User's Manual
Table Of Contents
- en Instruction Manual and Installation Instructions
- Display rules
- : Warning!
- Caution!
- Note/tip
- 1. 2. 3. / a) b) c)
- Contentsen Instruction Manual and Installation Instructions
- 8 Intended use 5
- ( Safety instructions 5
- 7 Environmental protection 11
- 5 Positioning and connecting 12
- * Familiarising yourself with your appliance 20
- Z Laundry 24
- C Detergent 25
- / Programme overview 26
- 0 Programme default settings 29
- \ Additional programme settings 30
- 1 Operating the appliance 32
- a Intelligent dosing system 35
- Q Appliance settings 41
- H Sensors 42
- 2 Cleaning and maintenance 42
- 3 Faults and what to do about them. 45
- [ Consumption values 50
- J Technical data 52
- 4 After-sales service 52
- r Aqua-Stop warranty 53
- 8 Intended use
- Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Caution!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Positioning and connecting
- Positioning and connecting
- Included with the appliance
- Safety instructions
- Installation surface
- Installation on a base or a wooden joist floor
- Installation on a platform with drawer
- Installing the appliance in a kitchenette
- Removing the transport locks
- 2. Unscrew and remove all four transport brace screws.
- 3. Fit the covers. Lock the covers firmly in place by applying pressure to the snap-in hooks.
- Connection
- Connection
- Preparatory work:
- Run the program without laundry:
- 1. Switch on the appliance.
- 2. Close the door (do not load any laundry).
- 3. Set the Drum Clean Û 90 °C program.
- 4. Open the detergent drawer.
- 5. Pour approx. 1 litre of water into the manual dosing compartment.
- 6. Pour all-purpose detergent into the manual dosing compartment.
- 7. Close the detergent drawer.
- 8. Start the program.
- 9. Switch off the appliance once the program has finished.
- 2. Release the water pressure in the supply hose: ~ "Filter in the water supply blocked" on page 44
- 3. Disconnect the washing machine from the mains power supply.
- 4. Drain the remaining water: ~ "The drain pump is blocked, emergency draining" on page 43
- 5. Detach the hoses.
- 6. Empty the dispensers. ~ Page 39
- Fitting the transportation securing means:
- * Familiarising yourself with your appliance
- Familiarising yourself with your appliance
- Washing machine
- Controls
- Content of the touch display
- Z Laundry
- C Detergent
- / Programme overview
- Programme overview
- Programmes and fabrics
- Maximum load size
- Use softener?
- Notes
- Note:
- Notes
- Notes
- Notes
- Note:
- Note:
- Note:
- Possible program settings
- 0 Programme default settings
- \ Additional programme settings
- Additional programme settings
- Aqua Plus
- SpeedPerfect
- Reduced Ironing
- Prewash
- Soaking
- 2. Select the Cottons i 30 °C program and press the A button.
- 3. Press the A button after approx. 10 minutes.The laundry will soak in the water.
- 4. Leave the laundry to soak for as long as required, then either press the A button again to resume the program or change the program.
- 1 Operating the appliance
- Operating the appliance
- Preparing the washing machine
- 2. Turn on the water tap.
- 3. Open the door.
- 4. Check that the drum is completely drained. Drain if necessary.
- You can:
- The current programme information is displayed during the programme:
- Note:
- Child lock 3 sec./operation lock
- Adding laundry
- Changing the programme
- 2. Select another programme.
- 3. And touch A again.The new program starts from the beginning.
- 2. To cool the laundry: Select Rinse.
- 3. And touch A again.
- 2. Select Spin or Drain.
- 3. And touch A again.
- 2. Switch off the appliance.
- 3. Turn off the tap.
- a Intelligent dosing system
- Intelligent dosing system
- Familiarising yourself with i- DOS
- i-DOS Detergent drawer
- Before setting up i-DOS
- Automatic dosing
- The automatic dosage operates as follows:
- Set the dispenser content as follows:
- Check whether the preset basic dosages follow the manufacturer's recommendations in terms of:
- Below is an example of detergent dosages on a packaging label:
- Adjusting the basic dosage
- Fill the dispensers as follows:
- Dosing and adding detergent
- Note:
- 2. Pour laundry detergent and/or care product into the manual dosing compartment.
