3FHJTUFS \R QHZ GHYLF XU 0\%RVFK H RQ QRZ DQG JHW IUHH E HQ CPTDI IP HILWV NF DPN XFMDPNF Washing machine WAT28620AU en Instruction Manual and Installation Instructions
Your new washing machine Display rules You have chosen a Bosch washing machine. : Warning! Please take a few minutes to read and become familiar with the advantages of your washing machine. This combination of symbol and signal word indicates a possibly dangerous situation. Not heeding the warning can cause death or injuries.
en Contents enI structionManual ndInstal tionI structions 8 Intended use. . . . . . . . . . . . . . . . .5 ( Safety instructions . . . . . . . . . . .5 Detergent . . . . . . . . . . . . . . . . . . 25 Correct selection of detergent . . . . . .25 Saving energy and detergent . . . . . .25 Children/people/pets . Installation. . . . . . . . . . Operation . . . . . . . . . . Cleaning/Maintenance Programme overview . . . . . . . . 26 Possible program settings. . . . . . . . .28 . . . . . . . . . . . . .
en a Intelligent dosing system. . . . . 35 Familiarising yourself with i-DOS . . . 35 i-DOS Detergent drawer. . . . . . . . . . 35 Before setting up i-DOS . . . . . . . . . . 36 Automatic dosing. . . . . . . . . . . . . . . 36 i-DOSSetting the content of the M/w dispenser. . . . . . . . . . . . . . . . . . . . . 36 i-DOS Setting the dosage . . . . . . . . 37 Filling the dispensers. . . . . . . . . . . . 37 Manual dosing . . . . . . . . . . . . . . . . .
Intended use 8 Intended use ■ Intedus ■ ■ ■ ■ This appliance is intended for private domestic use only. Do not install or operate this appliance anywhere that is liable to experience frost and/or outdoor conditions. There is a risk that the appliance will be damaged if residual water in it freezes. If hoses freeze up, they may crack/burst. This appliance must only be used for washing domestic laundry, consisting of machine-washable items and hand-washable woollens (see label on item).
en ■ ■ ■ Safety instructions Do not allow children to clean or maintain this appliance unsupervised. Keep children under 3 years and pets away from this appliance. Do not leave the appliance unattended when children or other people who are unable to assess the risks are in the vicinity. : Warning Risk of death! Children may lock themselves inside appliances and find themselves in a life-threatening situation.
Safety instructions dangerous situation. Ensure the following: ■ ■ ■ ■ ■ The mains voltage on your power socket must match the rated voltage specified on the appliance (identification plate). The connected loads and the required fuse protection are specified on the identification plate. The mains plug and the protective contact socket must match and the earthing system must be correctly installed. The installation must have an adequate cross section.
en ■ Safety instructions If you take hold of any of the appliance's protruding parts (e.g. the appliance door) in order to lift or move it, these parts may break off and cause injury. Do not take hold of any of the appliance's protruding parts in order to move the appliance. : Warning Risk of injury! ■ The appliance is very heavy. Lifting it may result in injury. Do not lift the appliance on your own. Risk of inThe jury! ■ appliance has sharp edges on which you could cut your hands.
Safety instructions ■ The appliance is secured for transportation by transport locking devices. If the transport locking devices are not removed before the appliance is operated, this may result in damage to the appliance. It is important to completely remove all transport locking devices before using the appliance for the first time. Make sure that you retain these transport locking devices separately.
en Safety instructions drawer is opened while the appliance is in operation. Rinse eyes/skin thoroughly if they/it come(s) into contact with detergents or care products. If accidentally swallowed, seek medical advice. Caution! Material damage/damage to the appliance ■ If the amount of laundry in the appliance exceeds its maximum load capacity, it may not be able to operate properly, or this may result in material damage or damage to the appliance. Do not exceed the maximum load capacity of dry laundry.
Environmental protection Do not use cleaning agents that contain solvents. : Warning Risk of electric shock/material damage/damage to the appliance! If moisture penetrates the appliance, this may cause it to short circuit. Do not use a pressure washer, steam cleaner, hose or spray gun to clean your appliance.
en ■ ■ Positioning and connecting The selectable temperatures apply to the care labels on the textiles. The temperatures in the machine may deviate from this so that you get the optimum mix of energy-saving and washing results. Energy- and water-consumption information: These indicators tell you what the relative energy and water consumption is for the selected programs. The more indicator segments are visible, the higher the consumption.
