Installation Instruction
Table Of Contents
- en Instruction Manual and Installation Instructions
- Display rules
- : Warning!
- Caution!
- Note/tip
- 1. 2. 3. / a) b) c)
- Contentsen Instruction Manual and Installation Instructions
- 8 Intended use 4
- ( Safety instructions 5
- 7 Environmental protection 12
- 5 Positioning and connecting 13
- * Getting to know the appliance 22
- Z Laundry 25
- P Overview of programmes 27
- 0 Programme default settings 32
- \ Additional programme settings 33
- 1 Operating the appliance 35
- Q Appliance settings 39
- H Sensors 41
- 2 Cleaning and maintenance 41
- 3 Faults and what to do about them 45
- 4 After-sales service 51
- [ Consumption values 52
- J Technical data 53
- r Aqua-Stop warranty 53
- 8 Intended use
- Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Caution!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Positioning and connecting
- – WAF13 for loosening the transport braces and
- – WAF17 for aligning the appliance feet
- 2. Unscrew and remove all four transport brace screws.
- 3. Fit the covers.
- 4. Lock the covers firmly in place by applying pressure to the snap-in hooks.
- 2. Remove the transport struts.
- 3. Undo and remove the screws on the horizontal transport strut.
- 4. Remove the transport strut.
- 2. Open the water tap carefully, checking the leak tightness of the connection points. The screw connection is under mains water pressure.
- 2. Check the alignment of the appliance with a spirit level, and adjust it if necessary. Change the height by turning the appliance feet.
- 3. Tighten the lock nut against the housing.
- 2. Turn the water tap on.
- 3. Press the # button till the indicator lamp lights up, release the button. The appliance is switched on.
- 4. Close the door. Do not load any laundry.
- 5. Select the Καθαρισμός κάδου (Drum Clean) 90°C programme.
- 6. Open the detergent drawer.
- 7. Pour approx. 1 litre of water into dispenser II.
- 8. Add standard detergent to dispenser II according to manufacturer’s instructions for light soiling.
- 9. Close the detergent drawer.
- 10. Select A.
- 11. When the programme ends, press the # button till the indicator lamp turns off, release the button.
- 2. Reduce the water pressure in the supply hose. ~ Page 44
- 3. Drain any residual water. ~ Page 42
- 4. Disconnect the appliance from the mains.
- 5. Remove the hoses.
- 6. Empty the dispensers. ~ "Detergent drawer and housing" on page 41
- 2. Insert all four sleeves.
- * Getting to know the appliance
- Getting to know the appliance
- Appliance
- Control panel
- Touch-Display
- Programme default settings
- Additional programme settings
- Status indicators for the programme progress (programme sequence)
- Protecting your laundry and appliance
- Sorting laundry
- Note:
- – Light: Do not need to pretreat, adjust the Speed setting if necessary.
- – Normal
- – Heavy: Load less laundry, need to pretreat or soak laundry firstly.
- – Stains: Remove/pretreat stains while they are fresh. First dab with soapy water; do not rub. Then wash the items of laundry with the appropriate programme. Stubborn or dried-in stains can sometimes only be removed by washing several times.
- 2. Select the Ξέβγαλμα (Rinse) programme.
- 3. Measure starch into compartment © in accordance with the manufacturer's instructions (clean first if necessary).
- 4. Touch the A button.
- 2. Select the ˜ button repeatedly until the required number of hours is displayed.
- 3. Select the A button.
- 2. Touch the ˜ or ~ button to change the number of hours.
- 3. Select the A button.
- 2. Select a programme.
- 3. If required, change the programme default settings and/or select programme additional settings.
- 4. Touch and hold â (Memory) button for approx. three seconds.
- 2. Turn the water tap on.
- 3. Open the appliance door.
- 2. Pour in detergent and/or cleaning product.
- 2. Slide the measuring aid forwards, fold it down and click it into place.
- 3. Reinsert the drawer.
- 2. Select another programme.
- 3. And touch the A button again. The new programme starts from the beginning.
- 2. To cool down laundry: Select Ξέβγαλμα (Rinse).
- 3. Touch the A button.
- 2. Select Στύψιμο (Spin).
- 3. Touch the A button.
- 2. Switch the appliance on again.
- 3. To cool down laundry: Select the MyTime + Dry.
- 4. Touch the A button.
- 2. Open the door and remove the laundry.
- 3. Turn off the water tap.
- End signal
- Button signal
- Brightness
- Switching the drum-care information signal on/off
- Possible setting values:
- H Sensors
- 2 Cleaning and maintenance
- If the appliance contains detergent or fabric softener residues:
- 2. To remove the insert: Push the insert upwards from below with your finger.
- 3. Clean the detergent dispenser tray and insert with water and a brush, and dry it. Clean the inside of the housing as well.
- 4. Fit the insert and lock it in place (push the cylinder onto the guide pin).
- 5. Push in the detergent drawer.
- 2. Open the service flap.
- 3. Take the drain hose out of the retainer.
- 4. Carefully unscrew the pump cover; residual water may leak out.
- 5. Refit and screw on the pump cover. The handle must be in a vertical position.
- 6. Close the service flap.
- 2. Loosen the hose clamp. Carefully remove the drain hose; residual water may leak out.
- 3. Clean the drain hose and siphon connecting piece.
- 4. Re-attach the drain hose and secure the connection point using the hose clamp.
- 2. Select the Βαμβακερά (Cottons) (activate Speed setting) programme.
- 3. Select the A button. Allow the programme to run for approx. 40 seconds.
- 4. Press the button #.
- 5. Pull out the mains plug.
- 2. Use pliers to remove the filter.
- 3. Clean the filter with a small brush.
- 4. Connect the hose and check for leaks.
- 2. Open the service flap.
- 3. Drain the water. ~ Page 42
- 4. Pull the emergency release downwards with a tool and release.
- Information on the display panel
- Faults and what to do about them
- Energy and water consumption, programme duration and residual moisture for the main washing programme (approximate values)
- In addition to warranty claims against the vendor based on the purchase agreement and to our appliance warranty, we will provide compensation under the following conditions:
- 2. The liability guarantee is valid for the service life of the appliance.
- 3. It is a prerequisite of all warranty claims that the appliance with Aqua- Stop must have been installed and connected correctly in accordance with our instructions; this also includes a correctly fitted Aqua-Stop extension (genuine accessories).
- 4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured afterwards by turning off the tap.
en Appliance settings
40
End signal
You can select position 1 and use the
˜ button to adjust the volume of the
end signal, e.g. ‘- „.
Possible setting values:
Button signal
You can select position 2 and use the
˜ button to adjust the volume of the
button signal, e.g. ›- „.
Possible setting values:
Brightness
Possible setting values: 1 - 4
You can select position 3 and use the
˜ button to adjust the brightness of the
Touch-Display, e.g. ’- „.
Possible setting values:
Switching the drum-care information
signal on/off
You can select position 4 and use the
˜ button to switch the Καθαρισμός
κάδου (Drum Clean) information signal
on or off, e.g. š- ‚.
Possible setting values:
0 off
1 quiet
2 medium
3 loud
4 very loud
0 off
1 quiet
2 medium
3 loud
4 very loud
1 not very bright
2 normal level of
brightness
3 bright
4 very bright
0 off
1on