Use and Care Manual
Table Of Contents
- en Instruction Manual and Installation Instructions
- Contentsen Instruction Manual and Installation Instructions
- 8 Intended use 4
- ( Safety instructions 5
- 7 Environmental protection 11
- 5 Positioning and connecting 12
- * Familiarising yourself with your appliance 19
- Z Laundry 22
- C Detergent 23
- 0 Programme default settings 24
- \ Additional programme settings 26
- 1 Operating the appliance 27
- a Intelligent dosing system 31
- H Sensors 36
- Q Appliance settings 37
- 2 Cleaning and maintenance 38
- 3 Faults and what to do about them. 40
- 4 After-sales service 45
- J Technical data 45
- r Aqua-Stop warranty 46
- 8 Intended use
- Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Caution!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Positioning and connecting
- Positioning and connecting
- Included with the appliance
- Safety instructions
- Installation surface
- Installation on a base or a wooden joist floor
- Installation on a platform with drawer
- Installing the appliance in a kitchenette
- Removing the transport locks
- Hose and cable lengths
- Water inlet
- Water outlet
- Levelling
- Electrical connection
- Before washing for the first time
- Notes
- Preparatory work:
- Run the program without laundry:
- 1. Switch on the appliance.
- 2. Close the door (do not load any laundry).
- 3. Depending on the model, set the Drum Clean 90 °C or Cottons//Cotton 90 °C program.
- 4. Open the detergent drawer.
- 5. Pour approx. 1 litre of water into the manual dosing compartment.
- 6. Pour all-purpose detergent into the manual dosing compartment.
- Note:
- Transportation
- 1. Turn off the tap.
- 2. Release the water pressure in the supply hose: ~ "Filter in the water supply blocked" on page 40
- 3. Disconnect the washing machine from the mains power supply.
- 4. Drain the remaining water: ~ "The drain pump is blocked, emergency draining" on page 38
- 5. Detach the hoses.
- 6. Empty the dispensers. ~ Page 34
- Caution!
- Risk of damage to the appliance caused by detergent/fabric softener leaking from the dispensers
- Notes
- * Familiarising yourself with your appliance
- Familiarising yourself with your appliance
- Washing machine
- Control panel
- Select additional programme settings: ~ Page 26
- A button for:
- Display panel
- Z Laundry
- C Detergent
- 0 Programme default settings
- \ Additional programme settings
- Additional programme settings
- Water&Rinse Plus
- Easy-Iron
- Prewash
- Soaking
- Notes
- 1. Select i-DOS or pour the detergent into the manual dosing compartment in accordance with the manufacturer's instructions.
- 2. Select the Cottons//Cotton 30 °C program and press the A button.
- 3. Press the A button after approx. 10 minutes.The laundry will soak in the water.
- 4. Leave the laundry to soak for as long as required, then either press the A button again to resume the program or change the program.
- Note:
- Notes
- Speed//SpeedPerfect
- i-DOS
- 1 Operating the appliance
- Operating the appliance
- Preparing the washing machine
- Select programme/switch on the appliance
- Change the programme default settings
- Select additional programme settings
- Placing laundry into the drum
- Measure and add detergent and care products
- Start the programme
- Child lock//Child Lock
- Adding laundry
- Changing the programme
- Cancel the programme
- Programme end during rinse hold
- Programme end
- Removing laundry/switching off the appliance
- a Intelligent dosing system
- Intelligent dosing system
- Familiarising yourself with i- DOS
- i-DOS Detergent drawer
- Before setting up i-DOS
- Automatic dosing
- i-DOS Setting the dosage
- Check whether the preset basic dosages follow the manufacturer's recommendations in terms of:
- Below is an example of detergent dosages on a packaging label:
- For standard load 4 - 5 kg
- Level of soiling
- light
- normal
- heavy
- Adjusting the basic dosage
- 1. Press and hold i-DOS Ž for approx. three seconds.
- 2. Change the setting using: Spin speed/Ready in-time
- 3. Briefly press i-DOS Ž.
- 4. Change the setting using: Spin speed/Ready in-time
- 5. Press and hold i-DOS Ž for approx. three seconds, briefly press any other selectable button or wait approx. 10 seconds to exit setting mode.
