VideoEdge Camera Handler Release Notes VideoEdge 4.2.1 Camera Handler v4.2.1.1022 In case of discrepancy, the information in this document supersedes information in other document(s), media(s) or provided verbally.
Notice The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Copyright Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of Tyco Security Products. © 2013 Tyco Security Products. All Rights Reserved.
General Purpose The purpose of this document is to provide a detailed list of supported manufacturers and manufacturers’ camera lines integrated and supported by the American Dynamics VideoEdge Network Video Recorder version 4.2.1 and the VideoEdge Camera Handler version 4.2.1. Cameras and Encoders supported and available with current version 4.2.
General Purpose 1-2 Camera Handler Release Notes
What’s New in This Release This camera handler release provides integration for the following cameras: • illustra 600/610 Box and Bullet In addition, the handler improves bandwidth efficiency for American Dynamics IP SpeedDome cameras with firmware 2.0 or later Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification illustra 600/610 Bullet Cameras ADCi600-B021 H.264, MJPEG Yes 1/1 4.2.1 Tested & Certified ADCi600-B041 H.264, MJPEG Yes 1/1 4.2.
What’s New in This Release Camera Firmware Approx Bitrate at Quality Setting (Max FPS, Max Resolution) 20 40 60 80 100 PAL v1.x firmware 1,140,000 5,240,000 9,220,000 16,780,000 25,160,000 NTSC v1.x firmware 1,180,000 5,320,000 8,160,000 15,100,000 24,750,000 PAL v2.x firmware 278,600 557,000 1,080,000 2,130,000 4,220,000 NTSC v2.x firmware 290,000 550,000 1,070,000 2,120,000 4,200,000 Note Since the NVR uses CBR to control bitrate, the bandwidth of H.
Continual Support At any given time there is only one camera pack available for the VideoEdge NVR. This camera pack provides full support to all existing (updates and add-ons) and new cameras available for the VideoEdge NVR.
Continual Support 3-2 Camera Handler Release Notes
American Dynamics Supported American Dynamics cameras: Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification Video Encoders ADEIP8H H.264, MJPEG Yes 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADEIP8M MJPEG, MPEG4 Yes 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADCIPEBPN MJPEG, MPEG4 Yes 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADCIPEBPPE MJPEG, MPEG4 Yes 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADCIPEBPPU MJPEG, MPEG4 Yes 4.0, 4.0.1, 4.
American Dynamics Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification ADVEIPSD22P H.264, MJPEG, MPEG4 Yes 4/4 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADVEIPSD35N H.264, MJPEG, MPEG4 Yes 4/4 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADVEIPSD35P H.264, MJPEG, MPEG4 Yes 4/4 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified illustra 210 Mini Dome Cameras ADCi210-D111 H.264, MJPEG Yes 1/1 4.1, 4.2, 4.2.1 Tested & Certified ADCi210-D011 H.
American Dynamics Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification ADCi600-D033 H.264, MJPEG Yes 1/1 4.1, 4.2, 4.2.1 Tested & Certified ADCi600-D143 H.264, MJPEG Yes 1/1 4.1, 4.2, 4.2.1 Tested & Certified ADCi600-D043 H.264, MJPEG Yes 1/1 4.1, 4.2, 4.2.1 Tested & Certified ADCi600-D343 H.264, MJPEG Yes 1/1 4.1, 4.2, 4.2.1 Tested & Certified illustra 610 Mini Dome Cameras ADCi610-D111 H.264, MJPEG Yes 1/1 4.1, 4.2, 4.2.
American Dynamics Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification ADCi400-D013 H.264, MJPEG Yes 1/1 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADCi400-D031 H.264, MJPEG Yes 1/1 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADCi400-D033 H.264, MJPEG Yes 1/1 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified illustra 400 WDR Outdoor Mini Dome Cameras ADCi400-D021 H.264, MJPEG Yes 1/1 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Tested & Certified ADCi400-D023 H.
ACTi Corporation This version of the VideoEdge camera handler is fully integrated with ACTi Corporation line of IP cameras. ACTi has number of API’s (Application Programming Interface) camera handlers to communicate with their cameras. This version of the VideoEdge NVR is fully integrated with the ACM models (cameras using firmware version v3.13.16-AC) and TCM models (cameras using firmware version v4.11.09-AC).
ACTi Corporation Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification TCM5311 4.1, 4.2, 4.2.1 Works as designed TCM5611 4.1, 4.2, 4.2.
