA and UMS-20xxxC en Installation Manual
en Important Safeguards 1. Read, Follow, and Retain Instructions - All safety and operating instructions should be read and followed before operating the unit. Retain instructions for future reference. 2. Heed Warnings - Adhere to all warnings on the unit and in the operating instructions. 3. Attachments - Attachments not recommended by the product manufacturer should not be used, as they may cause hazards. 4. Installation Cautions - Do not place this unit on an unstable stand, tripod, bracket, or mount.
iv en For Indoor Product WARNING: 1. Water and Moisture - Do not use this unit near water for example, in a wet basement, in an unprotected outdoor installation or in any area classified as a wet location. Electrostatic-sensitive device. Use proper CMOS/ MOSFET handling precautions to avoid electrostatic discharge. 2.
en FCC & ICES INFORMATION v Safety Precautions (U.S.A. and Canadian Models Only) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.
vi en INFORMATIONS FCC ET ICES Sécurité (modèles utilisés aux États-Unis et au Canada uniquement) Attention : l'installation doit exclusivement être réalisée par du Ce produit est conforme aux normes FCC partie 15.
en vii AVERTISSEMENT: cet appareil est sensible aux décharges électrostatiques. Pour éviter tout risque de décharge électrostatique, observez les précautions de manipulation du CMOS/MOSFET appropriées. REMARQUE : lors de la manipulation des cartes à circuits imprimés sensibles aux décharges électrostatiques, portez des bracelets antistatiques mis à la terre et observez les consignes de sécurité relatives aux décharges électrostatiques.
viii en Bosch Security Systems, Inc. F01U029703 | 1.0 | 2006.
UMS Series Public View Monitor | en ix Preface This guide describes how to install and configure the UMS Series Public View Monitor. Audience This guide is intended for qualified installation and service personnel who are familiar with the applicable national and local electrical codes. Document Conventions Convention Bold Bold Italic Underline Meaning Denotes a part, item, or assembly. Denotes a reference to another paragraph, figure or table. Used to emphasize a point.
x en | F01U029703 | 1.0 | 2006.07 UMS Series Installation Manual Bosch Security Systems, Inc.
UMS Series Public View Monitor Table of Contents | en xi Table of Contents 1 Unpacking 1 1.1 Parts List 1 2 Description 2 2.1 General Features 2 2.2 UMS Series Models 2 3 Installing the UMS Series 3 3.1 Power 3 3.2 Mounting 3 3.3 Power Connection 4 3.4 Video Connections 4 3.5 Remote Control Battery Installation 5 4 Monitor Remote Control Functions (Bosch) 6 4.1 Monitor Remote Control Operating Modes 7 4.2 Navigating the Monitor On-screen Display (OSD) 7 4.
xii 9 en | Table of Contents UMS Series Public View Monitor Troubleshooting 21 9.1 Make adjustments to the control board and option switches 21 9.2 Screen flickers 22 9.3 No video displayed 23 9.4 Only displays Power Save mode 23 9.5 Remote control does not activate the monitor 24 9.6 Lost remote control 24 9.7 Memory card images appear stretched and out of proportion 25 9.8 Images are smaller than the recommended size 25 9.
UMS Series Public View System 1 Unpacking | en 1 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper. Verify that all parts shown in the Parts List are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit. Save it for possible future use. 1.
2 2 en | Description UMS Series Public View System Description The Universal Monitor System (UMS) Series provides video surveillance and advertising display in one system. It contains an LCD display, a hidden CCTV camera, a built-in memory card reader*, and motion and light sensors. The UMS 20xxxC Series, with an optional integrated memory card reader, displays images from a Flash memory card reader.
UMS Series Public View System 3 Installing the UMS Series | en 3 Installing the UMS Series This section provides instructions for installing and configuring the UMS Series. ! 3.1 3.2 CAUTION! Installation should be performed by qualified service installers only, using construction methods in accordance with applicable local codes and standards. Power Model Rated Voltage Voltage Range Power at Rated Voltage Sync.