Positioning and connecting 8 Water supply hose on aquaStop models @ H Water drain hose Elbow for securing the water drain hose* Water supply hose on standard/ AquaSecure models * Depending on the model P In addition, a hose clamp (24 - 40 mm diameter, available from specialist retailers) is required to connect the water drain hose to a siphon.
en Positioning and connecting Installation on a platform with drawer Note: Keep the screws and sleeves in a safe place. Platform order no.: WMZ 20490, WZ 20490, WZ 20510, WZ 20520 Installing the appliance in a kitchenette : Warning Danger of death! There is a risk of electric shock if you touch live components. Do not remove the appliance covering plate. Notes ■ Recess width of 60 cm required.
Positioning and connecting Hose and cable lengths ■ Left-hand connection a FP PD[ FP a FP Right-hand connection a FP a FP PD[ FP a FP Tip: The following are available from specialist dealers/the after-sales service: ■ An extension for Aqua-Stop or cold water supply hose (approx. 2.50 m); order no. WMZ2380, WZ10130, CZ11350, Z7070X0 ■ A longer supply hose (approx. 2.
en Positioning and connecting Connection Water outlet Connect the water supply hose to the tap (26.4 mm = ¾") and to the appliance (not necessary for Aqua-Stop models as this is permanently installed): ■ Model: Standard : Warning ■ ■ Model: Aqua-Secure Model: Aqua-Stop Note: Turn on the tap carefully, checking the leak tightness of the connection points. The screw connection is under mains water pressure.
Positioning and connecting Connection ■ ■ Drainage into a siphon The connection point must be secured using a hose clamp with a diameter of 24–40 mm (available from specialist dealers). en 2. Check the alignment of the washing machine with a spirit level, and adjust it if necessary. Change the height by turning the appliance feet. All four appliance feet must stand firmly on the ground. 3. Tighten the lock nut against the housing. In doing so, hold the foot tight and do not adjust its height.
en ■ ■ ■ ■ ■ ■ ■ ■ Positioning and connecting The mains plug fits the socket. The cable cross-section is adequate. The earthing system is properly installed. The mains cable is only replaced by a qualified electrician (if this is necessary). Replacement mains cables are available from the aftersales service. No multiple plugs/couplings or extension cables are used. If an earth-leakage circuit breaker is used, only a type which displays this symbol is used: z.
Positioning and connecting Transportation E.g. when moving house Preparatory work: 1. Turn off the tap. 2. Release the water pressure in the supply hose: ~ "Filter in the water supply blocked" on page 44 3. Disconnect the washing machine from the mains power supply. 4. Drain the remaining water: ~ "The drain pump is blocked, emergency draining" on page 43 5. Detach the hoses. 6. Empty the dispensers.
en Familiarising yourself with your appliance * Familiarising yourself with your appliance Washing machine mFail arisngyourself withyouraplince # 6 7 Detergent drawer ~ Page 33 Controls Washing machine door with handle 9S Opening the washing machine door 9T Closing the washing machine door ( 0 8 20 @ Service flap
Familiarising yourself with your appliance en Controls ( Main switch You can use the # button to switch the appliance on and off. 0 Programme selector You can turn the programme selector in both directions (clockwise and anti-clockwise). 8 Touch display This shows you the programme information and selection options for settings, and you can select the settings by touching the framed or underlined areas. Content of the touch display The display on this appliance responds to touch (touch display).
en Familiarising yourself with your appliance Indicators, symbols and buttons Indicators and Setting on the control panel symbols for setting values 90°, 60° ü, 40° ü, 30°, 20°, — Temperature in °C; — = cold 1400*, 1200, 800, 600, 400, 2 Spin speed; 2 = no spin ý i-DOS w w Automatically dispenses liquid detergent þ i-DOS M/w M/w Automatically dispenses fabric softener or liquid detergent; set the dispenser content ~ Page 36 O +1, +2, +3, Off Aqua Plus; + additional rinse cycles SpeedPerfect Q
Familiarising yourself with your appliance en Indicators, symbols and buttons Indicators and Setting on the control panel symbols for setting values Start/Pause A For changing the setting values Note: Where there are multiple setting values, pressing and holding N, M will allow you to automatically scroll through all the setting values to the last value. Touching it again will allow you to change the setting values again.
en Laundry Z Laundry Prepare the laundry Laundry Caution! Damage to the appliance/fabrics Foreign objects (e.g. coins, paperclips, needles, nails) may damage the laundry or components in the washing machine. You should therefore note the following tips when preparing your laundry: ■ Empty any pockets. ■ ■ ■ ■ ■ ■ Look out for metal items (paperclips, etc.) and remove them. Wash delicates in a laundry bag (tights, underwired bras, etc.). Close any zips; button up any cover buttons.
