Specifications

6 . Connect a I" piece of bare wire from XV3-6 (S) to XV3-2 (C).
~. 6. Connect a 100KO (brown,b lack,yellow,gold) 5% resistor,
KV3-3 (C) to
TBS -l (C). Cut both leads to 3 /4".
ig. 6 . Connect a 200 mmfd disc ceramic capacitor, CIl, from
to T85-1 (C).
Cut both leads to 1" .
ig. 6.
Connect a . 025 mfd disc ceramic capacitor, C13, from
to T85-2 (C) .
Cut both leads to 3 /4" .
ig. 6.
Connect a 470KO (yellow,vio let,yellow,sllver) resistor,
KV3-2
(C) to T86-2 (C). Cut both leads to 3 /4".
ig.6 . Connect a 100KO (brown ,black,yellow,gold) 5% resistor,
KV3-1 (C) to T86-2 (C). Cut bath leads to 3
/4 " .
. 6.
Connect a 150 mmfd disc ceramic capacitor, C9, from XV3-2
1 (C).
Cut both leads to 3 /4".
ig. 6 . Connect a .025 mfd disc ceramic capacitor, CI2, from
to T86-4 (C).
Cut both leads to 3 /4" .
ig . 6.
Connect a 200 mmfd disc ceramic capacitor, Cl0, from
to T86-3 (C).
Cut both leads to 3 /4".
'ig . 6. Connect a 330KO (orange, orange, yellow, siIver) resistor,
T85-1 (S) to TBS-2 (C). Cut both leads to
1/ 2" . Push the resistor
rds the chassis .
'ig. 6. Connect a 330KO (orange,orange ,yellow, silver) resistor,
T86-3 (S) to T86-4 (C).
Cut both leads to 1/ 2" . Push the resistor
rds the chassis.
ig. 6.
Connect a 10KO (brawn,black, orange, silver) resistor, R21,
(S) to T86-2 (S). Cut both leads to
1/ 2 ". Push the resistor down
~ chassis.
ig. 6.
Connect a 10KO (brown, black, orange, silver) resistor, R26,
I (S) to XV5-2 (S). Cut both leads to 3 /4". Run resistor over pin 8
thcur touching pin .
ig. 6.
Connect a 10KO (brown, black, orange, silver) resistor, R27,
! (5) to XV4-2 (S). Cut both leads to 3 /4". Run resistor over pin 8
Ihout touching
pin.
15. (-2(C ).
from J
Run a esistor,
J2
-2 (,
the
ben
I, from
16. (
RI, Fr c
" from
17. (
under
Unwroeslstor,
to 3 /4
(S), th
--t o J4-esistor ,
18. (
ing thr.
and twXV3-2
nect tl
19. (
to
XVl, from
20. (
from T,
), from
21. (
T89-1
22. ( esistor,
blac k resisto r
23. (
yellow
resistor,
24. ( resistor
the ch
the Iir
conne-r, R21,
25. ( ,r down
lead ~
leads I
26. ( 'r, R26,
brown
sr pin 8
27. (
resisto
28. ( Ir, R27,
R35, rer pin 8
TBll (
15. ( ) Fig. 6 . Run 01 1/ 2" pie ce of bore wire covered with I" of spaghetti
from
JI-2 (S) to J2 -2 (C). Run on iden tica l wire from J3-2 (C) to J 4-2 (5).
Run a 1"
piece of bore wire covered wit h 1 /2" of spaghetti from J3 -2 (C) to
J2-2 (C). Be careful not to touch any mounting screw or the bare chassis with
the bare wire.
16. ( , Fig, 6. C
onnect a 100KO (brown, black, ye llow, silver) resistor,
R
I, from J3- 1 (C) to J3-2 (S).
17. ( , Fig. 6 .
Run the four conductor shielded cable from rectangular hole
under Sl along the chassis as shown. CUf the
outer insulation bac k I 1 /2 ".
Unwrap the metal shield and twist the shie lded strands.
Cut the metal sh ield
to 3 /4" and the red and orange leads to I". Connect the brown lead to JI-I
(S), the red lead to J2-1 (S), the orange lead to J3-1 (S) and the yellow lead
--t o J4-1 (S). Connect shield to J2-2 (5).
18. ( ) Fig. 6. Strip the outer insulation of the single conductor cable (pass-
ing through the rectangular hole under Sl ) back 3
/4" . Unwrap the shie ld strands
and twist shield strands together. Strip the inner conductor back
1/ 4" . C on-
nect the inner conductor to T89-3 (C) and the outer shield to T89-2 (C).
19. ( ) Fig. 6.
Connect the yellow lead from the rectangular h ole under SI
to
XVl-2 (5) and the green lead from the same hole to TB9-1 (C).
20. ( ) Fig. 6. Connect a 470KO
(yellow,vio let, yel low, silver) resistor, R2,
from TB9-3 (S) to T89-2 (C).
21. ( ) Fig. 6.
Connect a 2200mfd disc capaci tor, C19, from T89-2 (S) to
T89-1 (5). Cut both leads to 3
/4 " .
22. ( ) Fig. 6.
Connect the green lead from ho le" X.. to XV2-2 (C) and the
blac k lead to T84-2 (C).
23. ( ) Fig. 6.
Connect the green lead from hole "Y" to XV2-7 (C) and the
yellow lead from hole
"Y" to XV3-7 (5).
24. ( ) Fig. 6. Push the line cord through the grommet
near j6 at the rear of
the chassis. Tie a knot on the inside of the chassis 8" from the tinned end of
the line cord. Split the two leads
apart until the knot. Cut one lead to 3" and
connect to J6-1 (5).
25. ( ) Fig. 6.
Connect one end of a 10" brown lead to J6-2 (S). Twist this
lead with the rema ining lead from the line cord and dress as shown. Push both
leads through hole
"Z".
26. ( ) Fig. 6. Connect the line cord lead from hole"Z" to 52-2 (S) and the
brown lead to S2-1 (5). See Fig. 5.
27. ( ) Fig. 6. Cut both leads on a
470KO (yel low, violet, ye l
low,s ilver)
resistor, R36, to 3
/4 ". Connect from XV2-7 (5) to T84-2 (5).
28. ( ) Fig. 6. Cut both leads on a 270KO (red,
violet, yellow, silver) resistor,
R35, to 1
1/4" and cover each with a 1" piece of spaghetti. Connect from
TBll (5) to XV2-2 (5).