User Manual
Table Of Contents
- Bluetooth Headset cover_17L.pdf
- GauguinOG
- Safety Information
- WARNINGS:
- 1. Read these instructions – for all components before using this product.
- 2. Keep these instructions – for future reference.
- 3. Heed all warnings – on the product and in the owner’s guide.
- 4. Follow all instructions.
- 5. Do not use this apparatus near water or moisture – Do not use this product near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, or anywhere else that water or moisture are present.
- 6. Clean only as directed by Bose Corporation. Unplug this product from the wall outlet before cleaning.
- 7. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- 8. Protect the USB cord from being walked on or pinched, particularly at the power supply end and the point where it exits from the apparatus.
- 9. Only use attachments/accessories specified by the manufacturer.
- 10. Unplug this apparatus during lightning storms or when unused for long periods of time – to prevent damage to this product.
- 11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way: such as USB cord or power supply is damaged; liquid has been spilled or objects have fallen into the apparatus; the apparatu...
- 12. To prevent risk of fire or electric shock, avoid overloading wall outlets, extension cords, or integral convenience receptacles.
- 13. Do not let objects or liquids enter the product – as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.
- 14. Use proper power sources – Plug the product into a proper power source, as described in the operating instructions or as marked on the product.
- In the United States:
- In Canada:
- Attribution
- Other agency markings
- Using the headset
- Thank you
- Features
- Functions
- Multipoint pairing
- Maintain two active phone connections at once.
- Hear what is being said, even as noise levels around you change, with automatic volume adjustment.
- Listen to podcasts, audio books, turn-by-turn directions, or other audio sources streamed directly from your mobile device. Automatically connects when an audio source is played.
- Charging
- Although the battery is partially charged at the factory, it is important to fully charge the battery before first use. Allow up to 3 hours for a full charge.
- Initial pairing
- 1. Ensure the mobile phone is on and Bluetooth® is enabled. Turn on the headset by sliding the power switch to the On (green) position.
- 2. Locate the Bluetooth device list on the mobile phone and select Bose BT2.
- 3. If prompted for a passkey, enter 0000.
- Additional pairing (up to 6 phones):
- Press and hold Call for 5 seconds to make the headset discoverable.Then repeat steps 2 to 4 above.
- Fitting
- Wearing
- Recognizing the lights
- Basic call actions and audio tones
- Multi-point pairing
- To maintain an active connection with two different mobile devices at the same time:
- 1. Disable the Bluetooth® connectivity on any phones previously paired to the headset.
- 2. Turn on the headset and the mobile phone.
- 3. Press and hold Call and Volume + for 5 seconds.
- 4. Complete the pairing procedure specific to your phone.
- 5. Turn the headset off and then on again.
- 6. Repeat steps 2 - 5 for the second phone.
- Disabling multi-point pairing
- To maintain an active connection with two different mobile devices at the same time:
- Connection priority for multiple paired phones
- The last phone used for a call will have first priority for calls, voice dialing and redial.
- To make a call with the other connected phone, place the call manually. First priority then switches to this phone.
- To establish priority for any other paired phone, reconnect with that device by selecting Bose BT2 in the device list.
- In multi-point operation, call actions are the same as listed on page 17. To switch between active calls on two phones, press Call twice.
- Troubleshooting
- • Make sure both ends of the USB cable are firmly connected.
- • If you are using a power outlet:
- • If you are using your computer, be sure the computer is plugged in and the USB port is powered.
- • Make sure the room temperature is between 41°F and 104°F (5°C and 40°C) and the product is at room temperature before charging begins.
- • Make sure the headset is in the correct ear and the wing on the StayHear™ tip is flush beneath the ear ridge. (Refer to "Wearing" on page 14.)
- • Make sure the tip is firmly attached to the headset.
- • Try the large or small tip.
- • Make sure both the headset and mobile phone are turned on and the Bluetooth® feature on your phone is activated. Refer to your phone instruction manual for details.
- • Turn the headset off, then on again.
- • Press Call for at least 5 seconds to make the headset discoverable, then attempt to pair again.
- • Make sure the phone is within 33 feet (10 meters) of the headset.
- • Turn the phone power off, then on again and attempt to pair again.
- • Make sure both devices are turned on and Bluetooth® connectivity is enabled on the phone.
- • Turn the headset off, then on again. Make sure the mobile phone is within 33 feet (10 meters) of the headset.
