AutoDome 100 Series Fixed Camera VG5 100 Series en User Manual
AutoDome 100 Series Fixed Camera Table of Contents | en 3 Table of Contents 1 Camera Setup 4 1.1 Configuring the Camera 4 2 Positioning the Camera 5 3 Adjusting Focal Length (Zoom) and Focus 6 4 Advanced Setup 7 4.1 Accessing and Navigating Menus 7 4.2 Main Menu Function 8 4.2.1 Main Menu 9 4.2.2 ALC Submenu 9 4.2.3 ALC -> SHUTGAIN Submenu 4.2.4 ALC -> SHUTGAIN -> DAY/NIGHT Submenu 10 4.2.5 ENHANCED Submenu 11 4.2.6 COLOR Submenu 11 4.2.
1 en | Camera Setup AutoDome 100 Series Fixed Camera Camera Setup Install and wire the 100 Series AutoDome according to the VG5 AutoDome Installation Manual. A typical system includes a keyboard, matrix switcher, monitor, and appropriate wiring connections. Please refer to the individual product manuals for complete installation and setup instructions for each of the system components. 1.
AutoDome 100 Series Fixed Camera 2 Positioning the Camera | en 5 Positioning the Camera The camera module position can be adjusted along the horizontal, vertical, and diagonal (for azimuth) axes. When adjusting the position, ensure that the picture displayed on the monitor is level. After the covert liner is removed, position the camera by performing the following steps: WARNING! To prevent damage to the camera module do not rotate the camera past its stops. 1.
3 en | Adjusting Focal Length (Zoom) and Focus AutoDome 100 Series Fixed Camera Adjusting Focal Length (Zoom) and Focus To adjust the camera lens focal length and focus, perform the following steps: 1. 2. Select Set Focus Now from the Install menu. To adjust the focal length, loosen the focal (zoom) lock screw and rotate the lens mechanism (WIDE or TELE.) until you achieve the desired field of view. (Item 1, in the figure below). 3.
AutoDome 100 Series Fixed Camera 4 Advanced Setup | en 7 Advanced Setup The VG5-100 Series camera module normally provides an optimal picture without the need for further adjustments. Advanced setup options, however, are available for obtaining the best results from the camera under special circumstances. There are two upper level On-Screen Display (OSD) menus: the Main menu and the Install menu. The Main menu allows you to select and setup the picture enhancement functions.
en | Advanced Setup AutoDome 100 Series Fixed Camera NOTICE! To restore a selected menu item to its factory default, quickly press the Menu Select key twice. To exit the OSD menus from any menu item, hold down the Menu Select key until the OSD disappears. The VG5-100 Series also supports a variety of remote methods to make camera adjustments, including the following: – A Universal keyboard using Bilinx over coax or UTP.
AutoDome 100 Series Fixed Camera 4.2.1 Advanced Setup | en Main Menu Function ALC ENHANCE COLOR BLC Selections Selects Submenu Selects Submenu Selects Submenu ON, OFF, or selects submenu Description Accesses the Auto Level Control menu. Accesses the Picture Enhancement menu. Accesses the Color Control menu. – Enables Back Light Compensation (BLC). – Accesses the BLC submenu. Exits this menu. EXIT 4.2.
en | Advanced Setup AutoDome 100 Series Fixed Camera Function NIGHTSENSE Selections AUTO, OFF, FORCED Description – UTO mode: Camera automatically switches to NIGHTSENSE in low light conditions. – OFF mode: NIGHTSENSE is turned off. – FORCED mode: The camera is set to NIGHTSENSE (black and white) mode. Returns to the ALC menu. EXIT 3. Only available in Day/Night version cameras, color versions show NightSense. NOTICE! If SensUp is active, some noise or spots may appear in the picture.
AutoDome 100 Series Fixed Camera 4.2.5 Advanced Setup | en 11 ENHANCED Submenu Function AUTO BLACK Selections ON, OFF Description ON: Automatically increases the SHARPNESS (-15 to +15) visibility of details. Adjusts the sharpness of the picture. DNR AUTO, OFF Zero (0) is the default position. AUTO: Automatically reduces the noise (Dynamic Noise Reduction) in the picture. This option may cause some motion blur with moving objects. XF-DYN OFF, LOW, MID, HIGH picture contrast.
en | Advanced Setup 4.2.7 AutoDome 100 Series Fixed Camera Back Light Compensation (BLC) Submenu Functions BLC Selections ON, OFF Description ON: The video level optimizes the selected area of the image. Parts outside this area may be underexposed or BLC LEVEL (-15 to +15) overexposed, which is normal. Adjusts the balance between the selected BLC area and its BLC AREA Selects submenu surroundings. Accesses the Back Light Compensation area menu.
AutoDome 100 Series Fixed Camera 4.3.1 Advanced Setup | en 13 Install Menu Function Selections CAMERA ID Selects submenu SET FOCUS NOW Description Accesses the Camera ID submenu. Completely opens the lens iris for best focus. The recommended focus procedure is: – Unlock the focus locking screw. – From the INSTALL menu highlight SET FOCUS – Turn the lens focus adjustment as required – Tighten the lens focus locking screw. NOW.
en | Troubleshooting Guide AutoDome 100 Series Fixed Camera 5 Troubleshooting Guide 5.1 VG5 AutoDome Operation and Control Problem Solution No video – Check that the Green LED on the AutoDome CPU board is on. This LED indicates video from the camera. If the Green LED is off, then: – Check that the Red LED on the AutoDome CPU board is slowly blinking. This LED indicates power to the AutoDome power supply board and to the CPU Module.
AutoDome 100 Series Fixed Camera Local Keys Disabled – Troubleshooting Guide | en 15 This message appears if the Camera Menu Keyboard has been disabled through the CTFID tool. Select OnLine Config>Installer Options>Miscellaneous>Camera Buttons>Disable No Remote Menu – Ensure that all coax, fiber and Ethernet cables are properly connected. See the VG5 AutoDome Installation Manual. Access If O.K., then: – Check if you can access the AutoDome OSD menus. If O.K.
en | Troubleshooting Guide AutoDome 100 Series Fixed Camera Inside of – EnviroDome bubble If status reports Heater No Power, then: Check the status of the Heater Module (ON-66-ENTER). is foggy – Turn off the power to the AutoDome. – Check the FX103 fuse in the Power Supply Box for power (24 V) to the heater module. If O.K., then: – Check all wiring and connector pins to the heater module.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.