Arecont Vision VideoEdge camera handler is fully integrated with the Arecont Vision line of megapixel cameras including full support for the 180˚ and 360˚ lines of panoramic view cameras. Arecont Vision cameras operating system (firmware) is continually evolving; please make sure your camera is running the most current firmware available from Arecont Vision (available from http://www.arecontvision.
Arecont Vision Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification AV2100 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV2100DN 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV2100IR 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV2105 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV2105DN 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV2105AI 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV2110 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV2110DN 4.0.1, 4.
Arecont Vision Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification AV5100AI 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV5105 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV5105DN 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV5105AI 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV5110 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV5110DN 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV5115 4.0.1, 4.1, 4.2, 4.2.1 Works as designed AV5115DN 4.0.1, 4.1, 4.2, 4.2.
Arecont Vision 6-4 Camera Handler Release Notes
AXIS Communications VideoEdge camera handler is fully integrated with the AXIS communications line of IP cameras and video encoders. AXIS has number of API’s (Application Programming Interface) camera handlers to communicate with their cameras. The VideoEdge NVR is fully integrated with the VAPIX® API Version 2 (cameras using firmware version 4.xx) and VAPIX® API Version 3 (cameras using firmware version 5.xx).
AXIS Communications Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification (Minimum Camera Pack Version) M1103 4.0.1, 4.1, 4.2, 4.2.1 Works as designed M1104 4.0.1, 4.1, 4.2, 4.2.1 Works as designed M1113 4.0.1, 4.1, 4.2, 4.2.1 Works as designed M1114 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P1311 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P1343 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P1343-E 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P1344 4.0, 4.
AXIS Communications Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification (Minimum Camera Pack Version) M3203-V 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P3301 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P3301-V 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P3304 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P3304-V 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P3343 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed P3343-V 4.0, 4.0.1, 4.1, 4.2, 4.2.
AXIS Communications Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification (Minimum Camera Pack Version) P5534-E 4.0.1, 4.1, 4.2, 4.2.1 Works as designed Q6032-E 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed Q6034 4.0.1, 4.1, 4.2, 4.2.1 Works as designed Q6034-E 4.0.1, 4.1, 4.2, 4.2.1 Works as designed 231D+ 4.0.1, 4.1, 4.2, 4.2.1 Works as designed 232D+ 4.0.1, 4.1, 4.2, 4.2.1 Works as designed 233D 4.0, 4.0.1, 4.1, 4.2, 4.2.1 Works as designed M5013 4.1, 4.
Bosch Supported Bosch cameras: Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification AutoDome (Supported Firmware v15500552) VJR-821-ICCV 4.2.1 Works as designed VJR-811-ICCV 4.2.1 Works as designed VJR-821-IWCV 4.2.1 Works as designed VJR-811-IWCV 4.2.1 Works as designed VJR-821-ICTV 4.2.1 Works as designed VJR-811-ICTV 4.2.1 Works as designed VJR-821-IWTV 4.2.1 Works as designed VJR-811-IWTV 4.2.1 Works as designed VG5-825-ECEV 4.2.
Bosch 8-2 Camera Handler Release Notes
CBC Supported CBC Cameras: Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification Fixed IP Cameras MP1A 4.0.1, 4.1, 4.2, 4.2.1 Works as designed MP1DN 4.0.1, 4.1, 4.2, 4.2.1 Works as designed MP2A 4.0.1, 4.1, 4.2, 4.2.1 Works as designed MP2DN 4.0.1, 4.1, 4.2, 4.2.1 Works as designed MP3DN 4.0.1, 4.1, 4.2, 4.2.1 Works as designed MP5A 4.0.1, 4.1, 4.2, 4.2.1 Works as designed MP5DN 4.0.1, 4.1, 4.2, 4.2.1 Works as designed 4.0.1, 4.1, 4.2, 4.2.
CBC 9-2 Camera Handler Release Notes
FLIR In this release the VideoEdge camera pack is fully integrated with FLIR’s D, PT and F series, multi sensor, pan tilt and fixed thermal security cameras. The following cameras are supported with minimum camera firmware version nexus-serverGD_v2.5.9.17. Supported FLIR cameras: Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification Fixed Cameras F-112 4.1, 4.2, 4.2.1 Works as designed F-117 4.1, 4.2, 4.2.1 Works as designed F-124 4.1, 4.2, 4.2.
FLIR Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification D-625 4.1, 4.2, 4.2.1 Works as designed D-645 4.1, 4.2, 4.2.1 Works as designed PT-112 4.1, 4.2, 4.2.1 Works as designed PT-117 4.1, 4.2, 4.2.1 Works as designed PT-124 4.1, 4.2, 4.2.1 Works as designed PT-304 4.1, 4.2, 4.2.1 Works as designed PT-307 4.1, 4.2, 4.2.1 Works as designed PT-313 4.1, 4.2, 4.2.1 Works as designed PT-324 4.1, 4.2, 4.2.1 Works as designed PT-334 4.1, 4.2, 4.2.