Detergent Dyeing/bleaching Dye should only be used in normal household quantities. Salt may damage stainless steel. Always follow the dye manufacturer's instructions. Do not use the washing machine to bleach clothes. C Detergent Correct selection of detergent Detrgn The care label is crucial for selecting the correct detergent, temperature and treatment of the laundry. ~ See also www.sartex.ch If you visit www.cleanright.
en Programme overview / Programme overview Progameovriew Programmes and fabrics Maximum load size Use softener? Cottons i Hard-wearing items made from cotton, linen or blended fabrics. When used for a light load (* max. 5 kg) with the SpeedPerfect setting, this programme is suitable as a quick programme for lightly soiled laundry. 8 kg/5 kg* Yes Cottons Eco 0 8 kg Hard-wearing items made from cotton, linen or blended fabrics.
Programme overview Rinse / Spin / Drain ' / 0 / [ ~ Combined programme: Rinses and then spins the laundry, and then pumps out the water. Notes ■ The Rinse programme, after which the laundry is spun and the water is pumped out, has been preactivated. ■ If you only want to rinse the laundry and pump out the water, set the spin speed to 0. ■ If you only want to spin the laundry and pump out the water, deactivate the Rinse Plus O setting.
en Programme overview Sportswear w 2 kg Sportswear and leisurewear made from synthetic or microfibre fabrics or fleece. Note: Use an Easy-Care programme to wash heavily soiled laundry. No Clean the compartment for manual dosing in the detergent drawer before washing. AllergyPlus ; 6,5 kg Hard-wearing items made from cotton, linen or blended fabrics. Suitable for allergy sufferers and for strict hygiene requirements.
Programme default settings Max. temperature Max.
en Additional programme settings and counted down until the washing programme starts. The duration of the programme is then displayed. Note: The programme duration is automatically adjusted when the programme is running. Changes to the programme default settings or programme settings, foam detection function, unbalanced load detection, the load or soiling may also change the programme duration. After the programme starts, and while the selected time is counting down, you can change this as follows: 1.
Additional programme settings Reduced Ironing Q Reduces creasing thanks to a special spin sequence followed by fluffing and reduced spin speed. Note: The washing's residual moisture is increased. Prewash T For heavily soiled laundry. Notes ■ If automatic dosing (i-DOS) is selected, detergent will be dispensed automatically for the prewash and main wash cycles. ■ If manual dosing is selected, you will need to allocate detergent for the prewash and main wash cycles.
en Operating the appliance 1 Operating the appliance Preparing the washing machine Operatingheaplince Note: The washing machine must be correctly installed and connected. From ~ Page 12 1. 2. 3. 4. Connect the mains plug. Turn on the water tap. Open the door. Check that the drum is completely drained. Drain if necessary. In appliances with drum interior lighting: The drum is lit after switching on the appliance, after opening and closing the door and after starting a programme.
Operating the appliance Placing laundry into the drum : Warning Danger of death! Items of laundry pretreated with cleaning agents that contain solvents, e.g. stain remover/cleaning solvent, may cause an explosion after being loaded into the washing machine. Hand-rinse these items of laundry thoroughly beforehand. Notes Mix items of laundry of varying sizes.Laundry items of different sizes distribute themselves better during the spin cycle.Individual laundry items may cause an unbalanced load.
en Operating the appliance Child lock 3 sec./operation lock E 3 sec. You can lock the washing machine to prevent the functions you have set from being changed inadvertently in the control panel. To activate/deactivate the childproof lock, touch and hold the control panel E 3 sec. for approx. three seconds. The display switches to full brightness. If you turn the programme selector or touch the control panel while the childproof lock is active, the E 3 sec. indicator flashes briefly and a signal sounds.