4 en | Installing the UMS Series UMS Series Public View System Ref. # Description 1 2.95-in. (75-mm) mounting hole pattern 2 3.94-in. (100-mm) mounting hole pattern 3 Thumbscrews 4 Sign mounting hole pattern (To mount a sign, use #8-32 screws with a maximum length of 5/16 in.
UMS Series Public View System 3.5 Installing the UMS Series | en 5 Remote Control Battery Installation 1. Turn the remote over (buttons facing down) and push down on the cover and slide it off. 2. Insert two (2) new AAA alkaline batteries, matching the batteries to the (+) and (-) marks inside the battery case. Fig. 3.2 Battery Installation 3. i Slide the battery cover back into place. NOTICE! Replace batteries when required or at least once a year. Dispose of used batteries properly.
6 4 en | Monitor Remote Control Functions (Bosch) UMS Series Public View System Monitor Remote Control Functions (Bosch) This section details the functions and the usage of the Bosch remote control. Button Function AUTO Switches between images from the auxiliary video to the surveillance video when motion is detected. The auxiliary video source for each mode is: UMS-20xxxA: Video In UMS-20xxxB: Memory card reader MEM Saves current operating mode during Sleep mode or power failures.
UMS Series Public View System 4.1 Monitor Remote Control Functions (Bosch) | en 7 Monitor Remote Control Operating Modes There are three (3) operating modes for the UMS Series: – AUTO: The UMS switches between images from an auxiliary (external) video source to surveillance video when motion is detected. – AUX: The UMS displays only images stored on a memory card or from the external video source. – 4.2 CAM: The UMS monitor displays only surveillance (internal camera) video.
8 en | Monitor Remote Control Functions (Bosch) 4.3.1 UMS Series Public View System Video Menu The Video menu allows you to customize the screen by adjusting the Sharpness, Brightness, Backlight, Contrast, Color, and Tint from a range of 0-100 . Fig. 4.
UMS Series Public View System 4.3.3 Monitor Remote Control Functions (Bosch) | en 9 Misc. Menu The Misc. menu allows you to verify information about the unit, reset the settings to the factory default, and edit the display and OSD. Fig. 4.3 Misc. Menu Example i 4.
10 en | Using the Card Reader 5 UMS Series Public View System Using the Card Reader UMS-20xxxC models contain a card reader that allows you to expand the number of JPEG images displayed on the UMS monitor. 5.1 Compatible Flash Memory Cards A flash memory card is a compact, portable recording medium with a data capacity that exceeds the capacity of a floppy disk. Select UMS models have four (4) different multimedia ports wired into the AUX Video Input.
UMS Series Public View System 5.2.2 Using the Card Reader | en 11 Inserting the Flash Memory Card (not provided) 1. Insert a compatible memory card all the way into the appropriate port located on the back of the UMS. To ensure a proper playback, you must insert the memory card correctly. 1 2 3 4 Fig. 5.1 Card Reader Insertion Ref.
12 en | Card Reader Remote Control Functions (SanDisk®) 6 UMS Series Public View System Card Reader Remote Control Functions (SanDisk®) This section details the functions and the usage of the card reader remote control for the UMS-20xxxC models.
UMS Series Public View System i 6.2 Card Reader Remote Control Functions (SanDisk®) | en13 NOTICE! The effects (called Transition Effects) that the card reader displays between images are randomly generated and cannot be changed. Card Reader Menu Selections There are seven (7) on-screen main menus which allow you to customize your settings. 6.2.1 Select Memory Card Menu The Select Memory Card menu allows you to choose the memory card you would like to access. Fig. 6.1 Memory Card Menu 6.2.
14 en | Card Reader Remote Control Functions (SanDisk®) 6.2.3 UMS Series Public View System Slide Show Delay Menu The Slide Show Delay menu allows you to adjust the delay time (0-60 seconds) between individual slides. To increase the number of seconds between slides, press the arrow) button and to decrease the number of seconds between slides, press the (right (left arrow) button. When finished, press the MENU/SELECT button to accept changes. Fig. 6.3 6.2.