Panasonic Corp VideoEdge camera handler is fully integrated with the Panasonic line of IP cameras. Panasonic, generally, doesn't change the core API interface for their cameras. VideoEdge camera handler is based on Panasonic core API package version 1.28, supporting both WV and DG versions of the listed cameras. As Panasonic continue to release new cameras there may be instances where specific Panasonic cameras are not listed in the available camera pack.
Panasonic Corp Model SC395 CODEC Supported Audio I/O VideoEdge Versions Supported Certification 4.0.1, 4.1, 4.2, 4.2.1 Works as designed NP244 4.0.1, 4.1, 4.2, 4.2.1 Works as designed NP304 4.0.1, 4.1, 4.2, 4.2.1 Works as designed NP502 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SP102 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SP105 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SP302 4.1, 4.2, 4.2.1 Works as designed SP305 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SP306 4.0.1, 4.1, 4.
Samsung Supported Samsung Cameras: Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification Encoders SPE-100 4.2.1 Works as designed SPE-400 4.2.1 Works as designed SNZ-5200 4.2.1 Works as designed SNB-2000 4.2.1 Works as designed SNB-3000 4.2.1 Works as designed SNB-3002 4.2.1 Works as designed SNB-5000 4.2.1 Works as designed SNB-7000 4.2.1 Works as designed 4.2.1 Works as designed SNV-5010 4.2.1 Works as designed SNV-3080 4.2.
Samsung Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification SND-7080 4.2.1 Works as designed SND-7080F 4.2.1 Works as designed SNP-3120 4.2.1 Works as designed SNP-3120V 4.2.1 Works as designed SNP-3120VH 4.2.1 Works as designed SNP-3371 4.2.1 Works as designed SNP-3302 4.2.1 Works as designed SNP-3302H 4.2.1 Works as designed SNP-3371TH 4.2.1 Works as designed SNP-5200 4.2.1 Works as designed SNP-5200H 4.2.1 Works as designed SNP-3430H 4.2.
SONY This version of VideoEdge camera handler provides full integration with the SONY line of Video Encoders and IP cameras. SONY has number of API’s (Application Programming Interface) camera handlers to communicate with their cameras. The VideoEdge NVR is fully integrated with SONY’s 3rd, 4th, and 5th generations of IP cameras. As SONY continues to release new cameras there can be instances where specific SONY cameras are not listed in the camera pack cameralist.
SONY Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification Mini Dome Cameras SNC-DH140 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-DH140T 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-DH240 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-DH240T 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-DH280 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-DH120 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-DH120T 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-DH220T 4.0.1, 4.1, 4.
SONY Model CODEC Supported Audio I/O VideoEdge Versions Supported Certification SNC-RX550P 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-RX570N 4.0.1, 4.1, 4.2, 4.2.1 Works as designed SNC-RX570P 4.0.1, 4.1, 4.2, 4.2.
SONY 13-4 Camera Handler Release Notes
Camera Specific Release Notes This section is a collection of camera release notes as provided with each camera release. This section provides detailed description for each manufacturer cameras, performance limitations and supported features.
Camera Specific Release Notes 14-2 Camera Handler Release Notes
American Dynamics 8 Channel IP Encoder (M&H) Supported Key Functions • Video Streaming – Single and Dual • Video Codec – MJPEG, MPEG4 and H.264 and MPEG4 MJPEG • Audio Streaming – Audio Codec are AAC, G.711 ulaw and G.
American Dynamics 8 Channel IP Encoder (M&H) • Changing streaming parameters like bit-rate, quality, frame-rate, key frame interval and others would require the stream to be restarted, hence a small glitch in play out might be observed during this time. • Focus and Iris is not supported by thin Client Web GUI, because 8 Channel Encoder supports only relative value change and does not support absolute change of values. However it is supported in Pattern.
American Dynamics Fixed IP Camera Supported Firmware • v1.57 or later Supported Key Functions • Video Streaming: Single • Video Codec: MJPEG and MPEG-4 • Audio Streaming: Model specific, G.
American Dynamics Fixed IP Camera Limitations • The camera will reboot when changing codec (audio or video), resolution, frame rate,key frame interval, video quality, audio volume, enable audio / audio in and any other audio / video properties. Reboots will take about 20 to 30 seconds and 1 minute to be back online. • Single HTTP stream to send audio/video interleaved MPEG4 video. • When camera is rebooted or codec is changed, adjusts focus under grey and will take 30 seconds to go to color.
