Installation Instructions
Table Of Contents
- en-us Use and Care Manual, Installation Instructions
- Table of contentsen-us Use and Care Manual, Installation Instructions
- Important information
- Your dryer is intended for
- Safety Definitions
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- Introduction to your new dryer
- Dimensions and clearances required
- Installation Instructions
- Introduction
- Before installing the dryer
- Waste disposal
- Parts provided with your dryer
- Accessories for your appliance
- Installation - step by step
- 1. Unpack the dryer.
- 1. Fasten the dryer drain hose to the washer drain/elbow as shown in picture “A”. Secure with plastic ties supplied.
- Electrical Connections
- NOTICE:
- 1. Unplug the current power cord being used from the outlet/receptacle.
- 2. To disconnect and/or reconnect a new power cord you must remove the top cover of the appliance as shown below.
- 3. Open the connection box toward the rear of the appliance by removing the T20 torx head screw fastening the cover.
- 4. Remove the 4-wire power cord (as supplied):
- NOTICE:
- NOTICE:
- NOTICE:
- 9. Ensure the terminal ends are long enough and are formed (bent) so they will align with the terminal block fastening locations (screw holes).
- 10. Reinstall the 2 terminal block screws (Philips head) at locations L as shown below.
- 11. If the ground wire shown below from N to PE is not part of the 3-wire cord assembly you have it must be obtained/purchased separately and it must be installed.
- 12. Install the last terminal block screw (Philips) and 1 grounding screw (T20 torx) at locations N and PE.
- 13. Tighten the strain relief screw ensuring the power cord cannot be pulled out of the connection box but not so tight as cut the power cord insulation.
- 14. Reinstall the connection box cover making sure all wires are routed so they do not touch any part of the enclosure and are secure.
- 15. Reinstall the appliance top cover as previously described in “2” above.
- 9 CAUTION
- 9 CAUTION
- Leveling the dryer
- 1. Install the dryer on a level and solid surface, preferably in a corner of a room.
- 2. If the floor is uneven (or not level) adjust the dryer feet as required to level the dryer. Do not place anything under the dryer feet to help level the dryer.
- 3. Extend the dryer feet no more than is necessary. The more the feet are extended, the more vibration the dryer will experience. Start with the dryer feet turned all the way in and adjust each foot as necessary.
- 4. Use a bubble level to check the top of the dryer to make sure it is level side to side and front to rear.
- 5. Press down on each corner of the dryer top to make sure the dryer does not “wobble“. There should be no "give" or movement. All four dryer feet should press equally against the floor. This is just as important as the dryer being level to preve...
- 1. Install the dryer on a level and solid surface, preferably in a corner of a room.
- Check heating system
- Preparing to transport the dryer - step by step
- Getting to know your appliance
- Operating Instructions
- 9 WARNING
- Your new dryer
- 9 WARNING
- Before using the dryer for the first time
- 1. Read these operating instructions carefully.
- 2. Check that the supply voltage corresponds with the voltage specifications on the rating plate on the dryer, see top rear side of the dryer and/or rating plate label inside of the dryer door. ~ Electrical Connections; Page 14
- 3. Remove all objects from the drum.
- 4. Check the dryer for visible damage. If damage found contact your dealer.
- 5. Wipe the inside of the drum with a damp cloth.
- 6. Check heating system. ~ Check heating system; Page 17
- 7. If the dryer does not work, switch the dryer to Off. Look in the Troubleshooting section of the operating instructions for support. ~ Troubleshooting; Page 32
- 1. Read these operating instructions carefully.
- Temporary disconnection of the dryer
- Using the program selector to choose a drying cycle
- Program selection
- Selecting program settings and additional options
- Loading the laundry
- Starting the program
- Indicator of program sequence
- Childproof lock
- Selecting a different program
- Cancel program
- Program end
- Removing laundry/switching the appliance off
- Signal
- Laundry
- Program selection table
- Default Program and Option settings
- Additional Program Option settings
- Spin speed
- Cleaning and maintenance
- 9 WARNING
- 9 CAUTION
- Cleaning the housing and control panel
- Cleaning the lint filter area
- Cleaning the lint filter
- Cleaning the heat exchanger
- 1. If the dryer is hot, run on Air Fluff/No Heat program to allow the dryer to cool down.
- 2. Residual water may escape, place an absorbent cloth under the maintenance flap.
- 3. Unlock the maintenance flap and open it completely.
- 4. Turn both locking levers towards each other.
- 5. Pull out the heat exchanger cap.
- 6. Remove the heat exchanger.
- NOTICE:
- 7. Rinse the heat exchanger and the cap on all sides with a jet of water to completely remove all of the lint and fluff.
- 8. Remove all lint and fluff from the seals on the dryer and heat exchanger.
- 9. Allow the cap and the heat exchanger to dry fully.
- 10. First insert the heat exchanger, then the cap.
- 11. Turn back both locking levers.
- 12. Close the maintenance flap until it locks into position.
- 13. Look in the Troubleshooting table to reset the maintenance indication. ~ Troubleshooting; Page 32
- 1. If the dryer is hot, run on Air Fluff/No Heat program to allow the dryer to cool down.
- Cleaning the moisture sensors
- Maintenance of drain hose
- Troubleshooting
- STATEMENT OF LIMITED PRODUCT WARRANTY
27
Default Program and Option settings
At the factory initial settings are pre-set for all cycles.
You can change some program settings as follows.
Dry Level
This option adjusts the drying time in small steps for
certain programs.
Default setting = OFF (no LED Symbol shown)
Selectable values: OFF, +1, +2, +3
The Dry Level is retained until changed.
NOTICE: The higher the number value the increased
time of drying.
Time dry
Available only for Time programs,
~ Program selection table; Page 26
can be selected from minimum 20 minutes to maximum
3 hours, in 10-minute steps.
Finish in
The program end (Finish in) time can be set in one hour
increments to a maximum of 24 h (hours).
After selecting the desired drying program (at the dial)
but before touching the Start button, touch the Finish in
button until the desired time is displayed, e.g. 8 h, then
touch the Start button to start the dryer.
NOTICE: The cycle duration is included in the set Finish
in time.
Here is an example of 1hr:30min cycle time and an 8 h
Finish in time. 8 h is displayed (until Energy-saving mode
activates) and counts down (approximately 6hr:30min)
until the drying cycle begins (at 1hr:30min) then the cycle
duration 1:30 is displayed and drying begins. Total time
approximately 8 hours.
Additional Program Option settings
Wrinkle Block
If the Wrinkle Block option is activated it prevents the
laundry from creasing or wrinkling. The drum rotates at
specific intervals after the drying process allowing the
load to remain loose and fluffy until removed.
If the Wrinkle Block button is touched, this function is set
to 60 (+60m) or 90 (+90m) minutes.
The laundry remains loose and fluffy until it is removed.
The laundry should be removed before this time has
elapsed.
Low Heat
Reduced temperature for delicate fabrics, e.g.
polyacrylic, polyamide or elastane, with longer drying
time.
Observe the care information or symbols on the textile’s
label.