Intelligent dosing system ■ ■ Selecting the Reduced Ironing Q setting and then touching A or Turning the programme selector to Drain and then touching A. Programme end End lights up in the display panel and the A and è displays are off. Note: If the Û display flashes, this informs you to run the Drum Clean Û programme or any other programme at a washing temperature of at least 60 °C. Removing laundry/switching off the appliance 1. Open the loading door and remove the laundry. 2. Switch off the appliance.
en Intelligent dosing system Before setting up i-DOS Follow the manufacturer's instructions when choosing your detergent and care product. We recommend using easypour, all-purpose, universal and colour liquid detergents for all machinewashable, coloured items made of cotton or synthetic fabrics. Notes ■ Only use easy-pour liquid products that the manufacturer recommends adding to the detergent drawer. ■ When cleaning the i-DOS detergent drawer, empty the dispenser completely and clean it.
Intelligent dosing system Note: If both dispensers are filled with liquid detergent, only the dispenser that was activated by choosing the i-DOS button is used during the wash cycle. i-DOS Setting the dosage The basic dosage is the recommended dosage for a typical load of household laundry weighing 4.5 kg. The quantity of detergent and care product actually dispensed is calculated using the basic dosage and the amount of laundry, which is detected automatically.
en Intelligent dosing system 2. Open the dispenser lids. 3. Pour liquid detergent and fabric softener into the relevant dispensers. Notes – Do not fill the dispensers above the max. mark. – Follow the instructions in chapters ~ "i-DOS Setting the dosage" on page 37 and ~ "iDOSSetting the content of the M/w dispenser" on page 36. 4. Close the dispenser lids. Note: To prevent the detergent drying out or drying up, do not leave the dispenser lids open for a long period of time. 5.
Intelligent dosing system Dosing and adding detergent Note: Find out the optimum dosage for detergent and care product. 1. Pull out the detergent drawer. en Emptying the i-DOS detergent drawer, cleaning the i-DOS detergent drawer and its housing, cleaning the i-DOS pump unit 1. Switch off the appliance. 2. Pull out the detergent drawer. 2. Pour laundry detergent and/or care product into the manual dosing compartment. 3. Press down the insert and remove the drawer completely. 3.
en Intelligent dosing system 5. Unclip the rear detergent drawer lid and remove it. 6. Empty the detergent drawer. 8. Clean the drawer, inside surface and lids with a soft, damp cloth or a hand shower. 9. Dry the drawer, lids and pump unit and put them back together. 7. Clean the pump unit with a damp cloth. Caution! The pump unit contains electrical components.These may be damaged if they come into contact with water. – Do not clean the pump unit in the dishwasher and do not immerse it in water.
Appliance settings 11. Push in the detergent drawer. Q Appliance settings You can change the following settings in the control and display panel: ■ The volume of the information signal (e.g. at the end of the programme), ■ The volume of the operating signals, ■ The brightness of the operating and display field, ■ Select/deselect the memory function for drum care. Apliancest ings You will need to activate the setting mode in order to change these settings. Activating the setting mode 1.
en Sensors Exiting setting mode VoltCheck To exit and save the settings: ■ Wait for approx. 15 minutes or ■ Touch œ one last time or ■ Switch off the appliance. The selected settings will take effect the next time the washing machine is switched on. depending on the model The colon in the ready in // (Ready in) / / Finished in display: ■ Flashes , if the voltage is currently too low. ■ Pulses, if insufficient voltage was detected during the programme.
Cleaning and maintenance Caution! Damage to the appliance Cleaning agents that contain solvents, e.g. cleaning solvent, can damage surfaces and components in the machine. Do not use cleaning agents that contain solvents. Prevent detergent residue from building up and odours from forming by following these instructions: Notes Ensure the room in which the washing machine is set up is well ventilated. ■ Leave the door and detergent dispenser tray open slightly when the washing machine is not in use.
en Cleaning and maintenance Refit the pump cover and screw it on tightly.The handle must be positioned vertically. 4. Re-attach the drain hose and secure the connection point using the hose clamp. Filter in the water supply blocked 6. Reinsert the bottom of the service flap into the slot, clip it into place and close the flap. Note: To prevent unused detergent from flowing straight into the drain during the next wash, pour 1 litre of water into the manual dosing compartment and start the Drain program.
