BV7300 User’s Manual - page 1
Safety information CAUTION: This mobile DVD player is a Class 1 laser product. However, this mobile DVD player uses a visible/invisible laser beam which could cause hazardous radiation exposure if directed. Be sure to operate the mobile DVD player correctly as described in this manual. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not open covers and do not attempt to repair this product yourself.
Preparing new discs with rough spots A new disc may have rough edges on its inside and outside edges. If a disc with rough edges is used, the disc will not be properly seated and the player will not play the disc. Therefore, remove the rough edges in advance by using a ballpoint pen or pencil as shown on the right. Press the side of the pen or pencil against the inside and outside edges of the disc. Installation Notes: - Choose a mounting location where the unit will not distract the driver.
1. DIN front-mount (method A) Installation opening This unit can be installed in any dashboard opening with dimensions as shown below: Installing the unit Be sure to test all connections first, then follow these steps to install the unit. 1. Make sure the ignition is turned off. Disconnect the cable from the vehicle battery negative (-) terminal. 2. Disconnect the wire harness and the antenna. 3.
then disconnect the cable from the vehicle battery negative (-) terminal. 2. Remove the metal strap attached to the back of the unit (if present). 3. Press the release button to remove the front panel. 4. Lift the top of the outer trim ring then pull it out to remove it. 5. Insert both of the supplied keys into the slots at the middle left and right sides of the unit then pull the unit out of the dashboard. Using the detachable front panel Removing the front panel 1. Press the RELEASE down the front panel.
Wiring diagram WATCHING THE VIDEO MONITOR IS FORBIDDEN WHILE DRIVING: The “PARKING BRAKE” wire must be connected to the parking brake system of your car. The LCD screen will display video images ONLY when the parking brake is engaged. If the parking brake is not engaged, the screen will display the message “DISABLED WHILE DRIVING”. This is a safety feature designed to prevent the driver from watching a video while driving. The video output of this unit is not affected by this.
Operation Features and controls Front panel Front panel button legend 1 2 3 4 5 6 7 8 9 10 11 POWER ( ), MODE VOL+/IR Sensor 1 2 INTRO (Intro Scan) 3 RPT (Repeat Mode select) 6 GO TO 5 STOP 4 RDM (Random Playback Mode select) USB Port BAND 12 13 14 15 16 17 18 19 20 RELEASE ( ) DISP (Display) (Fast Reverse), TUNE/TRACK Down MUTE (turns audio off) (Fast Forward), TUNE/TRACK Up ST (Stereo/Mono select), LOC (Local/Distance select) MENU AS•PS (Automatic Search/Program Search) A/V Input Connector BV7300 Use
Back of front panel Remote control button legend 1 2 3 4 5 6 21 22 23 24 25 7 8 9 10 11 SD/MMC card slot Disc slot EJECT ( ) LED Warning light RESET button 12 13 14 15 16 17 18 Remote control 1 2 14 3 15 4 16 5 17 6 18 7 19 8 20 9 21 10 22 11 23 12 24 25 13 26 27 BV7300 User’s Manual - page 8 19 20 21 22 23 24 25 26 27 POWER ( ) DISP (Display) A > B (repeat section from A to B) RPT (Repeat Mode select) ZOOM Cursor (arrow) keys: UP/DOWN/RIGHT/LEFT ENTER SETUP (TUNE/TRACK Down, L
To avoid damage, please follow these precautions: - Do not subject it to excessive shock. - Do not carry in a pocket. - Do not leave in direct sunlight. Battery replacement The remote control uses a lithium button type battery, model CR 2025 3V. Do not use any other kind of battery in the remote. Follow these instructions when installing or replace the battery. 1. Remove the battery holder by pressing the locking tab with your thumb, and slide the battery holder out.
Adjusting the Volume Level Press VOL+/- to adjust the volume level. Last position memory - During disc, USB or SD/MMC card playback, press and hold the to turn off the unit, when you next turn on the unit, the DVD unit will resume playing from the point that it was interrupted. - During disc, USB or SD/MMC card playback, if you press MODE to switch to a different mode, when you next return to DVD mode, playback will resume from the point at which it was interrupted.
A/V menu settings You can adjust various settings of the unit from the AV menu. The AV menu contains the menu items and submenus shown in the figure below: 1. Press MENU to activate AV menu. 2. Use the arrow buttons to select a menu item. 3. Press VOL+/- button to increase or decrease the parameter you have selected. 4. Repeat steps 2 and 3 to adjust other items if necessary. 5. Press ZOOM or MODE to return to previous menu. 6. Press MENU to finish the procedure.
Audio menu AUDIO MENU VOLUME 00 FADER BASS 00 EQ R.F CLAS TREBLE 00 LOUD OFF BALANCE L.R SUB.W ON 1. Press the arrow buttons to select a menu item you wish to adjust. 2. Press VOL+/- button to adjust the item selected. Volume level: 0 to 63 Bass level: -7 to +7 Treble level: -7 to +7 Balance: 15L to 15R This setting adjusts the balance between the left and right speakers. Fader: 15R ~ 15F This setting adjusts the balance between the front and rear speakers.
Picture menu PICTURE MENU BRIGHT 00 TINT 00 CONTRAST 00 DISP.M 4:3 COLOR 00 DEFAULT OFF 1. Use the arrow buttons to select a menu item you wish to adjust. 2. Press VOL+/- button to adjust the item selected. Brightness: 0 to 63 Adjust this setting if the picture is too bright or too dark. Contrast: 0 to 63 Use this setting to adjust the contrast of the picture. Color: 0 to 63 Use this setting to adjust the color of the picture.