UMS Series Public View System 6.2.6 Card Reader Remote Control Functions (SanDisk®) | en15 Language Menu The Language menu allows you to switch languages for the card reader OSD. Fig. 6.6 Language Menu 6.2.7 Exit Menu The Exit menu allows you to exit the screen. To resume playing your images, press PLAY/ SLIDE SHOW. Bosch Security Systems, Inc. Installation Manual F01U029703 | 1.0 | 2006.
16 en | Configuring Motion Detection 7 UMS Series Public View System Configuring Motion Detection Passive Infrared Sensor (PIR) detectors are designed to detect movement by sensing the infrared energy emitted from the human body as it moves across the sensor’s coverage sectors (see the shaded areas in the illustration below). The detectors emit no energy of their own. 7.1 Selecting a Mounting Location Mount the monitor where people will most likely cross through the coverage pattern.
UMS Series Public View System 8 Camera Tilt and Pivot Adjustments | en 17 Camera Tilt and Pivot Adjustments You can adjust the camera module position vertically and horizontally, and you can rotate the camera module for proper tilt orientation. See Section 8.1, High-resolution Color Series Camera, on page 17 or Section 8.3, Wide Dynamic Range (WDR) Series Camera, on page 19 for your camera series adjustment points. 8.
18 8.2 en | Camera Tilt and Pivot Adjustments UMS Series Public View System Dip Switch Location for the High-resolution Color Camera The camera module has various settings for any additional adjustments that may be required. See the illustration below and Figure 8.4 on page 19 for the correct camera series settings and dip switch locations. Fig. 8.
UMS Series Public View System 8.3 Camera Tilt and Pivot Adjustments | en 19 Wide Dynamic Range (WDR) Series Camera The figure below illustrates the camera adjustment points for the wide dynamic range camera. Fig. 8.3 Wide Dynamic Range (WDR) Camera Adjustment Points 8.4 Ref. # Description 1 Tilt adjustment; thumb nut 2 Pivot point Dip Switch Location for Wide Dynamic Range (WDR) Camera The figure below shows the location of the dip switches for the WDR camera. ON 1 2 Fig. 8.
20 en | Camera Tilt and Pivot Adjustments 8.5 UMS Series Public View System Focusing the Camera Adjust the focus on the camera by adjusting the rings around the lens until the picture is sharp and clear. If the camera is angled to one side, there is a sliding black mask behind the front window with a hole for the camera. Adjust the camera to the proper tilt position, see Figure 8.1 on page 17 and Figure 8.
UMS Series Public View System 9 Troubleshooting | en 21 Troubleshooting The following are commonly asked troubleshooting questions to better assist you in operating your UMS monitor. 9.1 Make adjustments to the control board and option switches The control board is a microprocessor-based circuit that controls the on-board sensors and a two (2) channel video switcher. The main purpose of the switcher is to display the image from the on-board camera when the PIR detects motion.
22 en | Troubleshooting UMS Series Public View System The following figure illustrates the option switches and their default settings: Fig. 9.
UMS Series Public View System 9.3 Troubleshooting | en 23 No video displayed 1. Check that the power cable is properly inserted and that the power outlet has the proper voltage. Make sure that the power switch located is ON. 2. If power is supplied to the unit: a. Open the cover to the UMS. b. Press the CAM button on the Bosch remote control. c. Check if the Monitor Power LED is illuminated green (see Figure 9.3 on page 24 for location and definitions). 3.
24 9.5 en | Troubleshooting UMS Series Public View System Remote control does not activate the monitor – Make sure that you are pointing the infrared end of the transmitter toward the bottom of the monitor. – Make sure that you are within 9.8–13.1 ft (4–5 m) of the unit. – Make sure that the batteries in the remote control are inserted correctly (see Figure 3.2 on page 5) and are strong enough to power the controller. 9.
UMS Series Public View System 9.7 Troubleshooting | en 25 Memory card images appear stretched and out of proportion The recommended size for images is 640 x 480 pixels (1.33 ratio). If the image was loaded without meeting this specification, the image may look out of proportion. To confirm the true size of your photo, follow these steps: 1. 2. Press either the AUTO or AUX button on the Bosch remote control. Press the PAUSE button and then press the MENU/SELECT button on the SanDisk remote control. 3.
