Washing machine WLT...
Your new washing machine Display rules You have chosen a Bosch washing machine. : Warning! Please take a few minutes to read and become familiar with the advantages of your washing machine. This combination of symbol and signal word indicates a possibly dangerous situation. Not heeding the warning can cause death or injuries.
en Contents enI structionManual ndInstal tionI structions 8 Intended use. . . . . . . . . . . . . . . . .4 ( Safety instructions . . . . . . . . . . .5 Electrical safety. . . . . . . . . . . . . . . . . . 5 Risk of injury . . . . . . . . . . . . . . . . . . . . 5 Safety for children. . . . . . . . . . . . . . . . 5 7 Environmental protection . . . . . .7 Packaging/used appliance . . . . . . . . . 7 Tips on economical use . . . . . . . . . . . 7 * Getting to know the appliance . 8 Washing machine . . .
en Intended use 4 After-sales service . . . . . . . . . . 26 J Technical data . . . . . . . . . . . . . . 26 5 Positioning and connecting. . . 27 Included with the appliance . . . . . . . 27 Safety instructions . . . . . . . . . . . . . . 27 Installation surface . . . . . . . . . . . . . . 28 Installation on a base or a wooden joist floor . . . . . . . . . . . . . . . . . . . . . . . . . 28 Installation on a platform with drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety instructions ( Safety instructions Electrical safety snoitcursniyteSfa : Warning Danger of death! There is a risk of electric shock if you touch live components. ■ Never touch or hold the mains plug with wet hands. ■ Only pull out the mains cable by the plug and never by the cable, as this could damage it. Risk of injury : Warning Risk of injury! If the washing machine is lifted by protruding components (e.g. the washing machine door), the components may break off and cause injuries.
en ■ Safety instructions Children may lock themselves in appliances, putting their lives at risk. When appliances have reached the end of their service life: – Unplug the mains plug. – Cut through the mains cable and remove it, along with the plug. – Destroy the lock on the washing machine door. : Warning Risk of suffocation! Children may become wrapped in packaging/film or packing parts if allowed to play with them, or they may pull them over their heads and suffocate.
Environmental protection 7 Environmental ■ protection Packaging/used appliance noitceorplamnoteriEv ) Dispose of packaging in an environmentally-responsible manner. This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.
en Getting to know the appliance * Getting to know the appliance Washing machine ecnailpehtwonk gnitGe # 6 ( 0 8 9S 9T @ 8 7 Detergent drawer Operating/display panel Loading door with door handle Open the loading door Close the loading door Service flap
Getting to know the appliance en Control panel Control panel depending on the model Note: The buttons are sensitive, they only need to be touched gently. ( Programs You can find an overview of all programs on the printed supplement for the installation and operating instructions.
en Button Getting to know the appliance Display Description Additional programme settings: ~ Page 14 @ Display Description r Tap ~ "3 Faults and what to do about them." on page 23 GF ü Speed Eco Perfect Z Water Plus Q Easy Iron* ~ Page 17 T Prewash* ~ "3 Faults and what to do about them." on page 23 Button to start, interrupt (e.g.
Laundry Z Laundry ■ Prepare the laundry yrdnuaL Caution! Damage to the appliance/fabrics Foreign objects (e.g. coins, paper-clips, needles, nails) may damage the laundry or components in the washing machine. Therefore, note the following tips when preparing your laundry: ■ Empty pockets. ■ ■ ■ ■ ■ ■ Look out for metal items (paperclips, etc.) and remove them. Wash delicates in a laundry bag (tights, underwired bras, etc.). Close any zips, button up any cover buttons.
en Detergent Dyeing/bleaching Dye should only be used in normal household quantities. Salt may damage stainless steel. Always follow the dye manufacturer's instructions. Do not use the washing machine to bleach clothes. C Detergent Correct selection of detergent tnegrD The care label is crucial for selecting the correct detergent, temperature and treatment of the laundry. ~ See also www.sartex.ch If you visit www.cleanright.
