Integrated IR Bullet Camera WZ20 en Installation Manual
Integrated IR Bullet Camera Table of Contents | en 3 Table of Contents 1 Safety 4 1.1 Safety Precautions 4 1.2 Important Safety Instructions 4 1.3 Important Notices 6 1.4 FCC & ICES compliance 9 1.5 Warranty / Limitation of Liability 11 1.6 Contact Information 13 2 Introduction 14 2.1 Description 14 2.2 Parts List 14 3 Installation 15 4 Configuration 16 4.1 Configuration Overview 16 4.1.1 Adjusting Pan, Tilt, Rotate 17 4.1.2 Adjusting Focus 17 4.1.
en | Safety Integrated IR Bullet Camera 1 Safety 1.1 Safety Precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation.
Integrated IR Bullet Camera 2. Safety | en Keep this instruction. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean inside only with dry cloth. 7. 5 Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9.
en | Safety 1.3 Integrated IR Bullet Camera Important Notices Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury and/or serious damage to the unit. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use caution and care when moving the cart/apparatus combination to avoid injury from tip-over.
Integrated IR Bullet Camera Safety | en 7 U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides information regarding proper grounding of the mount and supporting structure, grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
en | Safety Integrated IR Bullet Camera Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible. Power resupply - If the unit is forced to power down due to exceeding the specified operating temperatures, disconnect the power cord, wait for at least 30 seconds, and then reconnect the power cord. Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights.
Integrated IR Bullet Camera 1.4 Safety | en 9 FCC & ICES compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that my cause undesired operation. FCC Information (U.S.A.
en | Safety Integrated IR Bullet Camera How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
Integrated IR Bullet Camera Safety | en 11 communications (FCC), peut s'avérer utile : How to Identify and Resolve Radio-TV Interference Problems (Comment identifier et résoudre les problèmes d’interférences de radio et de télévision). Cette brochure est disponible auprès du U.S. Government Printing Office, Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4. NOTICE! This is a Class B product.
en | Safety Integrated IR Bullet Camera The foregoing warranty is subject to Buyer’s (i) promptly written claim and (ii) timely provision to BOSCH Security Systems of an opportunity to inspect and test the Product claimed to be defective. Such inspection may be on Buyer’s premises and/or BOSCH Security Systems may request the return of the Product at Buyer’s expense.
Integrated IR Bullet Camera 1.6 Safety | en 13 Contact Information Americas Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450 USA Phone: +1 800 289 0096 Fax: +1 585 223 9180 security.sales@us.bosch.com www.boschsecurity.us Europe, Middle East, Africa Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven, The Netherlands Phone: + 31 40 2577 284 Fax: +31 40 2577 330 emea.securitysystems@bosch.com www.boschsecurity.
en | Introduction Integrated IR Bullet Camera 2 Introduction 2.1 Description The WZ20 Integrated IR Bullet camera is a night vision DSP color CCD camera with 1/3 in. LXR CCD with dual-window mechanical filter. The camera can be installed easily in most indoor locations.
Integrated IR Bullet Camera 3 Installation | en 15 Installation CAUTION! To prevent humidity problems, the camera must be installed in dry conditions. 1. Select a mounting surface that is strong enough to support the camera and that is far from electric or magnetic fields as well as high temperatures. 2. Connect the camera to either a 12VDC (recommended for best picture and the most stable camera operation) or 24 VAC regulated power supply (not included). 3.
en | Configuration Integrated IR Bullet Camera 4 Configuration 4.1 Configuration Overview The figure below displays the controls on the bottom of the camera or on the mounting bracket that are available for camera adjustment. The tables below each figure identify each control. Figure 4.1 Number 1 2 3 4 5 6 7 8 | 2.0 | 2011.
Integrated IR Bullet Camera 4.1.1 Configuration | en 17 Adjusting Pan, Tilt, Rotate 1. Locate the 3 set screws on the bracket, as identified (6, 7, 8) in the figure above. 2. Loosen the 3 set screws using the supplied hex key. 3. Adjust the pan, tilt, and rotate as necessary. NOTICE! Do not pan or rotate beyond 360˚ as shown in the figure below. Do not tilt beyond 90˚ as shown. Do not apply excessive force when adjusting the camera positioning. Figure 4.2 Camera Pan, Tilt, and Rotate 4.1.
en | Configuration 4.1.3 Adjusting Zoom 1. | 2.0 | 2011.06 Integrated IR Bullet Camera Remove the cap covering the bottom of the camera. 2. Adjust the zoom knob as necessary (see Figure 4.1 above). 3. Replace the cap over the bottom of the camera. Installation Manual Bosch Security Systems, Inc.
