Specifications
1. ( ) Fig. 4.
Cut
both leads on the 22KQ (red, red, orange,gold) 5% resis-
tor, R29, to
3/4".
Connect
from TB2-4 (C) to
TBl
(C).
2. ( ) Fig. 4.
Cut
both leads on a 47mmf, 10% disc ceramic
capacitor,
C14,
to
3/4".
Connect from TB2-4 (5) to
TBl
(5).
3. ( ) Fig. 4.
Connect
a 4" red lead from TB3-2 (C) to
C18-3
(C).
4. ( ) Fig. 4.
Connect
a 4
1/2"
red lead from
C18-2
(C) to T84-3 (C).
5. ( ) Fig.
4.
Connect
a.
4.
7KQ
(yellow,violet,
red,silver)
resistor, R6,
from
XVl-3
(C) to
TB3-1
(C).
Cut
both leads to
3/4".
6. ( ) Fig. 4. Connect a 10mfd, 6V
elec
capacitor
C21 from
XVI-3
(5) to
TB3-1 (C). Cut both leads to
3/4".
Use
:/2"
pi
ece
of spaghetti on (+) side.
The
(+) side goes to XVl.
7. ( ) Fig. 4.
Connect
a 1MQ (brown,
black,
green, silver) resistor, R7, from
XVl-2
(C) to T83-1 (5).
Cut
both leads to
3/4".
S. ( ) Fig. 4.
Connect
a 200KQ (red,
black,yellow,
gold) resistor, R4, from
XV1-l (C) to C1S-3 (C).
Cut
both leads to
1/2".
-0
n 9. ( ) Fig. 4.
Connect
a 200KQ
(red,black,yellow,gold)
resistor, R3, from
XVl-6
(C) to TB3-2 (5).
Cut
both leads to 1".
10. ( ) Fig. 4.
Connect
a 68KQ
(blue,grey,orange,silver)
resistor, R31,
from C
lS-2
(C) to C
lS-3
(5). Cut both leads to
3/4".
11. ( ) Fig. 4.
Connect
a 33KQ (orange, orange, orange, siIver) 10% resistor,
R32, from
C1S-2
(5) to C1S-1 (C). Cut both leads to
3/4".
12. ( ) Fig.
4.
Connect a 10KQ (brown, black, orange, silver) 1
watt
resistor ,
R1S,
from C1S-1 (C) to T84-1 (C).
Cut
both leads to
3/4".
13. ( ) Fig. 4. Connect a 4" red lead from XV4-9 (C) to T84-1 (5).
14. ( ) Fig. 4.
Connect
a
2.2KQ
(red,red,red,silver)
resistor, R5, from
XV1-S (C) to TB9-2 (C). Cut both leads to
3/4".
15. ( ) Fig. 4.
Connect
a 10KQ (brown, black, orange, silver) resistor, Rl0,
from
XVl-7
(5) to TB9-3 (C). Cut both leads to
1/2".
16. ( ) Fig. 4.
Connect
a . 25mfd paper
capacitor,
Cl,
from
XVl-2
(C) to
XVl-6
(5). Cut both leads to
3/4".
Be careful not to short lead to
center
lug
of socket.
17. ( ) Fig. 4.
Connect
a .025mfd disc ceramic
capacitor,
C2, from
XV1-l
(5) to
TB9-1
(C).
Cut
both leads to
3/4".
18. ( ) Fig. 4.
Connect
a 5" red lead from C18-1 (5) to TB6-2 (C).
19. ( ) Fig. 4. Twist the
red,brown-yellow
and blue leads on the output
transformer, Tl ,
Connect
the brown-yellow lead to XV4-7 (5), the red lead
to XV4-9 (5) and the blue lead to XV5-7 (5).
20. ( ) Fig. 4. Connect a 33KQ (orange,orange,orange,silver) resistor, R14,
from TB4-3 (C) to XV2-1
(c).
Cut both leads to
3/4".
21. ( ) Fig. 4. Connect a 100KQ (brown,black,yellow,silver) resistor, R15,
from TB4-3 (5) to XV2-6 (C). Cut both leads to 1".
22. ( ) Fig. 4.
Connect
a 3.3KQ (orange,orange,red,si Iver) resistor, R17, from
T84-2
(C) to XV2-8 (5). Cut both leads to
3/4".
23. ( ) Fig. 4.
Connect
a 4"
piece
of black wire from
TB
10-1 (C) to TB4-2 (C).
24. ( ) Fig. 4. Cut one lead on the .25mfd
capacitor,
C7, to
3/4"
and the
other lead to 1". Cover the shorter lead with
1/2"
spaghetti and
connect
to
XV2-1 (5). Running the
capacitor
along the chassis as shown,
connect
the longer
lead to
TB
11 (C).
25. ( ) Fig. 4. Connect a 1.2KQ (brown,red,red,silver) resistor, R16, from
XV2-3
(C) to
T81O-1
(C). Cut both leads to
3/4".
26. ( ) Fig. 4. Connect a 6800mmfdisc ceramic
capacitor,C20,fromXV2-3(5)
to
TB
10-1 (5). Cut both leads to 1".
27. ( ) Fig. 4. Cut one lead on
the.l
mfd
capacitor,
C8, to
3/4"
and the
other
lead to 1
1/2".
Cover the shorter lead with
1/2"
spaghetti on the longer lead
with 1
1/4"
of
spaghetti.
Connect
the longer lead to XV2-6(5) and the shorter
lead to XV3-7
(C).
28. ( ) Fig. 4. Cut an 8"
piece
of single conductor shielded
cable.
5trip the
outer rubber insulation back
3/4".
Unwrap the metal shield. Cut off the metal
braid
On
One end of the
cable
while twisting together all strands of the metal
braid
On
the other end of the
cable.
5trip the inner insulation back
1/4"
on
both ends of the
cable.
Connect
the metal braid to ground lug "H"
(5)on
socket
XV3. Connect the inner lead on the same end of the
cable
to
XV3-7
(C). Run
the
cable
along the chassis as shown and COnnect the other end of the inner
lead to
J5
(5).
29. ( ) Fig. 4. Connect a 1.8KQ (brown,grey,red,gold) 5% resistor, R20, from
XV3-8 (5) to
TB
10-2
(5). Cut both leads to
3/4".
30. ( ) Fig. 4. Cut the plus (+) lead of the
25mfd-6V
elec.
capacitor,
C5,
to 1", end the minus (-) lead to 1
1/2".
Cover the 1" lead with a
3/4"
piece
of spaghetti and connect to
XVl-8
(5). Cover the 1
1/2"
lead with a 1
1/4"
piece
of spaghetti and connect to TB9-2 (C).
31. ( ) Fig. 4. Connect one end of a 4
1/2"
piece
of black wire to T811 (C).
Push the other end throuqh hole "Y".