PRECAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ! WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Wires Connection Description Description of Wires Connection Fixing Screw Bolt GREEN Wiring Connecting Socket 2 PARKING LINE WHITE REVERSAL LINE BLACK IPod IN Wiring Connecting Socket 1 Radio Antenna jack BLACK BLACK USB LINE IN BLACK video out yellow KEY GROUND(BLACK) KEY A(BROWN) KEY B(YELLOW) from the bottom cover of the chassis 1. Parking wire must be connected. And the parking brake must be engaged in order for the monitor to work. 2.
UNIT INSTALLATION INSTALLATION INSTRUCTIONS THE UNIT IS INSTALLED TO BE AN ANTI-THEFT ONE. THE CHASSIS OF THE UNIT WEARS A SLIDING METAL HOUSING. PLEASE DO THE CONNECTION OF THE POWER, SPEAKERS AND ANTENNA ACCORDING TO THE REQUIREMENT OF THE INSTRUCTION BOOK , THEN INSTALL THE SLIDING METAL HOUSING IN THE CAR AS FOLLOWS. TO BOOST UP THE CAPABILITY OF ANTI-JAMMING, PLEASE FIX THE METAL STRAP ON THE METAL CONNECTED TO THE BOTTOM BRACKET OF THE CAR.
GENERAL KNOWLEDGE ABOUT REMOTE CONTROL 1. Removing insulating sheet If using remote control for the first time, you can see an insulating sheet at the bottom side of remote control as right. you must remove the insulating sheet as right. Otherwise, the remote control is disabled. 2. Replace lithium cell If the electric energy of lithium cell is weak, replace it.
Remote Control Description 1. ANG BUTTON 2. MENU BUTTON 3. POWER BUTTON 4. ^ BUTTON 5. >>| BUTTON 6. > BUTTON 7. |<< or CLEAR BUTTON 8. v BUTTON 9. SEL BUTTON 10. PLAY/PAUSE BUTTON 11. NUMBER(0~10,+10 -10) BUTTONS 12. 10+/PTY BUTTON 13. SETUP BUTTON 14. MODE BUTTON 15. APS or HANG UP BUTTON 16. SEARCH BUTTON 29. MUTE BUTTON 17. RDM BUTTON 30. STOP BUTTON 18. RPT BUTTON 31. VOLUME- BUTTON 19. SUBTITLE or REDIAL BUTTON 32. < BUTTON 20. TITLE/PBC or PAIR BUTTON 33. OK BUTTON 21.
Locations and Names of Controls on or in the unit 11 8 18 19 2 10 3 26 TA / AF 1 OPEN - VOL + MODE BAND REL APS IR MUTE 1 2 INT 3 RPT 4 RDM 5 -10 6 +10 MIC AUX SEL 9 12 15 24 13 16 17 14 22 23 4 6 25 Front Panel SD/MMC 20 21 5 7 The Front Facet after removing front panel 1. OPEN button 2. POWER/MUTE button 3. Monitor 4. AUX socket 5. Disc Slot 6. USB Jack 7. SD/MMC Card Slot 8. MODE button 9. SEL button and VOL knob 10. ^ button 11. v button 12. PLAY/PAUSE/1 button 13.
Common Operation 1. To turn on/off the unit In power off mode, short press any buttons except REL to turn on the unit. In power on mode, long press the POWER button on the front panel or short press the POWER button on the remote control to turn off the unit. 2.
11.To remove the front panel press the REL button to flip down the front panel from the main unit, then hold the right end of the front panel to push leftward and pull away. 12.To reset the player When the monitor , the small LCD display or some buttons are not working or sound is distorted, remove the front panel, then press the RESET button to reset the program to factory default. Audio Setting 13.
the 4th Page of the General Setting the 5th Page of the General Setting the 6th Page of the General Setting In the 4th page, you can set the ASPECT RATIO, BRIGHNESS, CONTRAST, SATURATION and STANDARD VIDEO. In the 5th page, you can set RADIO REGION. In the 6th page, you can calibrate the screen. 16. Backlight Setting In the Mode Menu 2 screen, tapping the Backlight icon can pop up the Backlight Setting interface. In the interface, tapping the - or + icon can set the backlight.
