User's Manual
Table Of Contents
- Your new washing machine
- Contentsen Instruction Manual and Installation Instructions
- 8 Intended use 4
- ( Safety instructions 5
- 7 Environmental protection 7
- Y Main points in brief 8
- * Getting to know the appliance 9
- Z Laundry 12
- C Detergent 13
- / Overview of programmes 14
- 0 Programme default settings 18
- \ Additional programme settings 19
- 1 Operating the appliance 19
- Q Appliance settings 24
- H Sensors 25
- 2 Cleaning and maintenance 26
- 3 Faults and what to do about them. 29
- 4 After-sales service 33
- [ Consumption rates 34
- J Technical data 34
- 5 Positioning and connecting 35
- r Aqua-Stop warranty 43
- 8 Intended use
- Y Main points in brief
- * Getting to know the appliance
- / Overview of programmes
- Overview of programmes
- Programmes on the programme selector
- Programme/type of laundry/information
- Settings
- Notes
- Note:
- Notes
- Note:
- Note:
- Notes
- Notes
- Notes
- Note:
- Notes
- Starching
- Dyeing/bleaching
- Soaking
- 1. Switch on the appliance.
- 2. Select the Cottons 30 °C programme.
- 3. Pour soaking agent/detergent into compartment II in accordance with the manufacturer’s instructions.
- 4. Press the A button. The programme starts.
- 5. After approx. 10 minutes, press the A button to pause the programme.
- 6. Leave the laundry to soak for as long as required, then either press the A button again to continue the programme or change the programme.
- Notes
- 0 Programme default settings
- \ Additional programme settings
- 1 Operating the appliance
- Operating the appliance
- Preparing the washing machine
- Switching on the appliance/ selecting a programme
- Placing laundry into the drum
- Measure and add detergent and care products
- Change the programme default settings
- Select additional programme settings
- Start the programme
- Child lock 3 sec.
- Adding laundry
- Changing the programme
- Cancel the programme
- Programme end during rinse hold
- Programme end
- Removing laundry/switching off the appliance
- Q Appliance settings
- H Sensors
- 2 Cleaning and maintenance
- Cleaning and maintenance
- : Warning
- Danger of death!
- : Warning
- Risk of poisoning!
- Caution!
- Damage to the appliance
- Notes
- Machine housing/control panel
- Drum
- Descaling
- Detergent drawer and housing
- 1. Pull out the detergent drawer. Press down the insert and fully remove the drawer.
- 2. To remove the insert: Push the insert upwards from below with your finger.
- 3. Clean the detergent dispenser tray and insert with water and a brush, and dry it. Clean the inside of the housing as well.
- 4. Fit the insert and lock it in place (push the cylinder onto the guide pin).
- 5. Push in the detergent drawer.
- Note:
- The drain pump is blocked, emergency draining
- : Warning
- Risk of scalding!
- 1. Turn off the tap so that no more water can flow in and has to be drained via the drain pump.
- 2. Switch off the appliance. Pull out the mains plug.
- 3. Open and remove the service flap.
- 4. Take the drain hose out of the retainer.
- 5. Carefully unscrew the pump cover; residual water may leak out.
- 6. Place the service flap back on, lock it into place, and close it.
- Note:
- The drain hose at the siphon is blocked
- Filter in the water supply blocked
- 3 Faults and what to do about them.
- Information on the display panel
- Faults and what to do about them.
- [ Consumption rates
- Consumption rates
- Energy and water consumption, programme duration and residual moisture for the main washing programmes
- Programme
- Additional function
- Load
- Energy consumption**
- Water consumption**
- Programme duration**
- J Technical data
- 5 Positioning and connecting
- Positioning and connecting
- Included with the appliance
- Safety instructions
- Installation surface
- Installation on a base or a wooden joist floor
- Installation on a platform with drawer
- Installing the appliance in a kitchenette
- Removing the transport locks
- Hose and cable lengths
- Water inlet
- Water outlet
- Levelling
- 1. Loosen the lock nuts using a WAF17 spanner, by turning it in a clockwise direction.
- 2. Check the alignment of the washing machine with a spirit level, and adjust it if necessary. Change the height by turning the appliance feet.
- 3. The lock nuts on all four appliance feet must be screwed tightly against the housing using a suitable WAF17 spanner. In doing so, hold the foot tight and do not adjust its height.
- Electrical connection
- Before washing for the first time
- Notes
- Preparatory work:
- Run the programme without laundry:
- Transportation
- Preparatory work:
- 1. Turn off the tap.
- 2. Reduce the water pressure in the supply hose: ~ Page 28; Cleaning and maintenance – filter in the water supply blocked
- 3. Disconnect the washing machine from the mains.
- 4. Drain the remaining water: ~ Page 27; cleaning and maintenance – the drain pump is blocked, emergency draining
- 5. Remove the hoses.
- Installing the transport braces:
- Notes
- Preparatory work:
- r Aqua-Stop warranty
- Aqua-Stop warranty
- 1. If water damage is caused due to a fault in our Aqua-Stop system, we will compensate domestic customers for the damage caused.
- 2. The liability guarantee is valid for the service life of the appliance.
- 3. It is a prerequisite of all warranty claims that the appliance with Aqua-Stop must have been installed and connected correctly in accordance with our instructions; this also includes a correctly fitted Aqua-Stop extension (genuine accessories).
- 4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured afterwards by turning off the tap.
- Aqua-Stop warranty
Positioning and connecting en
35
5 Positioning and
connecting
Positioning and connecting
Included with the appliance
Note: Check the machine for transport
damage. Never use a damaged
machine. If you have any complaints,
contact the dealer from whom you
purchased the appliance or our
customer services. ~ Page 33
( Mains cable
0 Bag:
■ Installation and operating
instructions
■ Customer services location
directory*
■ Warranty*
■ Cover caps for openings after
the transport braces have
been removed
■ Adaptor with sealing washer
from 21 mm = ½" to
26.4 mm = ¾" *
8 Water supply hose on Aqua-Stop
models
@ Water drain hose
H Elbow for securing the water
drain hose*
P Water supply hose on standard/
Aqua-Secure models
* depending on the model
3
+
#