User's Manual
Table Of Contents
- en Instruction Manual and Installation Instructions
- Display rules
- : Warning!
- Caution!
- Note/tip
- 1. 2. 3. / a) b) c)
- Contentsen Instruction Manual and Installation Instructions
- 8 Intended use 5
- ( Safety instructions 5
- 7 Environmental protection 11
- 5 Positioning and connecting 12
- * Familiarising yourself with your appliance 20
- Z Laundry 24
- C Detergent 25
- / Programme overview 26
- 0 Programme default settings 29
- \ Additional programme settings 30
- 1 Operating the appliance 32
- a Intelligent dosing system 35
- Q Appliance settings 41
- H Sensors 42
- 2 Cleaning and maintenance 42
- 3 Faults and what to do about them. 45
- [ Consumption values 50
- J Technical data 52
- 4 After-sales service 52
- r Aqua-Stop warranty 53
- 8 Intended use
- Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Caution!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Positioning and connecting
- Positioning and connecting
- Included with the appliance
- Safety instructions
- Installation surface
- Installation on a base or a wooden joist floor
- Installation on a platform with drawer
- Installing the appliance in a kitchenette
- Removing the transport locks
- 2. Unscrew and remove all four transport brace screws.
- 3. Fit the covers. Lock the covers firmly in place by applying pressure to the snap-in hooks.
- Connection
- Connection
- Preparatory work:
- Run the program without laundry:
- 1. Switch on the appliance.
- 2. Close the door (do not load any laundry).
- 3. Set the Drum Clean Û 90 °C program.
- 4. Open the detergent drawer.
- 5. Pour approx. 1 litre of water into the manual dosing compartment.
- 6. Pour all-purpose detergent into the manual dosing compartment.
- 7. Close the detergent drawer.
- 8. Start the program.
- 9. Switch off the appliance once the program has finished.
- 2. Release the water pressure in the supply hose: ~ "Filter in the water supply blocked" on page 44
- 3. Disconnect the washing machine from the mains power supply.
- 4. Drain the remaining water: ~ "The drain pump is blocked, emergency draining" on page 43
- 5. Detach the hoses.
- 6. Empty the dispensers. ~ Page 39
- Fitting the transportation securing means:
- * Familiarising yourself with your appliance
- Familiarising yourself with your appliance
- Washing machine
- Controls
- Content of the touch display
- Z Laundry
- C Detergent
- / Programme overview
- Programme overview
- Programmes and fabrics
- Maximum load size
- Use softener?
- Notes
- Note:
- Notes
- Notes
- Notes
- Note:
- Note:
- Note:
- Possible program settings
- 0 Programme default settings
- \ Additional programme settings
- Additional programme settings
- Aqua Plus
- SpeedPerfect
- Reduced Ironing
- Prewash
- Soaking
- 2. Select the Cottons i 30 °C program and press the A button.
- 3. Press the A button after approx. 10 minutes.The laundry will soak in the water.
- 4. Leave the laundry to soak for as long as required, then either press the A button again to resume the program or change the program.
- 1 Operating the appliance
- Operating the appliance
- Preparing the washing machine
- 2. Turn on the water tap.
- 3. Open the door.
- 4. Check that the drum is completely drained. Drain if necessary.
- You can:
- The current programme information is displayed during the programme:
- Note:
- Child lock 3 sec./operation lock
- Adding laundry
- Changing the programme
- 2. Select another programme.
- 3. And touch A again.The new program starts from the beginning.
- 2. To cool the laundry: Select Rinse.
- 3. And touch A again.
- 2. Select Spin or Drain.
- 3. And touch A again.
- 2. Switch off the appliance.
- 3. Turn off the tap.
- a Intelligent dosing system
- Intelligent dosing system
- Familiarising yourself with i- DOS
- i-DOS Detergent drawer
- Before setting up i-DOS
- Automatic dosing
- The automatic dosage operates as follows:
- Set the dispenser content as follows:
- Check whether the preset basic dosages follow the manufacturer's recommendations in terms of:
- Below is an example of detergent dosages on a packaging label:
- Adjusting the basic dosage
- Fill the dispensers as follows:
- Dosing and adding detergent
- Note:
- 2. Pour laundry detergent and/or care product into the manual dosing compartment.
