Washer Kit HAC-WAS en Installation Manual
Washer Kit Table of Contents | en 3 Table of Contents 1 Important Safety Instructions 4 2 Description 5 3 Preparing the Product for Use 5 3.1 Contents and Unpacking 5 3.2 Safely Disposing of Packaging Material 5 4 Assembly and Installation 6 4.1 Installing the Pump Tank 6 4.2 Board Wiring 7 4.2.1 Connecting the Power Supply 7 4.2.2 Connecting the UPH Pan/Tilt 8 4.2.3 Installing the Pump (HAC-WAS20-05, HAC-WAS20-50) 8 4.2.4 Installing the Pump (HAC-WAS30-50) 4.
1 en | Important Safety Instructions Washer Kit Important Safety Instructions DANGER! High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation.
Washer Kit 2 Description | en 5 Description A washer kit for the UPH Series High-speed Positioning System. Available in 230 VAC (HACWAS05-50 and HAC-WAS30-50) or 24 VAC (HAC-WAS05-20). The standard pump guarantees a delivery up to a maximum of 5 m (16.4 ft), while the high delivery version (HAC-WAS30-50) delivers up to 30 m (98 ft). It is possible to adjust the articulated nozzle of the pump associating it to a preset in order to obtain the desired position of the wiper and sprinkle functions.
4 en | Assembly and Installation Washer Kit Assembly and Installation DANGER! In the 115/230 VAC powered configuration it is necessary to insert a 1 0 unipolar main switch (open contact distance d>3 mm) upstream on the power line. This switch should be used to disconnect the power supply before carrying out any maintenance operation or before opening the housing. CAUTION! Only qualified personnel should assemble and install the device. 4.
Washer Kit 4.2 Assembly and Installation | en 7 Board Wiring Open the cover of the waterproof box and make the connections. 4.2.1 Connecting the Power Supply DANGER! Always make the base connections with the power supply disconnected and the circuitbreaker open. NOTICE! When commencing installation make sure that the specifications for the power supply for the installation correspond with those required by the device.
en | Assembly and Installation 4.2.2 Washer Kit Connecting the UPH Pan/Tilt To connect the pump of the washer (item 1, below) to the UPH (item 2) refer to the following L N illustration and table. Close the cover door when the connections are complete. Pump board UPH Board (connector CN4) CMD GND 01 C1 Additional Connections for HAC-WAS30-50 4.2.
Washer Kit 4.2.4 Assembly and Installation | en 9 Installing the Pump (HAC-WAS30-50) 1. Adjust the position of the level controller and the weight. 220 (8.66) 120 (4.72) mm (in.) 2. Fill the tank (item 1, below) with water and insert it in the metal cage, taking care to insert the male/female hydraulic coupling (item 2) correctly. 3. Check the delivery hose coupling for the pump (item 3) to make sure a small quantity of water comes out. 4. Bosch Security Systems, Inc. Connect the delivery hose.
4.3 en | Assembly and Installation Washer Kit Installing the Washer to the UPH NOTICE! To attach the base to the support use the new screws provided (item 5, below) and make sure the washers (item 6) are present, as well as the screw seals (item 7) and the gasket (item 8). 1. After attaching the support (item 1, bracket or column support), position the washer pipe support (item 3) in the desired position. Insert the cables inside the support so that they protrude by about 50 cm (19.68 in.). 2.
Washer Kit Assembly and Installation | en 6. 11 Attach the pipe to the washer support using the bracket (item 1), the screws (item 2) and the washers (item 3) supplied. Lock the coupling using the hose clip (item 4) supplied and connect the delivery hose (item 5). 7. To calibrate the jet direct the nozzle towards the glass of the housing. 8. To operate the washer, refer to UPH Series Installation Manual. Bosch Security Systems, Inc. Installation Manual F.01U.206.249 | 2.0 | 2010.
en | Assembly and Installation 4.3.1 Washer Kit Washer Installation Examples Figure 4.1 Example of installation with wall bracket Figure 4.2 Pipe fixed directly to the wall through the plate F.01U.206.249 | 2.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
Washer Kit 4.4 Technical Data | en 13 Fuse Replacement NOTICE! If it is necessary to change the fuse, see the diagram where it is marked FUSE. The size of the fuse will vary according to the voltage of the equipment. HAC-WAS05-20 HAC-WAS30-50 HAC-WAS05-50 5 24 VAC 2AT n/a 120 VAC 0.5AT n/a 230 VAC 250mAT 4AT Technical Data HAC-WAS05-20, HAC-WAS05-50 Dimensions (W x H x L) 301 x 410 x 347.5 mm (11.8 x 16.0 x 13.7 in.
6 en | Dimensional Drawings Washer Kit Dimensional Drawings HAC-WAS05-20, HAC-WAS05-50 269 (10.59) 348 (13.70) 301 (11.85) 200 (7.87) 136 (5.35) 410 (16.14) 152 (5.98) Ø (0. 8 31 ) mm (in.) HAC-WAS30-50 301 (11.85) 200 (7.87) 136 (5.35) 152 (5.98) Ø8 ) (0.31 225 (8.86) 635 (25.0) 410 (16.14) 269 (10.59) mm (in.) F.01U.206.249 | 2.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.
