Operation Guide
Table Of Contents
- VideoJet X40
- Table of Contents
- 1 Preface
- 2 Safety Information
- 3 Product Description
- 4 Installation
- 5 Configuration Using a Web Browser
- 5.1 Connecting
- 5.2 Configuration Menu
- 5.3 Basic Mode: Unit Access
- 5.4 Basic Mode: Date/Time
- 5.5 Basic Mode: Network
- 5.6 Basic Mode: Encoder Profile
- 5.7 Basic Mode: Audio
- 5.8 Basic Mode: Recording
- 5.9 Basic Mode: System Overview
- 5.10 Advanced Mode: Identification
- 5.11 Advanced Mode: Password
- 5.12 Advanced Mode: Date/Time
- 5.13 Advanced Mode: Display Stamping
- 5.14 Advanced Mode: Appearance
- 5.15 Advanced Mode: LIVEPAGE Functions
- 5.16 Advanced Mode: Logging
- 5.17 Advanced Mode: Video Input
- 5.18 Advanced Mode: Picture Settings
- 5.19 Advanced Mode: Encoder Profile
- 5.20 Advanced Mode: Audio
- 5.21 Advanced Mode: Storage Management
- 5.22 Advanced Mode: Remote Video Device
- 5.23 Advanced Mode: Recording Profiles
- 5.24 Advanced Mode: Retention Time
- 5.25 Advanced Mode: Recording Scheduler
- 5.26 Advanced Mode: Recording Status
- 5.27 Advanced Mode: Alarm Connections
- 5.28 Advanced Mode: VCA
- 5.29 Advanced Mode: VCA Profiles
- 5.30 Advanced Mode: VCA Scheduled
- 5.31 Advanced Mode: VCA Event Triggered
- 5.32 Advanced Mode: Audio Alarm
- 5.33 Advanced Mode: Alarm E-Mail
- 5.34 Advanced Mode: Alarm Task Editor
- 5.35 Advanced Mode: Alarm Inputs
- 5.36 Advanced Mode: Relay
- 5.37 Advanced Mode: COM1
- 5.38 Advanced Mode: Network
- 5.39 Advanced Mode: Advanced
- 5.40 Advanced Mode: Multicasting
- 5.41 Advanced Mode: JPEG Posting
- 5.42 Advanced Mode: Encryption
- 5.43 Advanced Mode: Maintenance
- 5.44 Advanced Mode: Licenses
- 5.45 Advanced Mode: System Overview
- 5.46 Function Test
- 6 Operation
- 7 Maintenance and Upgrades
- 8 Appendix
- 9 Specifications
- 10 Glossary
- 11 Index
VideoJet X40 Configuration Using a Web Browser | en 77
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
5.35 Advanced Mode: Alarm Inputs
You can configure the alarm inputs of the VideoJet X40.
Alarm input
Select Active high if the alarm is to be triggered when the contact closes. Select Active low if
the alarm is to be triggered when the contact opens.
Name
You can enter a name for each alarm input, which is then displayed below the icon for the
alarm input on the LIVEPAGE if configured correctly (see Section 5.15 Advanced Mode:
LIVEPAGE Functions, page 43).
5.36 Advanced Mode: Relay
You can configure the switching behavior of the relay outputs. For each relay, you can specify
an open switch relay (normally closed contact) or a closed switch relay (normally open
contact).
You can also specify whether an output should operate as a bistable or monostable relay. In
bistable mode, the triggered state of the relay is maintained. In monostable mode, you can set
the time after which the relay will return to the idle state.
You can select different events that automatically activate an output. It is possible, for
example, to turn on a floodlight by triggering a motion alarm and then turning the light off
again when the alarm has stopped.
Idle state
Select Open if you want the relay to operate as an NO contact, or select Closed if the relay is
to operate as an NC contact.