The icons in the foreground radio interface describe as follows: : To return to the Radio Rear Setup interface. < and > : To automatically search up or down for an available station. CH- and CH+ : To manually search up or down for a desired station. CH- CH+ the Foreground Radio interface 19. Change Color of the LCD In the Mode Menu 3 screen, tapping the CC LCD icon can pop up the CC LCD interface. In the interface, tapping the or icon can change the color of the LCD.
4. APS BUTTON In RADIO mode: 1) When long pressing the APS button, the radio searches from the lowest frequency and checks the signal strength level until 1 cycle search is finished. And then the 6 strongest stations are preset to the corresponding preset number memory bank. The AS operation is implemented in each bank of the selected band.
When PTY group is on, pressing the 6 number buttons also can select one of PTY programs as above. After selecting one of the PTY programs, it will display SEEK PTY and automatically search for the station of the PTY program. If the station of the PTY program does not exist, it will display PTY NONE and then return back to the normal station. 9.
Disc, USB and Card Operation 1. Load/unload disc , USB or Card To play files in a disc, press the REL button to flip down the front panel, then insert the disc into the disc slot and flip up the front panel and push it onto the chassis till click, then it will automatically play . To remove the disc from the unit, press the REL button to flip down the front panel, then press the EJECT button to eject disc from the disc slot and then you can remove it.
In the File Playing interface, tapping any place in the rectangle of the screen can pop up the Keyboard-1 of MP3/WMA, then tapping the icon can pop up the Keyboard-2 of MP3/WMA. Remark2: After loading a CD disc, the screen will display the CD interface as right. In the CD interface, tapping the icon can pop up the number interface and use the icons of the number, <-- and OK to select a desired track to play; use the or icon to track up or down.
2. Pause Playback When playing DVD/VCD/CD/MP3/WMA , press the PAUSE button on IR remote control to pause the playback, press the PLAY button to resume normal playback. 3. Stop Playback When playing DVD/VCD/MP3/WMA/CD , press the STOP button once to pause the playback, then press the PLAY button to resume the normal playback; press the STOP button twice to full stop the playback, then press the PLAY button to start playing from the beginning of the first chapter/track. 4.
2. Press the direction buttons to select your desired title, and then press the OK or PLAY button to open the root menu of the selected title. 3. Press the direction buttons to select your desired chapter, finally press the OK or PLAY button to play the selected chapter. During playback, pressing the MENU button can directly display the root menu of the title that is playing. In VCD mode 1.
During slow forward, press the PLAY button to resume normal playback. This function is only for video. 9. Display still frame step by step If the unit is currently playing video, press the TEL button consecutively to display still frame step by step. Press the PLAY button to resume normal playback. 10. Playback Repeatedly 10.1 ONE/ALL Repeat 1. In the mode of DVD playback: Press the RPT button to select REP CHAPTER, REP TITLE, REP ALL or REP OFF. 2.
11. Playback in Scan Mode 1. When playing VCD(PBC OFF)/CD , press the INT button to play the previous 15 seconds part of each track on the disc. Press the INT button again to resume normal playback. 2. When playing DVD/MP3/WMA , the INT button is not available. 12. Playback from a specified chapter/track or a specified time 1.
ZOOMx2,ZOOMx3,ZOOMx4,ZOOMx1/2,ZOOMx1/3,ZOOMx1/4,ZOOM OFF. Press one of the ^/v/>/< buttons to select the area you want to enlarge. 16. Change Caption Language When playing DVD , press the SUBTITLE button repeatedly to select the language of the caption or turn off the caption.(depend on the media used.) When playing VCD/MP3/WMA/CD , the button is not available. 17. Change Audio Language 1. When playing DVD , press the AUDIO button repeatedly on the IR remote control to select the desired language type.