Programme default settings 0 Programme default settings The default program settings are displayed in the display panel after selecting the program. You can change the default settings. To do this, repeatedly press the corresponding button until the required setting is displayed on the display panel. sgnites luafmedrgoP Note: Pressing and holding the buttons automatically runs through the setting values until the last one.
en ■ ■ ■ Additional programme settings Imbalances (e. g. due to fitted sheets) are offset with several startups of spin cycles, Fluctuations in power supply, Water pressure (infeeding speed). achieving a washing result that is consistent with the selected program, without the Speed Eco Perfect setting. Following the start of the program , you can change the preselected number of hours as follows: 1. Press the A button. 2. Use the Finished in-time button to change the number of hours. 3.
Operating the appliance 1 Operating the appliance Preparing the washing machine ecnailpehtgniaOrep Note: The washing machine must be correctly installed and connected. ~ Page 27 1. 2. 3. 4. Plug into the mains. Turn on the tap. Open the washing machine door. Check that the drum is completely drained. Drain if necessary. Select programme/switch on the appliance Note: If you have activated the childproof lock, you must first deactivate it before you can set a program.
en Operating the appliance Notes ■ Mix items of laundry of varying sizes. Laundry items of different sizes distribute themselves better during the spin cycle. Individual laundry items may cause an unbalanced load. ■ Observe the maximum indicated load. Overfilling adversely affects the washing result and encourages creasing. 1. Unfold presorted laundry items and place them in the washing drum. 2. Make sure that no items of laundry are trapped between the door and the rubber seal, and close the door.
Operating the appliance Start the programme Press the A button. The indicator lamp lights up and the program starts. The display panel shows the Ready in time while the program is running or the program duration and the program progress symbols once the wash cycle has started.
en Operating the appliance To continue the program, press the button A.The program continues automatically. Notes ■ Do not leave the door open for too long when adding laundry as water from the laundry may leak out. ■ For safety reasons, the door remains locked when the water level or temperature is high, or while the drum is turning, and it is not possible to add laundry during this time. ■ The load display is not active during reloading. Changing the programme 1. Press the A button. 2.
Sensors en H Sensors Automatic load sensing sroSne The automatic load sensing function adapts the water consumption ideally to each programme depending on the type of fabric and the load. Unbalanced load detection system The automatic unbalanced load detection system detects imbalances and ensures even distribution of the laundry by repeatedly starting and stopping drum spinning.
en Cleaning and maintenance The setting mode is activated and the preset volume for the information signals appears in the display panel (e.g. at the end of the program). Changing the volume Use the Finished in-time + or - button to change the following settings at the corresponding program selector positions: ■ 2: The volume of the information signals and/or ■ 3: The volume of the button signals.
Cleaning and maintenance Descaling Descaling should not be necessary if the detergent is measured out correctly. However, if it is required, follow the manufacturer's instructions for the descaling agent. Suitable descalers can be obtained via our website or from our after-sales service. en Allow the detergent solution to cool down. 1. Turn off the water tap so that no more water can flow in and has to be drained via the drain pump. 2. Switch off the appliance. Pull out the mains plug. 3.
en Cleaning and maintenance 6. Put the service flap back on, engage and close it. Note: To prevent unused detergent from flowing into the outlet during the next wash: Pour 1 litre of water into compartment II and start the0 Spin/[ Drain/Empty programme (if only a drain cycle is required, set rpm (spin speed) to - 0 -). The drain hose at the siphon is blocked 1. Switch off the appliance. Disconnect the mains plug. 2. Loosen the hose clamp. Carefully remove the drain hose, residual water may leak out. 3.