American Dynamics Fixed Camera (illustra 400 series) Supported Firmware • v2.20 or later Supported Key Functions • Video Streaming – Single, Dual • Video codec – H.264 and MJPEG • Audio Streaming – G.711 ulaw and G.726, single stream only • Dry Contact Events – Single.
American Dynamics Fixed Camera (illustra 400 series) Limitations • The camera will reboot when changing codec (audio or video), resolution, frame rate, key frame interval, video quality, audio volume, enable audio / audioin and any other audio / video properties. The reboots will take about 20 to 30 seconds. • All audio and video streams will be lost when the camera reboots. All audio and video streams will then need to be re-established.
American Dynamics Fixed Camera (illustra 210, illustra 600 and illustra 610 Domes) Supported Key Functions • Video Streaming • Audio Streaming – Supports G711mulaw stream (600/610/210). illustra 610LT does not support audio. • Dry Contact Events – Single camera is pulled for Dry Contact at 100ms interval (600/610/210). illustra 610LT does not support dry contact events.
American Dynamics Fixed Camera (illustra 210, illustra 600 and illustra 610 Domes) rtsp://camera_ip:7781/secondarystream (handler uses this). • The rtsp A/V mixed stream URL is rtsp://camera_ip:7778/primarystream rtsp://camera_ip:7780/secondarystream. • The end user can modify the port numbers via camera webpage.
American Dynamics Fixed Camera (illustra 210, illustra 600 and illustra 610 Domes) • NVR only supports audio in 8KHz. • illustra 600, add 720p and 1080p resolution for MJPEG stream, change the codec or resolution of stream 1 will report an error. illustra 600 camera only supports one 720P/1080P stream. If there is one 720P/1080P stream on the NVR, it is impossible to set another. Please refer to the camera limitation.
American Dynamics Fixed Camera (illustra 210, illustra 600 and illustra 610 Domes) •illustra 210 = H264, Maximum available Fps, D1 •illustra 600 = H264, Maximum available Fps , 1280X720 •illustra 610 = H264, Maximum available Fps , 1920X1080 Special Points • Some properties are normalized to a percentage (1-100), but the real value in camera is a range from -127 to 128. This results in the values in the NVR not covering all values in the camera.
American Dynamics Fixed Camera (illustra 600, 610 and 600LT Series Box and Bullets) Supported Firmware • v1.0.16 or later Supported Key Functions • Video Streaming (MJPEG, H.
American Dynamics Fixed Camera (illustra 600, 610 and 600LT Series Box and Bullets) rtsp://camera_ip/video2.sdp • The rtsp A/V mixed stream URL is: rtsp://camera_ip/live1.sdp or rtsp://camera_ip/live2.sdp Required Network Ports • Port 80 is for HTTP • Port 554 is for RTP/RTSP Default Username & Password • Username: admin • Password: admin Limitations • When a factory defaulted camera is added to an NVR, the default settings are: H.264, 7 FPS, CIF.
American Dynamics Fixed Camera (illustra 600, 610 and 600LT Series Box and Bullets) steams configuration on the camera. The camera only identifies the streams by the stream codec (ignoring FPS and resolution). In some instances when NVR streams are both configured with the same codec, changing one of the streams will not necessarily change the parameters on the specified stream. • It is recommended to configure the camera to the cameras FPS limitations.
American Dynamics Fixed Camera (illustra 600, 610 and 600LT Series Box and Bullets) • It may take 2 minutes when changing other FPS to 3 FPS. The reason for this is a mismatched GOP and frame rate will cause a longer re-connection time due to waiting for another frame. GOP size is much larger than Frame Rate, it may take a longer time for video to restart. • Some properties are normalized to a percentage (1-100), but the real value in camera is a range from 0 to 255.
American Dynamics IP SpeedDome Serial Number NVR will use the camera’s MAC address as the camera serial number. Supported Key Functions • Video Streaming 4 max • Video Codec – • MJPEG, MPEG4 and H.264 • Audio Streaming – Audio codecs are AAC, G.711 ulaw and G.711 alaw. No PCM audio stream • Mechanical Pan and Tilt and Optical Zoom • Dry Contact Events – Up to 4 dry contact events are support. The camera is polled for dry contact event at 30s interval.
American Dynamics IP SpeedDome Default Username & Password • User name: admin • Password:admin Bandwidth Efficiency Bandwidth efficiency has been improved for American Dynamics IP SpeedDome cameras running firmware version 2.0 or later. The VideoEdge NVR will use an algorithm to control video quality according to the camera firmware version. If version is less than 2.0, the video quality will be altered by changing cameras quality value. If version is 2.