- Notes
- Filling the dispensers
- Manual dosing
- Emptying the i-DOS detergent drawer, cleaning the i-DOS detergent drawer and its housing, cleaning the i-DOS pump unit
- H Sensors
- Q Appliance settings
- 2 Cleaning and maintenance
- Cleaning and maintenance
- : Warning
- Danger of death!
- : Warning
- Risk of poisoning!
- Caution!
- Damage to the appliance
- Notes
- Machine housing/control panel
- Drum
- Descaling
- The drain pump is blocked, emergency draining
- : Warning
- Risk of scalding!
- 1. Turn off the tap so that no more water can flow in and it has to be drained via the drain pump.
- 2. Switch off the appliance.Pull out the mains plug.
- 3. Open and remove the service flap.
- 4. Take the drain hose out of the holder.
- 5. Carefully unscrew the pump cover, as residual water may leak out.
- 6. Reinsert the bottom of the service flap into the slot, clip it into place and close the flap.
- Note:
- The drain hose at the siphon is blocked
- Filter in the water supply blocked
- 3 Faults and what to do about them.
- Information on the display panel
- Faults and what to do about them.
- Faults
- Cause/Remedy
- Note:
- 4 After-sales service
- J Technical data
- r Aqua-Stop warranty
- Aqua-Stop warranty
- 1. If water damage is caused due to a fault in our Aqua-Stop system, we will compensate domestic customers for the damage caused.
- 2. The liability guarantee is valid for the service life of the appliance.
- 3. It is a prerequisite of all warranty claims that the appliance with Aqua- Stop must have been installed and connected correctly in accordance with our instructions; this also includes a correctly fitted Aqua-Stop extension (genuine accessories).
- 4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured afterwards by turning off the tap.
- *9001380366*
- Thank you for buying a Bosch Home Appliance!
- Looking for help? You´ll find it here.
- Aqua-Stop warranty
Intelligent dosing system en
31
a Intelligent dosing
system
Intelligent dosing system
Familiarising yourself with i-
DOS
i-DOS Intelligent dosing system
Your appliance has an intelligent dosing
system for liquid detergent and fabric
softener.
The optimum quantities of liquid
detergent and fabric softener are
dispensed automatically depending on
the programme and settings.
Automatic dosing is activated at the
factory for all the designated
programmes and it can be adjusted to
suit your requirements. The settings are
saved when the appliance is switched
off.
For programmes in which automatic
dosing is not possible, you can add
suitable detergent to the compartment
in the detergent drawer for manual
dosing.
i-DOS Detergent drawer
Before setting up i-DOS
Follow the manufacturer's instructions
when choosing your detergent and care
product. We recommend using easy-
pour, all-purpose, universal and colour
liquid detergents for all machine-
washable, coloured items made of
cotton or synthetic fabrics.
Notes
■ Only use easy-pour liquid products
that the manufacturer recommends
adding to the detergent drawer.
■ When cleaning the i-DOS detergent
drawer, empty the dispenser
completely and clean it. ~ Page 34
■ Do not mix detergent and fabric
softener.
■ Do not use products containing
solvents, caustic agents or volatile
substances (e.g. bleach).
■ Do not use products that have
expired or are highly congealed.
Automatic dosing
The automatic dosage operates as
follows:
1. Switch on the appliance.
A function test of the i-DOS pump
unit takes place, and this can be
detected by a brief noise in the i-
DOS detergent drawer.
2. Select a programme with i-DOS
settings.
When the i-DOS setting for detergent
and fabric softener is active, the
corresponding symbols light up in
the display.
3. Start the programme.
The drum rotates and, depending on
the programme selected, load
detection takes place (takes up to 2
minutes). Depending on the load
detected, the required quantities of
detergent and fabric softener (in the
last wash cycle) are then dosed,
which can be detected by a pump
noise.
Automatic dosing can be activated or
deactivated for each of the designated
wash programmes separately.
( w dispenser for liquid detergent
0 M dispenser for fabric softener
8 Manual dosing compartment