Solo TV Sound System Owner’s Guide | Brugervejledning | Bedienungsanleitung | Gebruikershandleiding Guía del usuario | Käyttöohje | Notice d’utilisation | Manuale di istruzioni Kezelési útmutató | Podręcznik użytkownika | Manual do Proprietário | Bruksanvisning
Contents Safety Information Introduction Thank you…............................................................................................................ Unpacking.............................................................................................................. 6 6 System Setup Step 1: Place the system................................................................................... Step 2: Connect the Solo system to power..................................................
Safety Information Please read this guide Please take the time to follow the instructions in this owner’s guide carefully. It will help you set up and operate your system properly and enjoy its advanced features. Please save this guide for future reference. All Bose products must be used in accordance with local, state, and federal regulations.
Safety Information WARNING: • To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture. • Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids into any part of the system. Liquids can cause a failure and/or a fire hazard. • Do not place any naked flame sources, such as lighted candles, on or near the apparatus.
Safety Information Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Introduction Thank you… Thank you for choosing the Bose® Solo TV sound system for your home. This stylish, unobtrusive speaker system is designed to fit under most TVs with screens up to 32 inches, and many TVs with screens up to 42 inches. It delivers superb acoustic performance that will greatly enhance your TV viewing experience.
System Setup Step 1: Place the system A. Move your TV aside and turn it so you can see the connection panel. B. Place the Solo system where you had your TV. A B Placement guidelines: • The Bose Solo system is designed to fit under TVs that weigh no more than 40 lb (18 kg) and have bases no wider than 20" (508 mm) and no deeper than 10¼" (260 mm). Many 42" and most 32" TVs and smaller meet these requirements.
System Setup Step 2: Connect the Solo system to power A. Plug one end of the power cord into the AC input connector. B. Plug the other end into a live AC power (mains) outlet. A few moments after applying power, the system emits two tones indicating that it is ready to use. AC input connector 100-240V 50/60 Hz 50W Note: Bose recommends using a safety agency-approved surge protector on all electronic equipment. Voltage variations and spikes can damage electronic components in any system.
System Setup Step 3: Choose the type of audio cable to use On the back of your TV, look for one of the following audio output connections and locate the cable for the one you want to use. Refer to the unpacking diagram on page 6. Choose only one Audio OUT connection Remove cap OR Optical digital audio • A digital audio output that passes digital data through a fiber optic cable. • If available, use this connection for best audio performance.
System Setup Step 4: Plug the audio cable into the Solo system Tip: If you selected the optical digital audio cable, see “Important instructions for optical cable connections” on page 11. A. Plug one end of the selected audio cable into the correct Audio IN connector on the Solo system. Solo system Audio IN Make only one connection OR OR Remove cap B. If you wish, you can slide the cable behind the built-in cable clip. (Optical cable shown only for example.
System Setup Important instructions for optical cable connections 1. Remove the protective cap from both ends of the cable. Remove cap 2. Hold the optical cable plug as shown . Align the plug with the Optical connector and insert the plug carefully . Note: The connector has a hinged door that swings out of the way when inserting the plug. Hinged door CAUTION: Inserting the plug in the wrong orientation can damage the plug and/or the connector. 3.
System Setup Step 5: Plug the other end of the audio cable into your TV A. Find the Audio OUT connections on your TV. B. Plug the other end of the audio cable into the correct Audio OUT connector. CAUTION: If using an optical digital audio cable, make sure you hold the plug in the correct orientation for the Audio OUT connector on your TV. You may need to rotate the plug differently than you did for the Solo system.
System Setup Step 6: Place your TV on the Solo system. Place your TV on the Solo system, making sure the TV stand is centered on the top of the system. Refer to “Placement guidelines:” on page 7. CAUTION: Be sure to center the base of your TV on the top of this product. CAUTIONS: • DO NOT place a CRT type TV on this system. It is not designed for use with this type of TV.
System Setup Step 7: Check your TV settings To enjoy the full benefit of hearing TV audio through the Solo TV sound system, the internal speakers in your TV should be turned off. Also, you need to make sure that some audio settings do not inhibit the audio output signal. Note: Check the user manual for your TV for help on using the TV menus and changing any TV settings. Manufacturers usually make user manuals available on their web sites. A. Turn on your TV. B.
System Setup Step 8: Check for sound A. Press the power button on the Solo system remote. Make sure the system status indicator is solid green. System status indicator B. Make sure your TV is on. C. Check if sound is coming from the Solo system speakers. Tip: To confirm your TV speakers are off, press the mute button on the Solo system remote and check that no sound is coming from the TV. The system status indicator on the front panel blinks green when the system is muted.
Alternate Setup Connections When to use an alternate connection You may discover that your TV does not provide audio outputs or when you have connected one of its audio outputs to the Solo system your TV may not deliver the audio to the Solo system. If you have difficulty getting sound from the Solo system when it is directly connected to your television, one of these alternate connection schemes may help.
Alternate Setup Connections Connecting to a TV headphones output If your TV only has a headphones jack, you can connect this audio output to the Solo system using a Dual RCA to 3.5 mm stereo cable. After making this connection, turn your TV volume up to near maximum and control the volume with the Solo system remote. Audio OUT TV headphones or other variable audio output This connection requires a Dual RCA to 3.5mm stereo cable (not included).
Alternate Setup Connections Connecting multiple devices to the Solo system If you have a device such as a DVD player connected to your TV, you may discover that your TV does not pass audio from the DVD player to the audio output on your TV. The Solo system provides a solution to this problem. You can connect up to three devices to the Solo system using a different type of audio cable for each. For example, the figure below shows a cable box and a DVD player connected to the Solo system.
Operation Remote control The Solo TV sound system is easily operated using the small remote control. Just point the remote at the front of the system and press the buttons. Turns the sound system on or off Raises (+) the system volume Lowers (–) the system volume Mutes or unmutes the system sound System status indicator The system status indicator tells you when the system is on and provides you with a system status during operation. System status indicator System status: Off............................
Operation Decreasing the bass Depending on the placement of your Solo system or the program currently playing, the audio may produce more bass than you would like. To select the decreased bass setting 1. 2. Point the remote at the system. Press and hold the Mute button until the following happens: The system mutes the audio, plays three descending tones (going down) and flashes the status indicator (page 19) amber three times. Audio returns and the status indicator turns solid amber. 3.
Care and Maintenance Troubleshooting Problem What to do TV base is too large to place on the system • Place the sound system in another location such as on an open shelf under the TV. • If possible mount your TV on the wall above the sound system. System will not turn on • Make sure the power cord is securely connected on both ends. • Make sure the power cord is plugged into a live AC (mains) outlet.
Care and Maintenance Replacing the remote battery When the remote stops operating or its range seems reduced, it is time to change the remote battery. WARNING: Keep battery (or batteries) away from children, May cause a fire or chemical burn if mishandled. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Dispose of used batteries promptly. Replace only with a battery of the correct type and model number. 1. Using a coin, turn the battery cover slightly counterclockwise. 2.
Care and Maintenance Customer service For additional help in solving problems, contact Bose Customer Service. Refer to the address sheet included with the Solo TV sound system. In the U.S. only, call: 800-901-0472. Limited warranty Your Bose® Solo TV sound system is covered by a limited warranty. Details of the limited warranty are provided on the product registration card that is included in the carton. Please refer to the card for instructions on how to register.
