Operation Guide
Table Of Contents
- VideoJet X40
- Table of Contents
- 1 Preface
- 2 Safety Information
- 3 Product Description
- 4 Installation
- 5 Configuration Using a Web Browser
- 5.1 Connecting
- 5.2 Configuration Menu
- 5.3 Basic Mode: Unit Access
- 5.4 Basic Mode: Date/Time
- 5.5 Basic Mode: Network
- 5.6 Basic Mode: Encoder Profile
- 5.7 Basic Mode: Audio
- 5.8 Basic Mode: Recording
- 5.9 Basic Mode: System Overview
- 5.10 Advanced Mode: Identification
- 5.11 Advanced Mode: Password
- 5.12 Advanced Mode: Date/Time
- 5.13 Advanced Mode: Display Stamping
- 5.14 Advanced Mode: Appearance
- 5.15 Advanced Mode: LIVEPAGE Functions
- 5.16 Advanced Mode: Logging
- 5.17 Advanced Mode: Video Input
- 5.18 Advanced Mode: Picture Settings
- 5.19 Advanced Mode: Encoder Profile
- 5.20 Advanced Mode: Audio
- 5.21 Advanced Mode: Storage Management
- 5.22 Advanced Mode: Remote Video Device
- 5.23 Advanced Mode: Recording Profiles
- 5.24 Advanced Mode: Retention Time
- 5.25 Advanced Mode: Recording Scheduler
- 5.26 Advanced Mode: Recording Status
- 5.27 Advanced Mode: Alarm Connections
- 5.28 Advanced Mode: VCA
- 5.29 Advanced Mode: VCA Profiles
- 5.30 Advanced Mode: VCA Scheduled
- 5.31 Advanced Mode: VCA Event Triggered
- 5.32 Advanced Mode: Audio Alarm
- 5.33 Advanced Mode: Alarm E-Mail
- 5.34 Advanced Mode: Alarm Task Editor
- 5.35 Advanced Mode: Alarm Inputs
- 5.36 Advanced Mode: Relay
- 5.37 Advanced Mode: COM1
- 5.38 Advanced Mode: Network
- 5.39 Advanced Mode: Advanced
- 5.40 Advanced Mode: Multicasting
- 5.41 Advanced Mode: JPEG Posting
- 5.42 Advanced Mode: Encryption
- 5.43 Advanced Mode: Maintenance
- 5.44 Advanced Mode: Licenses
- 5.45 Advanced Mode: System Overview
- 5.46 Function Test
- 6 Operation
- 7 Maintenance and Upgrades
- 8 Appendix
- 9 Specifications
- 10 Glossary
- 11 Index
VideoJet X40 Configuration Using a Web Browser | en 35
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
5.7 Basic Mode: Audio
You can set the gain of the audio signals to suit your specific requirements. The current video
image is shown in the small window next to the slide controls to help you check the selected
audio source and improve assignments. Your changes are effective immediately.
If you connect via Web browser, you must activate the audio transmission on the LIVEPAGE
Functions page (see Section 5.15 Advanced Mode: LIVEPAGE Functions, page 43). For other
connections, the transmission depends on the audio settings of the respective system.
Audio
The audio signals are sent in a separate data stream parallel to the video data, and so increase
the network load. The audio data are encoded according to G.711 and require an additional
bandwidth of approx. 80 kbps for each connection. If you do not want any audio data to be
transmitted, select Off.
Line In
You can set the audio signal gain for the line inputs. Make sure that the display does not go
beyond the green zone during modulation.
Line Out
You can set the line output gain. Make sure that the display does not go beyond the green
zone during modulation.
i
NOTICE!
The numbering of the audio inputs follows the labeling on the unit and the assignment to the
respective video inputs. The assignment cannot be changed for Web browser connections.