Integrated IR Bullet Camera On-Screen Menu | en 5 On-Screen Menu 5.1 OSD Menu Exposure Color 5.1.1 Day/Night Function Motion Privacy Set 19 Exit Exposure Submenu This menu allows you to set and adjust the lens functions. LENS E. SHUTTER BLC AGC – MANUAL/DC AUTO~1/100000 OFF~36dB MANUAL/DC: A setting for switching between manual and DC operation of the lens. – E. SHUTTER: Electronic Shutter - A function that allows you to set the shutter speed (from 1/60(50) to 1/100K).
en | On-Screen Menu 5.1.2 Integrated IR Bullet Camera Color Submenu This menu allows you to control and adjust the RGB level for the camera to represent accurate white color. WB MODE AWC ATW MANUAL PUSH LOCK – WB MODE: White Balance Mode – AWC: Auto White Balance - A function that allows a color camera to adjust its output color automatically to give a natural color independent of the lighting used.
Integrated IR Bullet Camera 5.1.3 On-Screen Menu | en 21 Day/Night Submenu This menu allows you to set the day/night mode in order to adjust the output image depending on the light levels. D&N MODE – AUTO COLOR B/W AUTO: In this mode, the camera output switches automatically between color and day/night modes, depending on light levels. – COLOR: In this mode, the camera output is only in color. – B/W: In this mode, the camera output is only in black and white. 5.1.
en | On-Screen Menu Integrated IR Bullet Camera – MIRROR: A function that enables you to set up reversed – SHARPNESS: A function that enables you to set up – GAMMA: A function that enables you to set up – SLC: Side Light Compensation - Select this mode when the LEFT and RIGHT images. sharpness control. compensation according to gamma value. corner of the screen is darker than the center. As the level increases, the image becomes brighter.
Integrated IR Bullet Camera – On-Screen Menu | en 23 SET WINDOW: With the joystick, select or deselect areas where you want to detect motion. Only areas in blue are monitored for movement; the others are ignored/masked. Figure 5.1 Set Motion Detection area – ALL SET: Set the entire screen for movement detection. – ALL CLEAR: Clear the entire screen for movement detection – SENSITI.: Sensitivity level - As the sensitivity level increases, smaller movements are detected. – SHOW INDI.
en | On-Screen Menu – Integrated IR Bullet Camera MASK 1 - MASK 4: These are the four (4) mask areas that you can set. – COLOR SET: A function that enables you to select the color of the masking cells. Figure 5.2 Privacy Mask If “SET WINDOW” is selected, the cell appears on the screen. To adjust the cell, move the joystick UP / DOWN / RIGHT / LEFT.
Integrated IR Bullet Camera – On-Screen Menu | en 25 CAMERA ID: This is where you set the ID (title) of the camera. – TITLE EDIT: This is where you select the value for the camera title. – TITLE RESET: This is where you clear the value of the camera title. – TITLE POSITION: This is where you select the area to display the title. – DPC SET: Defect Pixel Cancellation Set - This function automatically removes dead pixels in real time.
en | Troubleshooting Integrated IR Bullet Camera 6 Troubleshooting 6.1 Troubleshooting Tips Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center. - If no image appears, verify that: – The coaxial cable is attached securely. – The power and voltage are normal. – The iris of the lens inside the camera was adjusted correctly (with the level volume). – There is adequate illumination.
Integrated IR Bullet Camera 7 Technical Specifications | en 27 Technical Specifications PV72-CB93H_TM-EX-TDN5-AC8A-30IR-HEATER Part numbers: WZ20NXV550-0 (NTSC) | WZ20PXV550-0 (PAL) Electrical Power 12 VDC 10 - 16 V consumption 24 VAC 20 - 28 V with DC = Max 6.7 W LED on AC = Max 8 W (with infrared on) Video Signal Format NTSC PAL Signal processing Output signal 1V P-P composite video, 75 Ohms CCD Type 1/3 in. 410 K 1/3 in.
en | Technical Specifications Integrated IR Bullet Camera Mechanical Dimension Φ 98 mm x 202 mm (L) Weight 1.7 kg (3.8 lbs) Construction Robust aluminum extrusion Finish Anodized silver Camera Pan/Tilt Range Pan: 360° total Tilt: 90° total Environmental Rating IP66 Operating Temperature -30 °C to +55 °C (-22 °F to 131 °F) | 2.0 | 2011.06 Storage Temperature -20 °C to +70 °C (-4 °F to 158 °F) Operating Humidity under 90% (non-condensing) Installation Manual Bosch Security Systems, Inc.
Integrated IR Bullet Camera Technical Specifications | en 29 Dimensions Below are several dimensional drawings of the camera. Unit of measure is mm. Figure 7.1 Front view Figure 7.2 Top view Bosch Security Systems, Inc. Installation Manual | 2.0 | 2011.
en | Technical Specifications | 2.0 | 2011.06 Integrated IR Bullet Camera Installation Manual Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.
