To ensure safety while driving and to comply with laws, drivers should not watch video or operate the video device while driving.
4.
1. HANDLING COMPACT DISCS MOISTURE CONDENSATION On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. NOTES ON CDs Paste or sticky residue. 1. A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge.
2. INSTALLATION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
DIN REAR-MOUNT (METHOD B) Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket. Note: the mounting box, outer trim ring,and half-sleeve are not used for this installation. Screw Factory radio mounting bracket Note: The mounting box, metal half sleeve, hook & screws are not included in the packnig. Hook Screw Hook Dashboard or console DETACHABLE CONTROL PANEL (D.C.P.) Removing The Detachable Control Panel (D.C.P.).
3. ELECTRICAL CONNECTION a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a converter will be necessary). b. Before starting wiring connections, disconnect the power supply by removing the fuse from the fuse box. c. Connect the power wire to one of the extra terminals of the fuse box. d. Connect the black ground wire to a metal part of the car. It is important to make good contact. e. Make other wiring connections as shown. f.
4 PANEL RELEASE BUTTON POWER/ MUTE BUTTON BAND/ LOUDNESS/ APL/NTSC BUTTON CANCEL/ MODE BUTTON TALK BUTTON 8 ENCODER VOLUME KNOB INFRARED REMOTE SENSOR FUNCTION SELECT BUTTON DISPLAY BUTTON LOC BUTTON SCAN BUTTON EJECT BUTTON 8 DSP/ LEFT/ RIGHT BUTTON AMS/ PLAY/PAUSE BUTTON TUNING / SEEK UP/DOWN NEXT/BACK BUTTON E-5 FM MONO / STEREO BUTTON
E-6
5. BASIC OPERATION PANEL RELEASE BUTTON Press this button to remove the control panel. POWER BUTTON Press power button to turn on/off the unit. DISPLAY BUTTON( DISP ) Press this button briefly, the LCD will display the clock for about 3 seconds, MUTE BUTTON ( MUTE) Press MUTE button to mute the sound quickly. the display is flashing Press it again to restore the previous sound level. When mute is on, the Mute indicator on the LCD will light up.
6. SYSTEM SETUP Basic operation of menu setup 1. General setup menu In main menu,touch " "to enter into"SETTINGS"mode. 2.Choose menu setup * Touch cursor and choose setup menu. 3.Enter or exit menu * Touch in the menu and enter into"SETTINGS"menu. * Touch in the SETTINGS menu to exit current setup menu. 4.Menu setup operation TIME SETUP: The unit utilizes a 24 hr time format, touch on the touch screen directly to adjust hour and minute.
7. RADIO OPERATION RADIO FUNCTION KEY Touch the icon in any mode to go back to the main menu and select"RADIO"to enter the radio mode. 15 FM1 CH-00 87.50M 1 87.50MHZ 90.10MHZ 98.10MHZ 106.10MHZ 107.90MHZ 87.50MHZ 12:06 AM 2 3 16 16 4 9 5 10 6 11 7 Serial number Name 12 13 8 14 17 Function description 1 Information 2 CLOCK 3 4 5 6 7 8 9 Radio 10 LOUD LOUDNESS ON/OFF 11 EQ ROCK\POP\CLASS\EQ.
FM MONO / STEREO BUTTON (MONO) Use this control to select stereo or mono reception for FM radio stations. You can sometimes improve reception of distant stations by selecting mono mode. LOCAL / DX BUTTON (LOC) This control can be used to change between Local and Distant (-DX) tuning mode. Local mode improves reception in some areas where the signal is too strong.
8. Bluet ooth Hand Free Panel / Remote Control Function Key Matrix 1 1 4 8 1 3 2 6 BLUETOOTH Function Button 8 3 5 2 9 7 Bluet ooth Hand Free Function Make an Outgoing call press “TALK” Button once to ready input the Tel number what you want to phone and the tel number you dialed will be showed on the Display. Once you press the “TALK” again to dial the number and the “DIALING” will, be showed on display. During the talking mode, the Display will showed “TALKING”.
