Specifications
~
n
MOUNTING
INSTRUCTIONS
NOTE; The chassis in Fig. 1 appears in expladed view. The angles on which
the tube sockets
are
mounted
are
actua
Ily part of the chassis, but has been
moved up,
out
of the chassis, to make component mountings more obvious.
Refer to Fig. 3 for proper orientation of all components.
1.
(J)
Fig. 1. Mount the 9 pin miniature tube socket with shield base XVI
as shown. Use two
#4-40
screws,
two'4
lockwashers and
two'4-40
hex nuts.
2.
('4 Fig. 1. Mount the 9 pin. miniature tube socket XV6 as shown. Use
two
'4-40
screws, two #4 lockwashers and two
'4-40
hex nuts.
3.
(~
Fig. 1. Similar to the
above,
mount the 9 pin miniature tube sockets
XV2,XV3,XV4 and XV5 as shown. Use two
'4-40screws,
two
'4
lockwashers
and two
'4-40
hex nuts for each
socket.
4.
("~
Fig. 1. Mount the 4 screw terminal board,
TB2
from the outside of the
chassis as shown. Use two
*6-32
screws and two
*6-32
hex nuts. Under one
'6-32
hex nut, mount a *6 ground lug. Under the other
#6-32
hex nut, add a
1 post upright terminal strip,
TB
I, and a *6 lockwasher. .
5.
(tYFig.
1. Mount a 2 post terminal strip, TB3, as shown. Use
one'6-32
screw, one
'6
lockwasher and one
'6-32
hex nut.
6.
(01g.
1. Using the same mounting
hole,
mount a two post with ground
terminal strip, TB9, from the bottom and a two post terminal strip, TB8,'from
the top. Use one #6-32 screw, one
'6-32
lockwasher and one
'6-36
hex
nut.
7.
(...("Fig.
1.
Mount a 2 post with ground terminal strip, T84, as shown.
Use one
'6-32
screw, one
'6-32
lockwasher and one
'6-32
hex nut.
8. (0 Fig. 1. Mount a 1 post right with ground terminal strip, TB5, as
shown. Use one
'6-32
screw, one
'6
lockwasher and one
'6-32
hex nut.
9. ( ) Fig. 1. Mount
Cl'3
post, 2 left with ground terminal
strip,
T86, as
shown. Use one
'6-32
screw, one
'6
lockwasher and one
'6-32
hex nut.
10. ( ) Fig. 1. Using the same hole , mount a 1 post left.terminal
strip,
TB7,
from the top and 30mfd
electrolytic
capacitor'"ICl7,
as shown.
Observe
the
polarity on the
capacitor.
Use one
'6-32
screw,
one'6
lockwasher
and
one
'6-32
hex nut.
11. ( )
Fi~.
1. Mount the
pilot
light
socket,
XII,
as shown. Use
one'6-32
screw, one 6 lockwesher and one
'6-32
hex nut.
12. ( ) Fig. 1. Mount a 1 post left with a ground terminal strip, TB10, as
shown. Use one
'6-32
screw,
one'6
lockwasher and one
'6-32
hex nut.
13. ( ) Fig. 1. Mount input jack board,
JI-2
as shown. Use a
bakelite
insulator between the board and the chassis. Use four
'6-32
screws, four
'6-32
lockwashers and four
'6-32
hex nuts.
14. ( ) Fig.
1. Mount the input Jack
board,
J3-4
as
above.
Use
bakelite
Insulator as
above.
Use four
'6-32
screws, four'610ckwashers and
four'6-32
hex nuts.
15. ( ) Fig. 1. Mount
tape
output
Jack,
J5,
as shown. Use
two'6-32
screws,
two
'6
lockwashers and two
'6-32
hex nuts.
16. ( ) Fig. 1. Mount the hum adjustment
pot,
R30 as shown. Use
one)/8
flatwasher, one
3/8
Iqckwasher and one
3/8
hex nut. Bend upper and lower
lugs so that they
neither
protrude over bottom of chassis or touch the chassis
proper.
17. ( ) Fig. 1.
Mounttheconvenienceoutlet,
J6 asshown. Use two
'6-32
screws, two
'6
lockwashers and two
'6-32
hex nuts.
18. ( ) Fig. 1. Push the grommet through the remaining
3/8
hole in the rear
of the chassis.
19. ( ) Fig. 1.
Mount'6
ground lug
"I".
Use a
'6-32
screw and a
'6-32
hex
nut.
See Fig. 5.
20. ( ) Fig.
1. Mount a 1 post left terminal strip,
TB
11, as shown. Use one
#6-32 screw, one
'6-32
lockwasher and one
'6-32
hex nut.