American Dynamics IP SpeedDome • The maximum frame rate in dual streaming mode is: • When codec is H.264/MJPEG: •The maximum frame rate for the H.
American Dynamics IP SpeedDome 20-4 Camera Handler Release Notes
ACTi Corporation Supported Key Functions • Video Streaming • Query Device • Dry Contact Events • Reboot Unsupported Key Functions • Audio Streaming • PTZ • Power Off • Get Log • Restore Factory Defaults • Find Device Minimum Firmware • For ACM models – v3.13.16-AC • For TCM models – v4.11.
ACTi Corporation Default Username & Password • Username: admin • Password: 123456 Supported Resolution All resolutions less than or equal to 1280x720 are dynamically acquired by the camera. Limitations • Resolutions larger than 720p are unsupported due to an incompatible algorithm used by the camera when the stream's resolution is larger than 720p.
ACTi Corporation • The ACTi generic camera driver will not support the following features: • Image settings: •Lens day/night mode •Brightness •Contrast •Sharpness • H.264 stream • Resolutions larger than 720p are unsupported. Should a camera support a higher resolution, this will not be available via NVR. Known Issues • The TCM3511 has an issue with Reverse playback in the VEClient. The user will experience a stutter with the H.264 stream due to the first key frame being received every second.
ACTi Corporation Resolution: Power Cycle first. If problem persists, carry out hardware reset. • Sometimes the camera’s web GUI will report “Error: Streaming Engine is not running”, when the issue happens there is no stream given out. The camera can be restored after a manual reboot. Resolution: Hardware reset • Sometimes modifying contrast or saturation will cause the camera to crash, when this happens, the user may receive the following message on the camera’s web GUI: “Please contact your provider.
Arecont Vision Supported Key Functions • The Arecont Vision AV8xxx employs four, two-megapixel cameras in 180˚ or • 360˚ panoramic views. Models are available in a variety of options including H.264 • or MJPEG video formats, Day/Night, Heater/Blower, recessed or IP66 housings. • Using the American Dynamics victor unified client, operators can view • each image independently or combination of them in a multi camera view in victor. • Video Streaming – Single and Dual • Video Codec – MJPEG and H.
Arecont Vision Limitations • The AV8xxx will be viewed with Victor Client. Not all functionality is supported by the Web-Client • VideoEdge Version 4.0 had a limitation for motion detection data generation of M-JPEG stream with video resolution greater than 4CIF/D1. VideoEdge version 4.1 increases the resolution to 1280x960 supporting second stream from a megapixel camera. • VideoEdge 4.2 (as with VideoEdge 4.0 and 4.
Arecont Vision • When upgrading the camera handler pack, note that the parameters of video streams may be changed to the default values. It is recommended to recheck video codec parameters when upgrading or restoring configuration backups. • For AV8XXX cameras, motion detection can only be enabled if single MJPEG is set for every lens.
Arecont Vision will trigger a lost video alert. Cameras where this issue has been observed are AV3115DN, AV5125IR, AV8185DN. Considerations • Arecont only support two resolutions, one is half, the other is full, and we will convert it to width x height according to the actual picture size. • MJPEG over RTSP is not supported. • Video Codec Properties are all set to DB. The properties on camera’s web page are not used, and these settings are for default stream fetching by web.
Arecont Vision AV1310 AV1315 AV1325 AV1355 AV2100 AV2105 AV2110 AV2115 AV2125 AV2155 AV2805 AV2815 AV2825 AV3100 AV3105 1280 x 1024 1280 x 1024 1280x1024 1280 x 1024 1600 x 1200 1600 x 1200 1600 x 1200 1920 x 1080 1920 x 1080 1600 x 1200 1920 x 1080 1920 x 1080 1920x1080 2048 x 1536 2048 x 1536 AV3110 AV3115 2048 x 1536 2048 x 1536 AV3125 2048 x 1536 AV3155 2048 x 1536 AV5100 AV5105 2560x1920 2560 x 1920 AV5110 AV5115 2560 x 1920 2560 x 1920 AV5125 2560 x 1920 AV5155 2560 x 1920 1280 x 1024
Arecont Vision 22-6 Camera Handler Release Notes
Axis Communications Supported Key Functions • Video Streaming – Single and Dual • Video Codec – MJPEG, MPEG4 and H.264 • Audio Streaming • Audio codec supported depends on camera functionality • Dry contact events Required Network Ports • Port 80 is for HTTP • Port 554 is for RTSP Default Username & Password • Username: root • Password: pass Note These are associated with password group 0 (default) Supported Camera API and Models • Camera API: VAPIX 2 and VAPIX 3.
