Owner's Manual
Table Of Contents
- Owner’s Guide
- Important Safety Instructions
- Contents
- Introduction
- Setting Up the System
- Operation
- F1 Model 812 Control Panel
- F1 Subwoofer Control Panel
- Power On/Off Sequence
- Setting EQ selector switches
- Connecting Sources
- Connection Scenarios
- Full band, mixing console stereo output to L/R F1 Model 812 Loudspeakers
- Full band with mixing console, one F1 Subwoofer and two F1 Model 812 Loudspeakers
- Mixing console stereo output to F1 Subwoofer and left/right F1 Model 812 Loudspeakers
- Full band with mixing console stereo output to two F1 Subwoofers and two F1 Model 812 Loudspeakers
- Stereo input to Left/right F1 Subwoofers and F1 Model 812 Loudspeakers
- Mic to F1 Model 812 Loudspeaker INPUT 1
- Mobile device to single F1 Model 812 Loudspeaker
- Mobile device to F1 Flexible Array Loudspeaker system
- Mobile device to F1 Model 812 Loudspeaker and F1 Subwoofer
- DJ Console to two F1 Subwoofers and two F1 Model 812 Loudspeakers
- Care and Maintenance
- Additional Resources
10 - English
Operation
F1 Model 812 Control Panel
Note: For a complete list of LED indications and behaviors, see “LED Indicators” on page 20.
POWER/FAULT:
• Blue = power on.
• Red = fault condition.
LIMIT:
• Amber = system limiting (protection mode).
FRONT LED:
• POWER enables front LED to indicate power status.
• LIMIT engages a limiting display on the front LED.
• OFF turns off the front LED.
EQ: (See “Power On/Off Sequence” on page 12.)
• FULL RANGE allows the loudspeaker to function without high-pass filtering.
• WITH SUB engages a high-pass filter (100 Hz) when using the loudspeaker with the F1
subwoofer. Recommended when using with F1 Subwoofer.
LINE OUTPUT:
• Balanced XLR line output provides a mix of input 1 and 2, post input volume control. Can
be used to daisy chain speakers together.
SIGNAL/CLIP: Displays the input signal status
in color.
• Green = signal present.
• Red = signal clipping, input signal too high
VOLUME: Adjusts channel volume.
SIGNAL INPUT: Selector switch sets input
sensitivity for input type. Combo connector
accepts XLR mic connector or ¼" phone
plug (TRS balanced or TS unbalanced
cables).
• MIC selects sensitivity for microphone
inputs (dynamic or self-powered mics
only) – use only when a mic is connected
directly to the input.
• LINE selects sensitivity for line-level in-
puts, for example, from a mixing console
or DJ controller.
RCA connectors: Analog stereo input for
audio sources such as DJ controllers and
other line-level sources. Left and right are
summed, producing a mono audio output
and mono signal to LINE OUTPUT (XLR).
• Left (White)
• Right (Red)
¼" phone connector: Provides analog
input for guitars and other instruments.
Accepts TRS balanced or TS unbalanced
cables.
SIGNAL/CLIP: Displays the input signal
status in color.
• Green = signal present.
• Red = signal clipping, input signal too high.
VOLUME: Adjusts channel volume.
POWER: AC
power on/off
AC power
input
INPUT1
SIGNAL/CUP
-
VOLUME
(')
SIGNAL
INPUT
■
-
MIC
LINE LEVEL
SYSTEM
POWEl=I/FAULT
-
. - POWER
LIMIT
OFF
. -
FULL
RANGE
WITH SUB
LINE OUTPUT
r;
INPUT 1
SIGNAL/CUP
-
VOLUME
(')
r;
SIGNAL
INPUT
. -
MIC
UNELEVEL
r,
-
r;
INPUT2
SIGNAL/CLF
-
VOLUME
(')
~
' r;
~
INPUT
0
POWER
r;
l'OWERIFAIJLT
-
~·
-
FRONT
l£O
,.
-
POWER
UMrr
OFF
,.
-
FULL
RANGE
WTTHSUB
UNEOUTPUT
r.