- • Check the Bluetooth device list on your phone to be sure Bose BT2 is selected.
- • Simultaneously hold Call and Volume – for 5 seconds to reset the memory, and pair the headset to the phone again.
- • Turn the phone power off, then on again.
- • During a call, adjust the volume on your mobile phone or on the headset by pressing Volume + or – .
- • Check your mobile phone signal strength.
- • Make sure the mobile phone is within 33 feet (10 meters) of the headset.
- • Reposition the headset. Refer to “Fitting” on page 14.
- • Clean the wire mesh under the tip. See page 26.
- • Move the mobile phone closer to your headset.
- • Make sure the phone is not near other wireless equipment.
- • Reposition the headset. Refer to “Fitting” on page 14.
- • Check your mobile phone signal strength.
- • Turn the phone power off, then on again.
- • Check the headset to make sure it is on and charged.
- • Make sure the mobile phone is within 33 feet (10 meters) of the headset.
- • Check the signal strength on your phone and make sure the battery is sufficiently charged.
- • Make sure the device supports A2DP audio streaming. (The Bluetooth® indicator will glow purple.)
- • Make sure the device’s Bluetooth volume is turned up and not muted.
- • Make sure the streaming audio source is on and playing.
- • Move the device closer to the headset.
- • Try another streaming audio application.
- • Turn the phone power off, then on again.
- • Move the device closer to the headset.
- • Move the device and headset away from any device that could cause interference, such as another Bluetooth® enabled device, cordless phones, a microwave oven, or a wireless computer network router.
- • Reduce the number of Bluetooth applications that are running on your device. (Running multiple applications may reduce the amount of internal resources available to transmit audio. Closing all non-essential applications may improve audio quality....
- • Try another streaming audio application.
- • Turn the phone power off, then on again.
- Customer service
- Maintenance
- Battery care:
- To clean the headset:
- Use a soft, dry cloth to wipe the surface carefully. Do not use liquids or sprays.
- To clean the tip:
- Gently peel the tip from the end of the earpiece. Wash the tip with mild soap and rinse. Dry with a soft cloth. Be sure the tip is completely dry before reattaching to the headset.
- To clean the wire mesh under the tip:
- Gently peel the tip from the end of the earpiece. Lightly brush the mesh screen with a soft, dry cloth. Avoid pressing on the mesh, which could push debris through the mesh and into the headset.
- Limited Warranty
- Your Bose® Bluetooth® headset Series 2 is covered by a limited warranty. Details of the limited warranty are provided on the product registration card that is included in the carton. Please refer to the card for instructions on how to register. Fai...
- To obtain Limited Warranty service
- Return the product, with proof of purchase from an authorized Bose dealer, as follows:
- 1. Contact the Bose organization in your country/region (visit Global.Bose.com for contact information in your country/ region) for specific return and shipping instructions.
- 2. Label and ship the product, freight prepaid, to the address provided by the Bose organization in your country.
- 3. Place any necessary Return Authorization Number prominently on the outside of the carton. Cartons not bearing a Return Authorization Number, where required, will be refused.
- Technical information
- Weight: 0.42 ounces (12 grams)
- Input: 100 VAC to 240 VAC, 0.15A
- Output: 5V, 1A
- Operate this product within the temperature range of -4°F to 113°F (-20°C to 45°C) only.
- Store this product within the temperature range of -4°F to 113°F (-20°C to 45°C) only.
- Charge the battery where the temperature is between 41°F and 104°F (5°C and 40°C) only.
- Rechargeable, non-replaceable lithium-ion polymer.
- Charging time: 3 hours for full charge.
- Use with a fully charged battery: up to 4.5 hours of talk time or 175 hours of standby time. Talk time may vary with specific mobile phones.
- Version 2.1 Enhance Data Rate (EDR) and Secure Simple Pairing (SSP).
- Profiles include Headset (HSP 1.1), Hands Free (HFP 1.5), and Advanced Audio Distribution Profile (A2DP 1.2).
- Accessories
9
English
Tab 6, 12
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11
Functions
Multipoint pairing
Maintain two active phone connections at once.
Adaptive audio adjustment
Hear what is being said, even as noise levels around you change,
with automatic volume adjustment.
A2DP audio streaming
Listen to podcasts, audio books, turn-by-turn directions, or
other audio sources streamed directly from your mobile device.
Automatically connects when an audio source is played.
GauguinOG.book Page 9 Monday, May 16, 2011 1:36 PM