Axis Communications Camera Serial Number NVR will use the camera’s MAC address as the camera serial number. Supported Key Functions • Video Streaming – Single and Dual • Audio Streaming – Audio codec supported depends on the camera. • PTZ – Applies to cameras that have mechanical Pan and Tilt and Optical Zoom. • Dry Contact Events • Query Device • Reboot Device Video/Audio Stream Feature • For VAPIX 3 cameras, all MJPEG, MPEG-4 and H.264 streams can have different frame rates, resolution and quality.
Axis Communications • Q1755 without PT head installed will still show up as a PTZ camera in NVR. However, none of the PTZ functions will work. This limitation could apply to all cameras that has built-in PT/PTZ head support. • Older versions of the AXIS handler may have set the “exposure”, “input gain”, “wdr” and other parameters on some AXIS cameras to invalid values. • The camera’s web interface can be used to determine whether the camera parameters have been set to invalid values.
Axis Communications recorded playback by Victor Client, a blank image appears for a very short period at the point in time where the audio codec was changed. • If the customer needs to change the active state of a dry contact input then it should be changed before adding a corresponding alarm sensor otherwise an alarm/alert may be caused as a result of changing the active state. • For H.264 video streams, the NVR web client does not allow the H.264 video quality and H.
Axis Communications • The Sequence portion of the NVR web client PTZ page may appear or disappear when the page is refreshed. • If the MJPEG quality level is set to 100 at high resolutions ( 1920x1200 for example ) then live viewing problems ( high latency, momentary loss of video, etc) may be observed in a Victor Client surveillance screen if that workstation is also trying to live view using the NVR web client.
Axis Communications 23-6 Camera Handler Release Notes
Bosch Supported Key Functions • Video Stream • Query Device • Audio Stream • Events • PTZ Video Stream Supports MJPEG and H264 streams NVR supports dual H264, or one H264 and one MJPEG Audio Stream Supports audio codec G.
Bosch Default Ports • Port 80 for HTTP • Port 554 for RTSP Default Username & Password Service user and default password is blank.
Bosch Supported Resolutions Model Max Resolution (Default Value) Resolution List in NVR 4.
Bosch Limitations • Due to a camera limitation, the handler can only support one MJPEG stream. If a second MJPEG stream is enabled, the NVR will produce an error message. • Bosch camera supports two H264 streams. Handler default stream is H264 stream1. Due to camera limitations, H264 stream 2 resolution depends on H264 stream1 resolution. Note H264 stream 1 and stream 2 refer to H264 streams from the camera corresponding with the camera encoder profile1 and profile 2, not streams 1 and 2 on the NVR.
Bosch • When setting up Dry Contacts on NBN-921-P IVA serials and NBN-498 serials, it is necessary to activate the Alarm Inputs on the camera GUI first. Users must change the Active dropdown list value from 'None' to 'N.O.' or 'N.C.' on the camera, as 'None' means disabled and this does not automatically change when Dry Contacts are activated on the NVR.
Bosch resolution value on Stream 2. • Due to the NVR web client known issue, when setting the resolution for the second H264 stream, set it on the advance edit page. This is due to the fact it is a copy setting of H264 stream 1 on camera list page with editing status, and real available resolution may not be included in the copy of the resolution list.
CBC Supported Key Functions • Video Streaming – Single and Dual • MJPEG and H.264 video codecs • Query Device Unsupported Key Functions • PTZ Operation • Audio Streaming • Dry Contact Events • Power off devices • Get device log • Find Devices • Reboot • Reset to factory default Camera Serial Number NVR will use the cameras MAC address as the camera serial number.
CBC Default Username & Password • Username: admin • Password: Supported Resolution Model Max Resolution Resolution Options on NVR MP1A MP1DN MP2A MP2DN MP3DN MP5A MP5DN MP8D-L4 1280x1024 1280x1024 1600x1200 1600x1200 2048x1536 2560x1920 2560x1920 1600x1200 1280x1024 / 640x512 1280x1024 / 640x512 1600x1200 / 800x600 1600x1200 / 800x600 2048x1536 / 1024x768 (For MJPEG – only 1024x768) 2560x1920 / 1280x960 2560x1920 / 1280x960 (For MJPEG – only 1280x960) 1600x1200 / 8
CBC Considerations CBC model cameras with firmware version 62414 will be configured as their Arecont equivalent, also taking the Arecont model. In firmware 64238 CBC model cameras will be identified as a CBC model, but for codec parameters. CBC model cameras still correspond with Arecont model cameras.
