Specifications
~
WIRING
INSTRUCTIONS
1. ( ) Fig.
3.
Cut
a 6" length of
black
wire and 6" length of brown wire.
Connect
one end of the brown wire to
XVl-9
(5) and one end of the black wire
to
XVl-4
(5) through
XVI-5
(5). Twist the two wires and run along
the
chassis
as shown.
Connect
the
other
end of the black wire
toXV4-4
(C) and the
other
end of the brown wire to XV4-5 (C).
2. ( ) Fig. 3 . Following
the
above
pracedure,
cut
a 4" length of black wire
and a 4" length of brown
wire.
Connectane
end of the black wire to XV4-4 (5)
and
one
end of
the
brown wire to XV4-5 (5). Twist the two wires and run
a-
long the chossls as shown.
Connect
the
black
wire to XV5-4 (C) and the brawn
lead to XV5-S (C) .
3. ( ) Fig. 3. Following the above procedure,
cut
a 4" length of black wire
and a 4" length of brown wire.
Connect
one end of the
black
wire to XV5-4(5)
and
one end of the brown wire
toXV5-5($).
Twist
the
two wires and run along
the chassis
as shown.
Connect
the black wire to XV3-5 (C) through XV3-4 (C)
and
the
brown wire to XV3-9 (C).
4.
( ) Fig. 3 . Following the above
pracedure,
cut
a 3" length of black wire
anda
3"'ength
af brawn
wire.
Cannect
ane
end
oftheblackwire
toXV3-5(5)
and
one
end of
the
brown wire
toXV3-9(C).
Twist the two wires and run along
the chassis as shawn.
Cannect
the
black
wire to XV2-4 ($) through XV2-S (5)
and the brown wire to XV2-9 (5).
S. ( ) Fig. 3. Following the above
procedure,
cut
a 4" length of black wire
anda
4" length of brown
wire.
Connect
one end of the black wire
toXV3-4
(5)
and one end of the brown wire
toXV3-9(5).
Twist the two wires and run along
the chassis as shown.
Connect
theblack
wire
toXV6-S(C)
and the brown wire
to XV6-4 (C).
6.
( ) Fig.
3.
Following
the
above
procedure,
cut
a 6" length of black wire
and a 6" length of brown
wire.
Connect
one
end
ofthe
black wire to XV6-5 (C)
and one end of the brown wire
toXV6-4
(C) . Twist the two wires and run along
the chassis as shown.
Connect
the black wire to
XIl-1
(5) and the brown wire
to XI1-2 (5) .
7. ( ) Fig. 3 . Following the above
procedure,
cut
a 6" length of black wire
and a 6" length of brown
wire.
Connect
one
endof
theblack
wire
toXV6-5(5)
and one end of the brown wire to XV6-4 (5). Twist the two wires and run along
the chassis as shown.
Connect
the
black
wire to R30-1 (C) and the brown wire
to R30-3 (C).
8.
( ) Fig. 3 . Twist
the
two green leads from the power transformer, T2, and
run along the chassis as shown.
Connect
one green lead to R30-3 (5) and the
other green lead to R30-1 (5). '
9. ( ) Fig. 3.
Connect
a 6"
piece
of yellow
wirefromXV4-3
(C)toR30-2
(5).
10. ( ) Fig.
3.
Connect
a 3"
pieceofyellow
wire from XV4-3
(5)toXVS-3
(C).
11. ( ) Fig. 3.
Cut
both leads of the
16SQ,
5W resistor, R28, to 1" . Put
3
/4"
of spaghetti on one lead and
leave
the
other
lead
bare.
Connect
the
lead
with the spaghetti to XVS-3 (C) and the
other
lead to ground
lug"
A" (5) on XV4.
12. ( ) Fig.
3.
Cut
the lead on the positive end (+) of the SOmfd, 2S
volt
electrolytic
capacitor,
CIS,
to I
1/2"
and the lead on the
negative
(-)
to I
1/4".
Put I
1/
4" spaghetti on the lead of the positive end and
connect
toXVS-3
(5).
Connect
the
negative
lead to ground
lug"
B"
(5) on XV6.
13. ( ) Fig.
3.
Cut
the lead on the positive (+) end of the
30mfd
capacitor,
C17,
to 2
1/2"
and the tead on the
negative
(-)
end to 3
/4".
Put 2
1/4"
spa-
ghetti on the positive lead and
connect
to XV6-9 (C).
Connect
the
lead
on
the
negat
ive end to
TB
10-2
(C).
14. ( ) Fig.
3.
Connect
a 1"
piece
of
bare
wire
fromXV6-9(5)toXV6-3
(C).
15. ( ) Fig.
3.
Twist
the
red leads from the power transformer, T2. Run the
leads along the chassis as shown.
Connect
one
red leadXV6-1 (5)and
the
other
red lead to XV6-7 (5).
16. ( ) Fig.
3.
Twist the
red-yellow
and the
white
leads from the power
trans-
former
T2
.
Connect
ta ground lug
"0"
(5).
17. ( ) Fig.
3.
Connect
one
black lead from the power transformer, T2, to
J6-1
(C) and
the
other
black
lead to
J6-2
(C).
18. ( ) Fig.
3.
Connect
an 8
1/2"
black
wire from
TBI
(C) to
XV3-8
(C).
19. ( ) Fig.
3.
Connect
the
following leads from the output transformer TI,
to the output terminal board
TB2:
Green
lead to TB2-3(5)
Yellow lead to TB2-4(C)
Brown lead to TB2-2(5)
Black lead to TB2-I(C).
20.
( ) Fig. 3.
Connect
a 3
1/2"
red lead from XV6-3(5) to XVS-9(C).
21. ( ) Fig.
3.
Connect
a 3 1/2" red lead from XVS-9(S) to XV4-9(C).
22.
( ) Fig.
3.
Connect
a 1"
piece
of
bare
wire from TB2-1 (5) to ground
"E" (5).
23.
( ) Fig.
3.
Connect
a 4"
piece
of black wire fromTB3-1 (C)toTB9-2 (C).