Faults and what to do about them. 3 Faults and what to do about them. Emergency release meh.t uobadt wahdnstluFa e.g. in the event of a power cut The programme will continue running when the power supply has been restored. However, if the laundry has to be removed, the washing machine door can be opened as follows: : Warning Risk of scalding! When you are washing at high temperatures, there is a risk of scalding if you come into contact with detergent solution and laundry.
en Faults and what to do about them. Display Cause/remedy E:18 ■ ■ The drain pump is blocked. Clean the drain pump. ~ Page 21 The drain hose/drain pipe is blocked. Clean the drain hose at the siphon. ~ Page 22 E:23 There is water in the base plate, the appliance is leaking. Turn off the tap. Call the after-sales service! ~ Page 26 E The childproof lock is activated – deactivate it. Å lights up Too much foam has been detected and an additional wash cycle has been activated.
Faults and what to do about them. Faults The spin result is not satisfactory. Laundry is wet/too damp. Cause/Remedy ■ ■ ■ The spin cycle runs several times. The program is taking longer than usual. en Not a fault – the unbalanced load detection system has interrupted the spin cycle because the laundry is unevenly distributed. Distribute small and large items of laundry evenly in the drum.
en After-sales service Faults Cause/Remedy In the pause mode, the è symbol in the display is off. The door is unlocked. It is possible to add laundry. If you cannot rectify a fault yourself (after switching the machine off and on again) or a repair is required: ■ Switch off the appliance and pull out the mains plug. ■ Turn off the tap and call customer services. 4 After-sales service If you cannot rectify a fault yourself, contact customer services.
Positioning and connecting 5 Positioning and connecting Included with the appliance gnitceodnagiotPso Note: Check the machine for transport damage. Never use a damaged machine. If you have any complaints, contact the dealer from whom you purchased the appliance or our Customer Service.
en Positioning and connecting Caution! Water damage The connection points for the water supply hose and water drain hose are under high water pressure. To prevent leaks and water damage, you must follow the instructions in this section. Notes ■ In addition to the safety information listed here, the local water and electricity supplier may have special requirements. ■ If in doubt, have the appliance connected by a specialist.
Positioning and connecting Note: Keep the screws and sleeves in a safe place. en Hose and cable lengths ■ Left-hand connection a FP PD[ FP a FP ■ a FP Right-hand connection 2. Unscrew and remove all four transport brace screws. Remove the sleeves. To do this, remove the mains cable from the holders. a FP a FP 3. Fit the covers. Lock the covers firmly in place by applying pressure to the snap-in hooks. a FP PD[ FP 1. Take the hoses out of the holders.
en ■ Positioning and connecting Only tighten the screw connections by hand. If the screw connections are tightened too much with a tool (pliers), the thread may become damaged. Optimum water pressure in the mains: 100-1000 kPa (1-10 bar) ■ When the tap is open, the water flow is at least 8 l/min. ■ If the water pressure is higher than this, a pressure-reducing valve must be installed. Connection Connect the water supply hose to the water tap (¾" = 26.
Positioning and connecting Make sure that: – The plug does not block drainage from the sink. – The end of the drain hose is not immersed in the drained water. – The water drains away quickly enough. ■ en 2. Check the alignment of the washing machine with a spirit level, and adjust it if necessary. Change the height by turning the appliance feet. All four appliance feet must stand firmly on the ground. 3. Tighten the lock nut against the housing.
en ■ ■ ■ ■ ■ ■ ■ ■ Positioning and connecting The mains plug fits the socket. The cable cross-section is adequate. The earthing system is properly installed. The mains cable is only replaced by a qualified electrician (if this is necessary). Replacement mains cables are available from the aftersales service. No multiple plugs/couplings or extension cables are used. If an earth-leakage circuit breaker is used, only a type which displays this symbol is used: z.
Aqua-Stop warranty 2. Insert all four sleeves. Clip the mains cable securely in the holders. Insert and tighten the screws. Before switching on the appliance again: Notes The transport braces must be removed. ■ To prevent unused detergent from flowing into the outlet during the next wash: Pour approx. 1 litre of water into compartment II and start the 0 Spin/[ Drain/Empty programme (if only a drain cycle is required, set rpm (spin speed) to - 0 -).
6
6
7 Advice and repair order in the event of faults GB IE 0344 892 8979 (Calls charged at local or mobile rate.) 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.) You can find the contact information for all countries in the attached after-sales service directory.