CBC 25-4 Camera Handler Release Notes
FLIR Supported Key Functions • Video Streaming – Single and Dual • PTZ – Applies to cameras that have mechanical Pan and Tilt and Optical Zoom. • Query Device • Reboot Device Unsupported Key Functions • Find devices • Power-off device • Get device log • Reset to factory default • Digital PTZ – Applies to cameras that support digital PTZ. • Audio Streaming Camera Serial Number NVR will get the serial number from each camera.
FLIR Default Username & Password • Username:admin • Password:indigo Firmware Requirements Nexus Server F, D & PT-Series’ F, D & PT-Series’ Nexus server must be updated to v2.5.9.17 or later. Note: v2.5.9.17 is in beta FLIR Camera Firmware must be v2.5.9.15 or later. Video Stream Feature Specific video stream feature characteristics are: PT-Series, F-Series & D-Series: MJPEG, MPEG4 and H.264. Support dual video streams.
FLIR Limitations 1 2 3 Model Known Camera Limitations F-Series D-Series PT-Series F-Series D-Series PT-Series F-Series D-Series PT-Series Due to a necessity of FLIR camera video hardware re-start, it may take about 48 seconds for the video stream to come back after any stream property changes. Camera may take more than 5s to respond to a CGI command, this may cause NVR to timeout. This is camera performance issue.
FLIR D-Series D-Series camera returns incorrect firmware version number in the IRDeviceVersionGet CGI response. Camera firmware version number is only available on the main page of the camera’s web configuration tool. The camera firmware version number displayed on NVR is incorrect. Video image streamed from a F-Series camera always has a big border when being displayed on NVR and Victor Client. Video image of moving objects looks interlaced on Quick Time and Java Applet Web Browser.
FLIR 3 Models: PT-Series/D-Series/F-Series Steps for enabling the Second stream on the PT-Series/D-Series Before setting a FLIR camera’s IP address on NVR, the user must enable the second stream for each camera LEN on the PT-Series/D-Series/FSeries.
FLIR 5 The following describes the steps for installing a dictionary file to a FLIR camera. Note: In order for a FLIR camera to properly respond to all the CGIs, the camera must be installed with the correct dictionary file version specified in this release note. 1 Open Internet Explorer. Go to http:// 2 Select "Server Status" 3 In the "Nexus dictionary file" Window 4 a Select "Browse" b Enter the path of the folder which contains the correct Nexus dictionary file to be uploaded.
FLIR Troubleshooting Error Message on NVR Possible root causes NVR Failed to add camera. -NVR Lost communication Ping camera IP to make sure camera is connected network. with Camera Open a web browser. Issue “ServerWhoAmI” CGI command, “ - Camera is offline SERVERWhoAmI” If camera responds the above CGI with no error, this means - Camera server is not communication between NVR and Camera communication running through port 8080 has been established.
FLIR 26-8 Camera Handler Release Notes
Panasonic Supported Key Functions • Video Streaming – Single and Dual • Video Codec – MJPEG, MPEG4 and H.
Panasonic Supported Camera API & Models Model Minimum Camera Firmware Version NW484 NW502S, NP502 1.61E0 1.10 NW960, NW964, NS950, NS954 SF332, SF335, SF336 SF342, SF346 SW352 SW355 NP244, NF284 NS202, NS202A SC384 SC385, SW395 SP102 SP105 1.61E0 1.03 1.34 1.06 1.04 1.60 2.70 1.05 1.01 1.01 1.01 SP302, SP305, SP306 NP304, NF302 NP244 Generic Fixed – for all unlisted Panasonic IP Fixed Cameras, not PTZ 1.04 1.61E0 1.
Panasonic The specific Audio Video stream feature characteristics by model families are: Model Audio/Video Stream Feature NW484, NW960, NW964, NS950, NS954, NP304, NF302, NS202, NS202A, NP244, NF284 NW502S, NP502, SF332, SF335, SF336, SP302, SP305, SP306, SC384, SC385, SW395, (SF342, SF346 SW352, SW355)Generic Fixed SP102, SP105 MJPEG and MPEG4 Support only 1 video stream in order to achieve high frame rate MJPEG, MPEG4 and H.
Panasonic • Due to camera performance limitations when using dual stream out of a M-JPEG/MPEG4/H.264 camera, the camera might not deliver the requested frame rate. Please refer to Panasonic product catalog for more details • Fractional frame rate support is not supported with the VideoEdge NVR and will be reported as “unknown” • NW502S and NP502 max frame rate for dual stream is 15FPS at VGA and 10FPS at QVGA • SF332, SF335, SF336, SP102, SP105, SP302, SP304, SP305 and SP306 are 1.