- 3. Push in the detergent drawer.
- 2. Pull out the detergent drawer.
- 3. Press down the insert and remove the drawer completely.
- 4. Press the pump unit insert and remove it.
- 5. Unclip the rear detergent drawer lid and remove it.
- 6. Empty the detergent drawer.
- 7. Clean the pump unit with a damp cloth.
- 8. Clean the drawer, inside surface and lids with a soft, damp cloth or a hand shower.
- 9. Dry the drawer, lids and pump unit and put them back together.
- 10. Clean the inside of the detergent drawer housing.
- 11. Push in the detergent drawer.
- Q Appliance settings
- H Sensors
- 2 Cleaning and maintenance
- Cleaning and maintenance
- : Warning
- Danger of death!
- : Warning
- Risk of poisoning!
- Caution!
- Damage to the appliance
- Notes
- Machine housing/control panel
- Drum
- Descaling
- The drain pump is blocked, emergency draining
- 2. Switch off the appliance.Pull out the mains plug.
- 3. Open and remove the service flap.
- 4. Take the drain hose out of the holder.
- 5. Carefully unscrew the pump cover, as residual water may leak out.
- 6. Reinsert the bottom of the service flap into the slot, clip it into place and close the flap.
- 2. Loosen the hose clamp. Carefully remove the drain hose; residual water may leak out.
- 3. Clean the drain hose and siphon connecting piece.
- 4. Re-attach the drain hose and secure the connection point using the hose clamp.
- 2. Clean the filters:
- 3 Faults and what to do about them.
- [ Consumption values
- J Technical data
- 4 After-sales service
- r Aqua-Stop warranty
- Aqua-Stop warranty
- 2. The liability guarantee is valid for the service life of the appliance.
- 3. It is a prerequisite of all warranty claims that the appliance with Aqua- Stop must have been installed and connected correctly in accordance with our instructions; this also includes a correctly fitted Aqua-Stop extension (genuine accessories).
- 4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured afterwards by turning off the tap.
en Positioning and connecting
18
■ The mains plug fits the socket.
■ The cable cross-section is adequate.
■ The earthing system is properly
installed.
■ The mains cable is only replaced by
a qualified electrician (if this is
necessary). Replacement mains
cables are available from the after-
sales service.
■ No multiple plugs/couplings or
extension cables are used.
■ If an earth-leakage circuit breaker is
used, only a type which displays this
symbol is used: z.
Only this symbol guarantees
compliance with the currently
applicable regulations.
■ The mains plug must be freely
accessible at all times. If this is not
possible, in order to comply with the
relevant safety regulations, a switch
(2-pole switch-off) must be built into
the permanent installation in
accordance with electrical
installation regulations.
■ The mains cable is not bent,
squashed, modified, cut through, or
in contact with heat sources.
Before washing for the first
time
The washing machine has been
thoroughly tested before leaving the
factory.To remove any water that may
be left over from testing, run the first
wash cycle without any laundry.
Notes
■ The washing machine must be
correctly installed and connected.
See ~ Page 12 onwards
■ Never use a damaged machine.
Notify your after-sales service.
Preparatory work:
1. Check the machine.
2. Fill the w and M dispensers.
~ Page 37
3. Remove the protective film from the
control panel.
4. Plug in the mains plug.
5. Turn on the tap.
Run the program without laundry:
1. Switch on the appliance.
2. Close the door (do not load any
laundry).
3. Set the Drum Clean Û 90 °C
program.
4. Open the detergent drawer.
5. Pour approx. 1 litre of water into the
manual dosing compartment.
6. Pour all-purpose detergent into the
manual dosing compartment.
Note: To prevent foaming, only use
half the amount of detergent
recommended by the detergent
manufacturer.Do not use detergents
intended for woollens or delicates.
7. Close the detergent drawer.
8. Start the program.
9. Switch off the appliance once the
program has finished.
Your washing machine is now ready to
use.