26 en | Troubleshooting 9.12 UMS Series Public View System Monitor does not display AUTO or AUX video when turned on – Ensure that the MEM button on the monitor remote control (Bosch) was used to save the operating mode. – Press the AUTO or AUX button on the monitor remote control (Bosch). If you pressed the On/Off buttons on either remote, the display always returns to the CAM mode. F01U029703 | 1.0 | 2006.07 Installation Manual Bosch Security Systems, Inc.
UMS Series Public View System UMS Ordering Information | en 10 UMS Ordering Information 10.1 Power Supply Part Number Description UMP-24V4P0-60 Power Supply: 27 Single output, 120/24 VAC, 60 Hz, 4 A, with a 6 ft power cord and a steel enclosure 10.2 Mounting Options Part Number Description UMM-LP10B Feed-through Pipe Mount: Includes feed-through ball joint, 10 in. stem and pipe coupling, black UMM-LW10B Feed-through Flange/Wall Mount: Includes feed-through ball joint, 12 in.
28 11 en | Specifications UMS Series Public View System Specifications Electrical Rated Voltage Voltage Range Power at Rated Voltage Sync. Format LCD Panel Screen Size (H x V) Viewable Picture Area Pixel Pitch (H x V) Resolution (H x V) Aspect Ratio Display Colors Response Time Backlight Mechanical Cabinet 24 VAC, 60 Hz 22-26 VAC 80 W/100 VA Mounting NTSC TFT LCD 16.06 x 12.05 in. (408 x 306 mm) 20.1 in. (51 cm) measured diagonally 0.6375 x 0.
UMS Series Public View System Specifications | en 29 Connector Video In RCA (CAM, used by internal camera) UMS-20xxxC-xx RCA (AUX, used by card reader) UMS-20xxxA-xx BNC (video in from external video source) Video Out BNC Power Flying leads Accessories Feed-thru Pipe Mount Feed-thru ball joint , 10-in. UMM-LP10B stem and pipe coupling Monitor Type LCD monitors only Maximum Load 25 lbs (11.34 Kg) Pan Range 0° to 360° Tilt Range 0° to 30° Material Aluminum Finish Black Weight 3.53 lbs (1.
30 en | Specifications F01U029703 | 1.0 | 2006.07 UMS Series Public View System Installation Manual Bosch Security Systems, Inc.
UMS Series Public View Monitor A Accessories mounts 27 power supply 27 replacement parts 27 Adjusting backlight 8 blending 8 brightness 8 camera position 17, 19 color 8 contrast 8 control board 21 dip switch 18 focus 20 horizontal position 8 languages 8 mirroring 9 pivot 17, 19 sharpness 8 tilt 17, 19 tint 8 vertical position 8 AES 18 AUTO mode 7, 12 AUX mode 7, 12 AUX video input 10 B Backlight compensation 18 Backlight option 8 Blending option 8 Bosch remote control 16, 24 Brightness option 8 C CAM
32 en | O On-screen display 6, 7 Option switch 22 Options backlight 8 blending 8 brightness 8 color 8 contrast 8 display aspect 9 factory preset 9 horizontal position 8 information 9 mirroring 9 sharpness 8 tint 8 upside down 9 vertical position 8 OSD menu 8 P Passive Infrared Sensor (PIR) 16 range 16 Phase control 21 Picture Position menu 14 Pivot 17, 19 Power 3 Power connection 4 Power connector 21 Power Save mode 9, 20, 23 Power supply 4, 27 UMP-24V4P0-60 4 R RCA jack 23, 24 Remote control 5 batte
Americas: Bosch Security Systems 130 Perinton Parkway Fairport, New York, 14450 USA Phone +1 800 289 0096 Fax +1 585 223 9180 www.boschsecurity.us © Bosch Security Systems, Inc., 2006 Europe, Middle East, Asia: Bosch Security Systems B.V. Postbus 80002 5600 JB Eindhoven Phone: +31 40 2577 200 Fax: +31 40 2577 202 nl.securitysystems@bosch.com www.boschsecurity.nl www.boschsecurity.com Asia-Pacific: Bosch Security Systems Pte Ltd.