BLUETOOTH MODE OPERATION INSTRUCTION FOR HANDSFREE FUNCTION 1. PAIR IT WITH YOUR PHONE (PAIRING) Before you use your Car HANDSFREE System,you need to pair it with your mobile phone. 1. The Bluetooth set system on the head unit will automatically go into pairing mode when the Ignition is being turned on and the Bluetooth symbol indicator on the display will Flash every 1 second. 2. Set your Bluetooth phone to ‘discover’ the “CAR_AUDIO_HF”. 3. Your phone will find the “CAR_AUDIO_HF”.
4. BLUETOOTH NOTICE Before you start to use our Bluetooth HEAD UNIT , Please pair the unit with your mobile phone completely. Please refer to the section of “PAIRING” To ensure the best reception for Pairing & Re-connection, please make sure the phone Battery is fully charged when making the pairing or Re-connection. Every time you turn the ignition key from off to on, the unit will automatically re-connect with the mobile phone. By pressing the TALK button the unit will start the Auto-Reconnection .
Specifications for Bluetooth BLUETOOTH Power Consumption Output Power Frequency Band Range Standard 200mA Max. 0 dBm (Class II) 2.4GHz ~ 2.4835GHz ISM Band 3 meters (free space) Bluetooth 2.0 specification Specifications subject to change without notice. Remark: Our Bluetooth Handsfree System adapts to the Bluetooth spec V2.0 and higher. It is compatible with profiles such as Handsfree profile and Head Set profile.
9. DISC/MULTIMEDIA FILES OPERATIONS 2 The playing file is a Music file. The playing file is a Photo file. File Switch Region: Displays the file type of the playing and the switching. Function KEY KEY AUDIO OK OSD MENU TITLE + NUM 10 12 11 S.N NAME FUNCTION Menu Information 13 DESCRIPTION CURRENT DIRECTORY NAME DISPLAY DISC INFO RMATION BACK TO MAIN MENU MOVE CURSOR DIRECTION CONFIRM SELECTED INFORMATION PAUSE/PLAY REPEAT.
MULTIMEDIA FILE OR FOLDER SEARCHING CD SLOT Insert the disc into CD slot. The CD will begin to play. EJECT BUTTON Press this button to eject the CD from the unit. The receiver will switches to radio mode automatically. PLAY/PAUSE BUTTON ( ) Press this button briefly to pause disc play, press again to resume play. NEXT/BACK BUTTONS( & ) When NEXT is pressed, the unit will go to the next track and start the playback. When BACK is pressed, the unit will go back to the preivous track and start the playback.
GO TO BUTTON (GO TO) Using GO TO feature to select track number or specific time. A. Press GO TO button,the screen will display the following message: A TRK 001/021 00:01: 56 B. Press Arrow Left/Right buttons to highlight the track number or the time option. C. Use numeric buttons to enter the track you want to play or the elapsed time you wantto go to in that track. D. Press OK button to start playback.For example entering 00:01:56 will start playback one minutes and fifty-six seconds into the title.
10. PLAY MULTIMEDIA FILES OPERATION Place a disc into the player, and the player will auto search the directories saved files. After searching, it will automatically go to the first directory saved files (to the disc containing both Music and Photo files; To the disc containing single type of files, it will automatically go to the first directory) and play the first song in the directory (“01:” is highlighted).The screen displays as the picture below: Current directory name Current file name.
11. MMC/SD CARD & USB DEVICE OPERATIONS START THE USB DEVICE MODE USB SOCKET P.1 1.The USB mini socket is accessible as indicated in picture 1.(P.1) 2.Plug in the USB drive / device completely as indicated in picture 2(P.2) and display will show “USB” to indicate that the USB drive / device is being plugged in correctly & the download has begun. 3.Does not matter what mode the unit is in, once a USB drive / device is being plugged into the unit, unit will automatically switch to USB mode. P.2 4.
START THE SD/MMC MODE P.4 D.C.P. P.6 1.Press panel release button to release the front panel.(P.4) 2.The SD/MMC card slot is located on top of the front panel as indicated in (P.5). 3. Insert the SD/MMC card into the card slot in the correct direction until a “CLICK” sound is heard. 4.Close the front panel. 5. The display will show “CARD” to indicate that the SD or MMC card is correctly inserted. Once the SD or MMC card is inserted, the file will automatically loaded & playback will also start. 6.
