Use and Care Manual
Table Of Contents
- en Instruction Manual and Installation Instructions
- Contentsen Instruction Manual and Installation Instructions
- 8 Intended use 4
- ( Safety instructions 5
- 7 Environmental protection 11
- 5 Positioning and connecting 12
- * Familiarising yourself with your appliance 19
- Z Laundry 22
- C Detergent 23
- 0 Programme default settings 24
- \ Additional programme settings 26
- 1 Operating the appliance 27
- a Intelligent dosing system 31
- H Sensors 36
- Q Appliance settings 37
- 2 Cleaning and maintenance 38
- 3 Faults and what to do about them. 40
- 4 After-sales service 45
- J Technical data 45
- r Aqua-Stop warranty 46
- 8 Intended use
- Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Caution!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Positioning and connecting
- Positioning and connecting
- Included with the appliance
- Safety instructions
- Installation surface
- Installation on a base or a wooden joist floor
- Installation on a platform with drawer
- Installing the appliance in a kitchenette
- Removing the transport locks
- Hose and cable lengths
- Water inlet
- Water outlet
- Levelling
- Electrical connection
- Before washing for the first time
- Notes
- Preparatory work:
- Run the program without laundry:
- 1. Switch on the appliance.
- 2. Close the door (do not load any laundry).
- 3. Depending on the model, set the Drum Clean 90 °C or Cottons//Cotton 90 °C program.
- 4. Open the detergent drawer.
- 5. Pour approx. 1 litre of water into the manual dosing compartment.
- 6. Pour all-purpose detergent into the manual dosing compartment.
- Note:
- Transportation
- 1. Turn off the tap.
- 2. Release the water pressure in the supply hose: ~ "Filter in the water supply blocked" on page 40
- 3. Disconnect the washing machine from the mains power supply.
- 4. Drain the remaining water: ~ "The drain pump is blocked, emergency draining" on page 38
- 5. Detach the hoses.
- 6. Empty the dispensers. ~ Page 34
- Caution!
- Risk of damage to the appliance caused by detergent/fabric softener leaking from the dispensers
- Notes
- * Familiarising yourself with your appliance
- Familiarising yourself with your appliance
- Washing machine
- Control panel
- Select additional programme settings: ~ Page 26
- A button for:
- Display panel
- Z Laundry
- C Detergent
- 0 Programme default settings
- \ Additional programme settings
- Additional programme settings
- Water&Rinse Plus
- Easy-Iron
- Prewash
- Soaking
- Notes
- 1. Select i-DOS or pour the detergent into the manual dosing compartment in accordance with the manufacturer's instructions.
- 2. Select the Cottons//Cotton 30 °C program and press the A button.
- 3. Press the A button after approx. 10 minutes.The laundry will soak in the water.
- 4. Leave the laundry to soak for as long as required, then either press the A button again to resume the program or change the program.
- Note:
- Notes
- Speed//SpeedPerfect
- i-DOS
- 1 Operating the appliance
- Operating the appliance
- Preparing the washing machine
- Select programme/switch on the appliance
- Change the programme default settings
- Select additional programme settings
- Placing laundry into the drum
- Measure and add detergent and care products
- Start the programme
- Child lock//Child Lock
- Adding laundry
- Changing the programme
- Cancel the programme
- Programme end during rinse hold
- Programme end
- Removing laundry/switching off the appliance
- a Intelligent dosing system
- Intelligent dosing system
- Familiarising yourself with i- DOS
- i-DOS Detergent drawer
- Before setting up i-DOS
- Automatic dosing
- i-DOS Setting the dosage
- Check whether the preset basic dosages follow the manufacturer's recommendations in terms of:
- Below is an example of detergent dosages on a packaging label:
- For standard load 4 - 5 kg
- Level of soiling
- light
- normal
- heavy
- Adjusting the basic dosage
- 1. Press and hold i-DOS Ž for approx. three seconds.
- 2. Change the setting using: Spin speed/Ready in-time
- 3. Briefly press i-DOS Ž.
- 4. Change the setting using: Spin speed/Ready in-time
- 5. Press and hold i-DOS Ž for approx. three seconds, briefly press any other selectable button or wait approx. 10 seconds to exit setting mode.
- Notes
- Filling the dispensers
- Manual dosing
- Emptying the i-DOS detergent drawer, cleaning the i-DOS detergent drawer and its housing, cleaning the i-DOS pump unit
- H Sensors
- Q Appliance settings
- 2 Cleaning and maintenance
- Cleaning and maintenance
- : Warning
- Danger of death!
- : Warning
- Risk of poisoning!
- Caution!
- Damage to the appliance
- Notes
- Machine housing/control panel
- Drum
- Descaling
- The drain pump is blocked, emergency draining
- : Warning
- Risk of scalding!
- 1. Turn off the tap so that no more water can flow in and it has to be drained via the drain pump.
- 2. Switch off the appliance.Pull out the mains plug.
- 3. Open and remove the service flap.
- 4. Take the drain hose out of the holder.
- 5. Carefully unscrew the pump cover, as residual water may leak out.
- 6. Reinsert the bottom of the service flap into the slot, clip it into place and close the flap.
- Note:
- The drain hose at the siphon is blocked
- Filter in the water supply blocked
- 3 Faults and what to do about them.
- Information on the display panel
- Faults and what to do about them.
- Faults
- Cause/Remedy
- Note:
- 4 After-sales service
- J Technical data
- r Aqua-Stop warranty
- Aqua-Stop warranty
- 1. If water damage is caused due to a fault in our Aqua-Stop system, we will compensate domestic customers for the damage caused.
- 2. The liability guarantee is valid for the service life of the appliance.
- 3. It is a prerequisite of all warranty claims that the appliance with Aqua- Stop must have been installed and connected correctly in accordance with our instructions; this also includes a correctly fitted Aqua-Stop extension (genuine accessories).
- 4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured afterwards by turning off the tap.
- *9001380366*
- Thank you for buying a Bosch Home Appliance!
- Looking for help? You´ll find it here.
- Aqua-Stop warranty
en Positioning and connecting
16
appliance (not necessary for Aqua-Stop
models as this is permanently installed):
■ Model: Standard
■ Model: Aqua-Secure
■ Model: Aqua-Stop
Note: Turn on the tap carefully,
checking the leak tightness of the
connection points. The screw
connection is under mains water
pressure.
Water outlet
Caution!
Water damage
If the drain hose slips out of the wash
basin or the connection point during
draining due to high water pressure, any
escaping water may cause water
damage.
Secure the drain hose so that it cannot
slip out.
Note: Do not kink the water drain hose
or put strain on it lengthways.
You can lay the water drain hose as
follows:
■ Outlet in a sink
:Warning
Risk of scalding!
When you are washing at high
temperatures, there is a risk of
scalding if you come into contact
with hot detergent solution e.g. if hot
detergent solution is being drained
into a wash basin.
Do not reach into the hot detergent
solution.
Caution!
Damage to the appliance/fabrics
If the end of the drain hose is
immersed in the drained water, water
may be sucked back into the
appliance and may damage the
appliance/fabrics.
Make sure that:
– The plug does not block drainage
from the sink.
– The end of the drain hose is not
immersed in the drained water.
– The water drains away quickly
enough.
■ Drainage into a siphon
The connection point must be
secured using a hose clamp with a
diameter of 24-40 mm (available
from specialist dealers).