Panasonic Settings, Video Processing Amp) is not available. Some camera models, including SC384, will display Back Light Compensation as “Unknown” and other models will display “0”. Note Please refer to Panasonic cameras release notes published on the Panasonic website for more information about Panasonic cameras and limitations.
Panasonic NP304, NF302 NS202, NS202A NP244, NF284 SC385, SW395 (SC384) NP244, NF284, NS202A, NW484, NS954, NW964, NF302, NP304 27-6 Picture quality is 1.3 mega pixels; there are two aspect ratios 4:3 & 16:9. MPEG-4 is not available when 16:9 is selected When MPEG-4 transmission is set to On, the maximum frame rate for MJPEG is 5fp The maximum MPEG4 resolution is 1280x960. The maximum MJPEG resolution is 640x480 When MPEG-4 transmission is set to On, the maximum frame rate for MJPEG is 5fp.
Panasonic Generic SP302, SP305, SP306 , (SF342, SF346) SP102, SP105 Does not support any other settings other than video, audio and event stream related functions The mode settings of H.264 and MPEG-4 operation need to be explicitly set at the camera.
Panasonic 27-8 Camera Handler Release Notes
Samsung Supported Key Functions • Video Stream • Audio Stream • PTZ • Query Device • Dry Contact Events Video Stream Supports MPEG4, MJPEG and H264 streams (Only viable dual streaming is a combination of MPEG4 + MJPEG, H264 + MJPEG, or H264 + MPEG4 refer to Limitations for further details) Audio Stream Supports G711mulaw stream Audio stream is mixed with video stream Dry Contact Event Count varies from camera models Uses HTTP Server Push mode at 1s interval Unsupported Key Functions • Power Off • Get Lo
Samsung Default Ports • Port 80 for HTTP • Port 554 for RTSP Default Username & Password Username: admin Password: 4321 Limitations • The following models have been tested and confirmed with Samsung SNV-5010, SNZ-5200, SND-3080, SND-5080, SND-7080, SNP-3120, SNP-3371/3302(b), SNP-5200, SPE-400. All other models listed have been confirmed with Samsung to work as designed under the Samsung API but have not been tested by American Dynamics. There may be potential risks when using these non-tested models.
Samsung • For SPE-400, each Samsung encoder's channel has an independent IP. To add an encoder to the NVR, the user should add every channel one by one. Only the first channel supports audio. Each channel supports 1 AlarmIn. • Some of the camera information (e.g. FPS ranges) provided by Samsung Support differs from the camera's actual capabilities as found on the Web Gui. The Handler uses API results for these details.
Samsung zero and start from 1024x768. Then if handler wants to set 1280x720 to camera, the index is '2'. • Handler uses TYPE2 (Samsung different cameras use different APIs, defined in their formal datasheet, named TYPE1 and TYPE2, TYPE2 is used by most cameras) command to communicate with generic camera. • Since most on-sale cameras do not support bitrate feature, generic camera will not support it. • Generic camera does not support PTZ, lens and image settings.
Samsung • If FPS is too low, RTSP connects to camera may timeout and then the NVR will have no video. The following cameras were found to have this issue: • For SNV-5010 and SND-7080, the MJPEG video will not display when the user sets fps to 1 and resolution to less than 1280*720. • For SND-3002 and SND-5080, the MPEG4 video will not display when the user sets FPS to <=5. • Video and audio are sometimes out of sync on Instant Playback and Search & Retrieve in victor.
Samsung 28-6 Camera Handler Release Notes
SONY Supported Key Functions • Video Streaming – Single and Dual • Video Codec – MJPEG, MPEG4 and H.264 • Audio Streaming • Audio codec supported depends on camera functionality • PTZ – applies to cameras with mechanical pan, tilt and optical zoom • Dry contact events – HTTP server push functionality is available for increase in efficiency and speed of obtaining dry contact events.
SONY • Port 554 is for RTSP Default Username & Password • Username: admin • Password: admin Limitations • SONY 5th generation cameras set with motion-detection using MJPEG or MPEG4 will present the limitation that if H.264 has been used for the primary stream, it cannot be used for the secondary. Video Motion Detection is only available on MJPEG video stream.
SONY resolution might not be able to handle the maximum frame-rate even in singlestream use (MPEG4 is less intensive and may handle the maximum frame-rate). • For a secondary stream, the remaining camera processing power and bandwidth can be configured. In a typical application, this would be for motiondetection using MJPEG or MPEG4. • If H.264 has been used for the primary stream, do not use H.264 for the secondary.
SONY 29-4 Camera Handler Release Notes