Setup menu SETUP MENU SYSTEM TIME ON TIME.M 12 AM 11 : 0 0 Hour Minute 1. Use the arrow buttons to select a menu item you wish to adjust. 2. Press VOL+/- button to adjust the item selected. 3. Repeat steps 1 and 2 to adjust other items if necessary. 4. Press ZOOM or MODE to return to previous menu. Time: ON/OFF Turns the clock display on/off. Time.M: 12 / 24 Use this setting to select 12 hour clock mode or 24 hour clock mode.
Disc operation Loading/Removing a disc 1. Press the button (7) to flip down the front panel. 2. Insert a disc with the label side facing up. The disc will be drawn into the player automatically. The information for the current disc will be shown on the screen. * To eject the disc, press the button. When you insert a DVD disc, a screen similar to the one below will appear when you press the SUB-T button: For CD: Selecting tracks in single steps -Press button or button to skip to the previous or next track.
For CD/VCD/SVCD: REP 1 REP ALL For MP3: REP 1 REP DIR OFF For DVD: REP CHAPTER OFF REP OFF REP ALL REP TITLE REP REP NOTES: REP 1: Only one track (file) is played repeatedly. REP DIR: A single folder of tracks is played repeatedly. REP CHAPTER: A chapter is played repeatedly. REP TITLE: A title is played repeatedly. REP ALL: An entire disc is played repeatedly. REP OFF: Normal playback mode. Note: The Repeat feature is not supported for VCD 2.0 discs when PBC (Playback Control) is on.
AUDIO button to switch between the audio languages recorded on the disc. Notes: - The number of available languages varies from disc to disc. - Some discs only contain one soundtrack language. - Not all discs will allow changing the subtitle during playback. In these cases, select subtitle select mode from the DVD’s menu. Notes: - Some time may be required for the angle to change. - Depending on the disc, the viewing angle may switch in one of two ways. 1. Seamless: The angle switches smoothly. 2.
1) Use the / / / cursor buttons to select the item that you want to program. The item you selected will be highlighted. 2) Input the track number that you want to program using the numeric buttons (0-9) on the remote control. 3) Press the / / / cursor buttons to move to “PLAY” operation button and then press the ENTER button to program the playback sequence.
Data disc playback USB playback When you insert a data disc including audio (MP3), movie (MPEG4) or picture (JPEG) files into the disc slot, the following main menu will appear: This disc player features a front panel USB interface (10). A USB device can be connected to this port. When you insert a USB device into the USB connector, the DVD player will read the USB automatically. The unit gives priority to a disc or SD/MMC card.
Memory card playback This disc player features a SD/MMC memory card slot. When you insert a SD/MMC card into the memory card slot, the DVD player will read the SD/MMC card automatically. The unit gives first playback priority to the card in the slot. If you insert a disc into the disc slot while reading the SD/MMC card, the unit will play the disc. Press the MODE button to switch back to the card reading mode. Note: When reading the memory card, please don’t touch or remove the card.
Setup In DVD mode, when the disc is playing or in stop mode, press SETUP button to enter the Setup menu. 1. When the cursor is in the upper part of the menu, use / buttons to move between the different pages. 2. Press button to move the cursor to the setup page below. Then you can use the / buttons to move between the different setup options. 3. Press or the ENTER button to move to the choice list of each setup option, and then use / buttons and ENTER button to adjust your selection. 4.
way to view this is in (4:3) letterbox format. You can see the full picture, but there will be a black band at the top and bottom of the screen. 4) Press the / button to select the restriction level (1 to 8) and then press the ENTER button. 5) When the setting is complete, press the SETUP button to return to normal mode. DEFAULT Select DEFAULT and confirm it to restore all the System Settings to those programmed at the factory, except the Parental Controls and Password.
More about this player MENU LANG: ENGLISH/GERMAN/SPANISH/FRENCH/ PORTUGUESE/ITALIAN/RUSSIAN/POLISH Audio setup When you open the AUDIO menu, you will see the following screen: 1) AUDIO OUT: Change among SPDIF/OFF, SPDIF/RAW and SPDIF/PCM. 2) KEY: Change among b, -4, -2, 0, +2, +4, #. Digital setup When you open the DIGITAL SETUP menu, you will see the DIGITAL SETUP screen: 1) OP MODE: Change among LINE OUT/ RF REMOD. - LINE OUT: LINE OUT mode, with digital dialog normalization.
Playing MP3 discs What is MP3? MP3 (MPEG-1 Audio Layer 3) is a compression standard prescribed by the ISO, the International Standardization Organization and MPEG, which is a joint activity institution of the IEC. MP3 files contain compressed audio data. MP3 encoding is capable of compressing audio data at extremely high ratios, reducing the size of music files to as much as one-tenth their original size. This is achieved while still maintaining near-CD quality.
Specifications [ GENERAL ] Power Supply Requirements: DC 12 Volts, Negative Ground Chassis Dimensions: 7”W X 6.3”D X 2”H Tone Controls: - Bass (at 100 Hz) +10 dB - Treble(at 10 kHz) +10 dB Maximum Output Power: 80W X 4CH Current Consumption: 15 Ampere (max.) [ DVD PLAYER ] Signal to Noise Ratio: > 50 dB Channel Separation: > 40 dB Frequency Response: 20Hz - 20 KHz [ MONITOR SCREEN ] Screen: 3.
Troubleshooting If it appears that your DVD unit is faulty, please first consult this checklist. It may be that something simple has been overlooked. Under no circumstances should you try to repair the player yourself, as this will void the warranty. Only qualified service personnel may remove the cover or service this player. No Power If the power supply is connected to the car accessory circuits, but the engine is not turned on, switch the ignition key to “ACC.” Check if the fuse is blown.
