Technical data

13 Appendix
13.1 List of Standards
Standard Edition Title Concordance
98/37/EG
1998-06-
22
Guideline 98/37/EC of the European Parliament and the
Council dated June 22, 1998, for aligning the legal provisions
and administrative regulations of the member states for ma-
chines
89/336/EEC
1989-05-
03
Guideline of the Council dated May 3, 1989, for aligning the
legal provisions of the member states on electromagnetic
compatibility
DIN EN 50178; VDE
0160
1998-04
Electronic equipment for use in power installations; German
version EN 50178:1997
EN 50178(1997-10)
DIN IEC 60364-4-41;
VDE 0100 part 410
2003-04
Standard draft) DIN IEC 60364-4-41, Edition: 2003-04 Elec-
trical installations of buildings – Part 4-41: Protection for safe-
ty; Protection against electric shock (IEC 64/1272/CDV:2002)
HD 384.4.41 S2(1996-
04); IEC 6036-4-41(1992-
10)
DIN 332-2 1983-05
Center holes 60° with thread for shaft ends for rotating elec-
trical machines
DIN 6885-1 1968-08
Driver connection without pick-up; feather keys, grooves, high
shape
DIN EN 60034-1; VDE
0530 Part 1
2000-09
Rotating electrical machines - Part 1: Rating and performance
(IEC 60034-1:1996, modified + A1:1997 + A2:1999); German
version EN 60034-1:1998 + A1:1998 + A2:1999
EN 60034-1(1998-05); EN
60034-1/A1(1998-05); EN
60034-1/A2(1999-08);
IEC 60034-1(1996-11);
IEC 60034-1 AMD 1
(1997-06); IEC 60034-1
AMD 2(1999-05)
DIN VDE 0298-4; VDE
0298 Part 4
2003-08
Application of cables and cords in power installations - Part 4:
Recommended current-carrying capacity for sheathed and
non-sheathed cables for fixed wirings in buildings and for flex-
ible calbes and cords
DIN EN 60204-1; VDE
0113 Part 1
1998-11
Safety of machinery - Electrical equipment of machines - Part
1: General requirements (IEC 60204-1:1997 + Corrigendum
1998); German version EN 60204-1:1997 (In addition, DIN EN
60204-1 (1993.06) is applicable until 2001.07.01. DIN VDE
60204-1 (1993.06) is applicable until further notice as the ref-
erence standard for EN 60204-3-1 (1990.08), which has been
published in Germany as DIN EN 60204-3-1 (1993.02).
EN 60204-1(1997-12);
IEC 60204-1(1997-10)
DIN 42955 1981-12
Tolerances of shaft extension run-out and of mounting flanges
for rotating electrical machinery, test
IEC 60072(1971)
DIN 748-1 1970-01 Cylindrical Shaft Ends for Electrical Machines IEC 60072(1971)
DIN EN 60034-14;
VDE 0530 Part 14
1997-09
Rotating electrical machines - Part 14: Mechanical vibration of
certain machines with shaft heights 56 mm and higher; meas-
urement, evaluation and limits of vibration (IEC 60034-
14:1996); German version EN 60034-14:1996
EN 60034-14(1996-12);
IEC 60034-14(1996-11)
Project Planning Manual | Rexroth IndraDyn S Electric Drives
and Controls
| Bosch Rexroth AG 189/194
Appendix