- 3. Push in the detergent drawer.
- 2. Pull out the detergent drawer.
- 3. Press down the insert and remove the drawer completely.
- 4. Press the pump unit insert and remove it.
- 5. Unclip the rear detergent drawer lid and remove it.
- 6. Empty the detergent drawer.
- 7. Clean the pump unit with a damp cloth.
- 8. Clean the drawer, inside surface and lids with a soft, damp cloth or a hand shower.
- 9. Dry the drawer, lids and pump unit and put them back together.
- 10. Clean the inside of the detergent drawer housing.
- 11. Push in the detergent drawer.
- Q Appliance settings
- H Sensors
- 2 Cleaning and maintenance
- Cleaning and maintenance
- : Warning
- Danger of death!
- : Warning
- Risk of poisoning!
- Caution!
- Damage to the appliance
- Notes
- Machine housing/control panel
- Drum
- Descaling
- The drain pump is blocked, emergency draining
- 2. Switch off the appliance.Pull out the mains plug.
- 3. Open and remove the service flap.
- 4. Take the drain hose out of the holder.
- 5. Carefully unscrew the pump cover, as residual water may leak out.
- 6. Reinsert the bottom of the service flap into the slot, clip it into place and close the flap.
- 2. Loosen the hose clamp. Carefully remove the drain hose; residual water may leak out.
- 3. Clean the drain hose and siphon connecting piece.
- 4. Re-attach the drain hose and secure the connection point using the hose clamp.
- 2. Clean the filters:
- 3 Faults and what to do about them.
- [ Consumption values
- J Technical data
- 4 After-sales service
- r Aqua-Stop warranty
- Aqua-Stop warranty
- 2. The liability guarantee is valid for the service life of the appliance.
- 3. It is a prerequisite of all warranty claims that the appliance with Aqua- Stop must have been installed and connected correctly in accordance with our instructions; this also includes a correctly fitted Aqua-Stop extension (genuine accessories).
- 4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured afterwards by turning off the tap.
Intelligent dosing system en
37
Note: If both dispensers are filled with
liquid detergent, only the dispenser that
was activated by choosing the i-DOS
button is used during the wash cycle.
i-DOS Setting the dosage
The basic dosage is the recommended
dosage for a typical load of household
laundry weighing 4.5 kg. The quantity of
detergent and care product actually
dispensed is calculated using the basic
dosage and the amount of laundry,
which is detected automatically.
The basic dosages for liquid detergent
and fabric softener are set at the
factory. You can individually adjust the
basic dosages for each dispenser.
Check whether the preset basic
dosages follow the manufacturer's
recommendations in terms of:
■ A 4.5 kg load
■ For liquid detergent – the normal
degree of soiling and the relevant
water hardness
■ For fabric softener – the medium
softness
Refer to the packaging label on your
liquid detergent/fabric softener or ask
the manufacturer directly for this
information.
Below is an example of detergent
dosages on a packaging label:
If necessary, adjust the basic dosages
to the recommended load for the liquid
detergent/care product you are using,
the water hardness and/or the degree
of soiling.
Adjusting the basic dosage
1. Press and hold ý i-DOS w and/or
þ i-DOS M/w for approx. 3
seconds.
The basic dosage setting will be
displayed.
2. Change the setting using: ˜/~
3. To exit setting mode, press and hold
ý i-DOS w and/or þ i-DOS M/w
for approx. 3 seconds or wait
approx. 10 seconds.
Notes
■ The changes are applied to all
programmes in which dosing is
possible.
■ The changes are saved until the next
time they are changed and are
retained even after the appliance has
been switched off.
Filling the dispensers
Notes
■ See the instructions in chapter
~ "Before setting up i-DOS"
on page 36
■ If w or M flashes, fill the relevant
dispenser. ~ Page 35
Fill the dispensers as follows:
1. Pull out the detergent drawer.
For standard load
4 - 5 kg
Level of soiling
light normal heavy
Water
hardness
soft/
medium
40 ml 55 ml 80 ml
hard/
very
hard
55 ml 80 ml 105 ml
In this example, a basic dosage of 55 ml must be
set for a medium water hardness.