Datasheet

706 | Video Transmission Systems | Fiber Optic Video Transmission
Installation/Configuration Notes
The Bosch Fiber Optic Media Converter solution consists
of three core components and several optional
components to help fit every application. To provide fiber
optic communications between a Bosch VG4 AutoDome
and a controller you must use the following:
•
One (1) VG4-SFPSCKT Fiber Optic Ethernet Media
Converter Kit – a printed circuit board installed inside
a VG4 power supply box. (See Technical Specification
Section 1)
•
One (1) CNFE2MC/IN Ethernet Fiber Optic Media
Converter – a rack-mounted or surface mounted head-
end controller. (See Technical Specification Section 2)
•
Two (2) Small Form-factor Pluggable (SFP) modules
– one module is installed in the VG4-SFPSCKT, the
other is installed in the CNFE2MC/IN. (See Technical
Specification Section 3)
Optionally, you can use the following modules to
customize your installation:
•
C1-IN Rack Mount Card Cage (See Technical
Specification Section 4)
•
C1-BP Closure Panel
Technical Specifications
Section 1: VG4-SFPSCKT Fiber Optic Ethernet Media Converter Kit
Description Fiber Optic Ethernet Media Converter kit.
Requires a small form-factor pluggable (SFP)
module (sold separately).
Data Interface Ethernet
Data Rate 10/100 Mbps
IEEE 802.3 Compliant
Full Duplex or Half Duplex Electrical Port
Full Duplex Optical Port
Compatible Receiver CNFE2MC/IN
Installation Installed inside a VG4-A-PA1, VG4-A-PA2,
VG4‑A‑PSU1 or a VG4‑A‑PSU2 power supply box
with supplied mounting hardware
LED Indicators
Power/Link
(on circuit board)
•
Green
Power is applied, fiber link is valid
•
Red
Power is applied, fiber link is missing
•
Green/Flashing
Red, rapid
Power is applied
Fiber link is valid
Data is present and video is streaming from the
VG4 AutoDome to a network connection
•
Green/Flashing
Red, slow
Power is applied
Fiber link is valid
Data is present
Video is not streaming from the VG4 AutoDome,
or the RJ45 connection to the AutoDome is not
valid
RJ-45 Connector
•
Right side,
Flashing Green
Data is present
•
Right side, Off
No data is present
•
Left side, Am-
ber
Link is valid at 100 MB
•
Left side, Off
If the right side is flashing green, link is valid at 10
MB
•
No LED lit
Missing the network cable, defective network ca-
ble or the other end of the network cable is not
connected
Electrical
Power 24 VAC @ 220 mA
(supplied by the VG4 AutoDome)
Current Protection Automatic resettable
Solid-state current limiters
Circuit Board Meets IPC Standard
Mechanical
Dimensions (LxWxH) 7.4 x 7.1 x 3.8 cm (2.9 x 2.8 x 1.5 in.)
Shipping Weight 0.91 kg (2 lb)
Environmental
MTBF > 100,000 hours
Section 2: CNFE2MC/IN Ethernet Fiber Optic Media Converter
Description Fiber Optic Ethernet Media Converter kit. Re-
quires a small form-factor pluggable (SFP)
module (sold separately).
Data Interface Ethernet
Data Rate 10/100 Mbps
IEEE 802.3 Compliant
Full Duplex or Half Duplex Electrical Port
Full Duplex Optical Port
Installation Surface mount or rack mount using C1-IN
rack (sold separately)
Connectors
Power Terminal block
Electrical RJ-45 (10/100 BASE-T/TX)
Socket SFP (10/100 BASE-FX)
LED Indicators
Link/Act
•
Green
Indicates a good fiber connection
•
Flashing Green
Indicates data is present on at least one side
of the IP connection
•
No LED lit
Indicates a loss of fiber connection
Power Green: power is supplied
None: no power supplied
•
Green
Power is supplied
•
No LED lit
No power supplied
RJ-45 Connector
•
Right side, Flashing
Green
Data is present
•
Right side, Off
No data is present
•
Left side, Amber
Link is valid at 100 MB
•
Left side, Off
If the right side is flashing green, link is valid
at 10 MB
Bosch Security Systems B.V. www.boschsecurity.com
13