Faults and what to do about them. 3 Faults and what to do about them. Emergency release Faultsandwht odabut hem. E.g. in the event of a power cut The programme continues when the power supply is restored. However, if the laundry has to be removed, the washing machine door can be opened as follows: : Warning en Wait until the drum has stopped turning. Caution! Water damage Any escaping water may cause water damage. Do not open the door if water can be seen through the glass. 1.
en Faults and what to do about them. Display Cause/remedy r is flashing The appliance is not being supplied with water: ■ Turn the tap on fully, ■ The supply hose is kinked/trapped, ■ Clean the filter if necessary. ~ Page 44 E 3 sec. is continuously lit The childproof lock is activated – deactivate it. ~ Page 34 E 3 sec. is flashing The childproof lock is activated – the programme selector has been turned or the control panel touched.
Faults and what to do about them. en Faults and what to do about them. Faults Water is leaking from the machine. The programme has started and the drum is rotating, but the drum is not filling with water. The machine is not filling with water. Detergent is not being dispensed. The door cannot be opened. Cause/remedy ■ ■ Not a fault – the load is automatically detected after the programme has started in order to calculate the optimum amount of water for washing.
en Faults and what to do about them. Faults Foam is leaking from the detergent drawer. Cause/remedy ■ ■ ■ Repeated, intensive foaming. ■ ■ Automatic dosing: i-DOS Check the dosage settings and, if required, reduce the basic dosage. ~ "i-DOS Setting the dosage" on page 37 If required, use a different liquid detergent/fabric softener. Manual dosing: Have you used too much detergent? Use less detergent in the next wash cycle.
Faults and what to do about them. Faults The programme is taking longer than usual. en Cause/remedy ■ ■ Not a fault – the unbalanced load detection system is eliminating an imbalance by repeatedly redistributing the laundry. Not a fault – the foam detection system is active; this adds an additional rinse cycle. The duration of the programme changes during the wash cycle. Not a fault – the programme sequence is optimised for the specific washing process.
en Consumption values [ Consumption values (approximate values) Consumptionvalues Programme Load Energy consumption* Water consumption* Programme duration* Cottons 20 °C 8 kg 0,35 kWh 86 l 3^h Cotton 40 °C 8 kg 0,72 kWh 65 l 2_h Cottons 60 °C 8 kg 1,29 kWh 65 l 2_h Cottons Eco + ú ** 8 kg 0,55 kWh 58 l 4]h Cottons 90 °C 8 kg 2,30 kWh 75 l 2_h Easy Care 40 °C 4 kg 0,76 kWh 61 l 2^h Mix 40 °C 4 kg 0,62 kWh 43 l 1h Delicates / Silk 30 °C 2 kg 0,20 kWh 35 l _h Wo
Consumption values en Information for test institute Items Pre-treatment of new appliance According to standard Washing programme Testing instructions Age of test loads Loading Procedure No. of Layers External circle Layer1 Layer2 Layer3 Layer4 Layer5 Instruction Run two empty runs of Cottons i 90 °C with 1400 rpm: The 1st run with 50g IEC B detergent and 50g anti sudsing agent, the 2nd run without detergent and sudsing agent. AS NZS 2040.1-2005 AS NZS 2040.
en Technical data J Technical data Dimensions: 850 x 600 x 590 mm (height x width x depth) Weight: 70 - 85 kg (depending on model) Mains connection: Mains voltage 220 - 240 V, 50 Hz Nominal current 10 A Nominal power 1900 – 2300 W Water pressure: 100 - 1000 kPa (1 - 10 bar) Power consumption when switched off: 0,10 W Power consumption when left on: 0,10 W cTehnialdt 52 4 After-sales service If you cannot rectify a fault yourself, contact customer services.
Aqua-Stop warranty en r Aqua-Stop warranty Only for appliances with Aqua-Stop Aqua-Stopwarnty In addition to warranty claims against the vendor based on the purchase agreement and to our appliance warranty, we will provide compensation under the following conditions: 1. If water damage is caused due to a fault in our Aqua-Stop system, we will compensate domestic customers for the damage caused. 2. The liability guarantee is valid for the service life of the appliance. 3.
6
6
Thank you for buying a Bosch Home Appliance! Register your new device on MyBosch now and profit directly from: • • • • • Expert tips & tricks for your appliance Warranty extension options Discounts for accessories & spare-parts Digital manual and all appliance data at hand Easy access to Bosch Home Appliances Service Free and easy registration – also on mobile phones: www.bosch-home.com/welcome Looking for help? You´ll find it here.