12. VIDEO DISC OPERATIONS DVD TT 01/05 CH 011/018 AUDIO OK OSD MENU NUM TITLE 15 S.N 01:11:56 2 16 17 Name Function Information bar + 19 18 14 1 Description DISPLAY DISC INFO.
10 11 13 12 14 10 11 12 13 14 HUE - / HUE + USER/STDY /BRIG/ SOFT /SHAR PLAY BUTTON ( ) Press this button briefly to pause disc play, press again to resume play. STOP BUTTON( ) Stop the current disc playback. Briefly press the STOP button to stop the unit playback,when the PLAY button is pressed,normal playback will continue. Press STOP two times consecutively to enter the clear stop mode. Under the clear stop mode, if PLAY is pressed, the disc will resume the playback from the beginning of the disc.
NUMERIC BUTTONS Use when playback disc which need numeric Selection or Input, like in the Goto function, etc. PAL/NTSC BUTTON (P/N) In order to achieve the best image display effect, you must adjust the player signal system to match your TV set. 3 types of TV color signal system are available: NTSC, PAL60 or Automatic mode. Use P/N button to select between NTSC/PAL, or automatic mode. REPEAT A-B BUTTON (A-B) 1. Press REPEAT A-B at your chosen starting point. 2.
PBC FUNCTION BUTTON (PBC) Press the “PBC” button to turn on PBC function. The unit will show the song list on the screen of the monitor after the WARNING from the Video CD. Then you can choose the song by pressing the desired number key. Press PBC key return to manual of Video CD, NOTE:This only operates with the PBC function on VCD. GO TO BUTTON (GO TO) Using GO TO feature to select track number or specific time: TT 01/05 CH 011/018 01:11:56 A.
SUBTITLE BUTTON (SUBTITLE) 1. Press SUBTITLE button to bring up the subtitle information which will be shown on the top right corner of the screen. 2. Each time you press SUBTITLE, you can switch to another subtitle available in the disc. NOTE:This only operate if the disc with the SUB TITLE function. ANGLE BUTTON (ANGLE) Press ANGLE button to bring up the angle information which will be shown on the top right corner of the screen.
13. SET UP MENU OPERATION General Steps of Setup Menu 1) Press the Setup button, the main setup menu appears. When the main menu displayed, the Video will auto pause. 2) Press the Left and Right arrow buttons to highlight the icon of the desired page, then press the Down or Right arrow button to activate that page; For example, if you want to setup the video page, press Right to highlight the video icon, the video page will be displayed on the screen.
4) Press the Arrow buttons to highlight the Exit Setup option, then press Enter or Setup again to exit Setup Menu. NOTE: When setup, the pressing setup buttons will turn off the setup menu, while the choices that have been changed will be saved. Setup Items Introduction 1) SYSTEM SETUP The system setup options are illustrated below: TV SYSTEM According to the Color System of the TV, you can choose the TV System. 1. NTSC: Choose this settings if your Multimedia player is connected to a NTSC TV. 2.
TV TYPE 16 : 9 (Wide Screen): Choose this setting if your Multimedia player is connected to a wide screen TV. If you choose this setting and you don't have a wide screen TV, the images on the screen may appear distorted due to vertical compression. 4 : 3 LB (Letter Box): Choosing this setting if your Multimedia player is connected to a normal ratio TV. connector You'll see the movies in their original aspect ratio (height-to-width ratio).
OSD LANGUAGE Highlight the OSD LANGUAGE option, and press the Arrow buttons to choose the OSD language you prefer. Press Enter to confirm, and it will display OSD in that language. AUDIO LANG Highlight the AUDIO LANG option, and press the Arrow buttons to choose the audio language you prefer. Press Enter to confirm. If the disc you are playing has that language available, it will output audio in that language.
14. SPECIFICATIONS CD PLAYER System Usable disc Sampling frequency No of quantization bits Frequency Number of channels S/N Ration Compact disc audio system Compact disc, CD-R, CD-RW 44.1KHz 1bit 5-20,000Hz 2 stereo 70dB RADIO SECTION FM Frequency Range Intermediate Frequency Usable Sensitivity Stereo Separation S/N Ratio 87.5 -108 MHz (EURO) 87.5 -107.9 MHz (USA) 10.