Fiber Optic Ethernet Media Converter Kit VG4-SFPSCKT en Installation Manual
Fiber Optic Ethernet Media Converter Kit Table of Contents | en 3 Table of contents 1 Important Safety Instructions 4 2 Parts List 5 3 System overview 7 4 Install for an AUTODOME camera 8 5 Install for a MIC analog camera 13 6 Install for an EXTEGRA IP 9000 FX camera 14 7 Troubleshooting 18 Bosch Security Systems Installation Manual 2015.
Fiber Optic Ethernet Media Converter Kit en | Important Safety Instructions 1 Important Safety Instructions Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operation. 1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners. 2. Adjust only those controls specified in the operating instructions. 3. Operate the unit only from the type of power source indicated on the label. 4.
Fiber Optic Ethernet Media Converter Kit 2 Parts List | en 5 Parts List For an AUTODOME camera and for an EXTEGRA camera, the following parts are included in the kit of the fiber optic module: Part Description Part Number Fiber Optic Media Converter Module F.01U.139.350 (with SFP socket) Metal adapter plate F.01U.138.662 Power harness (black) F.01U.026.085 Four (4) Plastic standoff pins F.01U.073.233 Ethernet patch (jumper) cable (blue) F.01U.032.132 with RJ45 connectors One (1) M2.
Fiber Optic Ethernet Media Converter Kit en | Parts List For a MIC camera, the following parts are included in the kit of the fiber optic module: Part Description Part Number Fiber Optic Media Converter Module F.01U.139.350 Fiber cable (gray) F.01U.xxx.xxxx Two (2) Metal standoff pins F.01U.073.233 Ethernet patch cable (blue) with F.01U.032.132 RJ45 connectors 2015.
Fiber Optic Ethernet Media Converter Kit 3 System overview | en 7 System overview This guide provides instructions for installing the Bosch VG4-SFPSCKT Fiber Optic module into a VG4-A-PA1, VG4-A-PA2, VG4-A-PSU1 or a VG4-A-PSU2 AutoDome power supply box, or into one of the following MIC IP power supply units: MIC-IP-PS-115, MIC-IP-PS-24, MIC-IPIRPS-115, MIC-IPIR-PS-230, MIC-IPIR-PS-24.
Fiber Optic Ethernet Media Converter Kit en | Install for an AUTODOME camera 4 Install for an AUTODOME camera Use the following instructions to install the VG4-SFPSCKT Fiber Optic module inside a VG4 Power Supply Box for an AUTODOME camera. 1. Unpack the fiber optic module kit, and remove the parts from the bag. 2. Turn off the power to the VG4 power supply box and remove the cover. 3. Remove the 6-pin connector from the P106 connector inside the power supply box, if present. Figure 4.
Fiber Optic Ethernet Media Converter Kit Install for an AUTODOME camera | en 9 Figure 4.2: Insert standoff pin into power supply board 5. Connect the supplied power harness (black) to the J103 socket on the power supply J103 board, located below the Heater connector. Figure 4.3: J103 socket location 6. Bosch Security Systems Insert three standoff pins into the metal base plate as shown below. Installation Manual 2015.
Fiber Optic Ethernet Media Converter Kit en | Install for an AUTODOME camera Figure 4.4: Placement of standoff pins in base plate 7. Align the upper right hole in the base plate to the standoff pin attached to the power supply box and press the base plate onto the pin. Secure the base plate with the supplied screw in the lower left hole of the P105 connector. Figure 4.5: Attach base place to power supply box 8.
Fiber Optic Ethernet Media Converter Kit Install for an AUTODOME camera | en 11 10. Align the anchor holes on the fiber optic module to the standoff pins on the base plate and press the module onto the standoff pins until secure. Figure 4.6: Attach Fiber Optic board to base plate 11. Attach the supplied power harness (black) to its connector on the fiber optic module. 12. Connect the RJ45 Ethernet patch cable (blue) to its socket on the fiber optic module.
Fiber Optic Ethernet Media Converter Kit en | Install for an AUTODOME camera Figure 4.7: Route cable into power supply box 14. Plug the fiber optic cable (LC or SC connector) into the SFP module inside the power supply unit. 15. Close and secure the power supply box when finished. 16. Restore the power to the power supply box. 2015.
Fiber Optic Ethernet Media Converter Kit 5 Install for a MIC analog camera | en 13 Install for a MIC analog camera Use the following instructions to install the VG4-SFPSCKT Fiber Optic module inside a MIC IP Power Supply to provide fiber optic connections for a MIC550, MIC550IR, or MIC612 camera. 1. Unpack the fiber optic module kit, and remove the parts from the bag. 2. Reverse the fiber board module. 3. Connect the RJ45 cable to the fiber board. 4.
Fiber Optic Ethernet Media Converter Kit en | Install for an EXTEGRA IP 9000 FX camera 6 Install for an EXTEGRA IP 9000 FX camera Use the following instructions to install the VG4-SFPSCKT Fiber Optic module inside an EXTEGRA IP 9000 FX camera. 1. Unpack the fiber optic module kit, and remove the parts from the bag. 2. Remove the three (3) screws that hold the RJ45 coupler assembly in place. Remove the RJ45 coupler assembly. 3.
Fiber Optic Ethernet Media Converter Kit 4. Install for an EXTEGRA IP 9000 FX camera | en 15 Align the screw holes on the fiber optic module to the screw holes from which you removed the screws for the RJ45 coupler assembly. Bosch Security Systems 5. Press the module down until it is secure. 6. Replace the screws. Installation Manual 2015.
Fiber Optic Ethernet Media Converter Kit en | Install for an EXTEGRA IP 9000 FX camera 7. 2015.03 | | Attach the supplied power harness (black) to its connector on the fiber optic module.
Fiber Optic Ethernet Media Converter Kit 8. Bosch Security Systems Install for an EXTEGRA IP 9000 FX camera | en 17 Insert the RJ45 plug. Installation Manual 2015.
Fiber Optic Ethernet Media Converter Kit en | Troubleshooting 7 Troubleshooting Issue Symptom Resolution No data present No Power Check power to VG4-SFPSCKT: – If Green LED is present, then Check power to CNFE2MC: – If Power LED is Green, then check data link Invalid Fiber Link Check fiber connection to VG4-SFPSCKT: – If Red LED is present, then the fiber link is missing.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA, 17601 USA www.boschsecurity.com © Bosch Security Systems, Inc.