20. Program Playback It allows you to enter the order in which you want some chapters/tracks in DVD/VCD/MP3/WMA/CD to play. 1 During playback, press the PROG button to enter a program interface as follows: for DVD/MP3/WMA for VCD/CD 2 Use the direction buttons to move cursor onto the desired place for inputting the sequence number. 3 Use the number button to input desired sequence number of title/chapter/ track with desired sequence.
3. During JPEG playback, press one of the >/: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHT During JPEG playback, press the PROG button to change the mode of refresh picture. During JPEG playback, press the STOP button to stop playing and return to the root menu. * * During JPEG playback, the following buttons are not available: SLOW-FWD, SUBTITLE, TITLE, ANGLE, AUDIO, RDM, INT and A-B.
For the DVD System Menu, there are 6 setup titles. They display as follows: 24.1 SYSTEM SETUP TV TYPE The setup item is for matching monitor screen size. 4:3 PS: Choose this item when connecting a monitor with 4:3 screen. When playing the pictures with 16:9 size, the left and right parts of the image will be cut out, and display in full screen. 4:3 LB: Choose this item when connecting a monitor with 4:3 screen.
.2 LANGUAGE SETUP OSD LANGUAGE This item is for selecting the language of the SYSTEM MENU and all operating prompt interface displayed during playback. AUDIO LANG This item is for selecting a audio language. SUBTITLE LANG This item is for selecting a subtitle language. MENU LANG This item is for selecting a disc menu language. 24.3 AUDIO SETUP KEY It is for selecting your desired basic music tone(from low to high). 24.4 VIDEO SETUP BRIGHTNESS It is for adjusting the brightness of the video output.
HUE It is for adjusting the hue of the video output. SATURATION It is for adjusting the saturation of the video output. SHARPNESS It is for adjusting the sharpness of the video output. 24.5 SPEAKER SETUP DOWNMIX It is for selecting your desired sound effect when there is not central speaker and sub-woofer. There are 3 mode: LT/RT, STEREO, VSS. LT/RT: When playing a disc with PRO LOGIC stereo effect, choose the item, so it will output audio signal with vivid theatre effect.
AUX IN operation An external AV system can use the car AV system as monitor and amplifier. 1. Use an AV cable to make the car AV system and the external AV system connected through the AUX IN jack on control panel(audio only) or the AV IN jacks from the rear cabinet of the car AV system and the AV Out jacks of the external AV system. 2. Play the external AV system, then use MODE button or the Mode Menu to enter AUX IN mode for the car AV system.
REAR VIEW CAMERA The car AV system can make you look at the actual status behind your car when you change the gear level to the back position. 1. Use an video cable to make the car AV system and the rear view camera connected through the REAR CAMERA INPUT jack in the rear cabinet of the car AV system and the VIDEO OUTPUT jack of the rear view camera. Make the REAR CAMERA SWITCH line in the rear cabinet of the car AV system connected to (B+)12V power supply. 2.
iPod Operation 1. Enter iPod mode When inserting the iPod plug into an iPod , it will enter iPod mode and display the File Playing interface on touch screen as follows: The File Playing interface You can also use MODE button or Mode Menu to enter iPod mode. 2.
BLUE TOOTH HANDFREE SYSTEM 1. Enter Bluetooth mode To enter the Bluetooth mode, press the MODE button or tap the Bluetooth icon. It will display the Phone page of the Bluetooth interface as right. Tapping the icon can pop up the Book page of the Bluetooth interface, tapping the icon can pop up the Music page of the Bluetooth. the Phone page of Bluetooth interface In Bluetooth interface, the icons describe as follows: : Transfers audio between the Car Audio System and mobile phone.
4. In the connection status: the audio of mobile phone transfers to the car audio system whenever calling out or receiving a call. 5. Dialling when in connection status 5.1 Dial with the mobile phone directly. 5.2 Dial with remote control with the following procedures: (1) Input telephone number with number buttons 0-9 * Press CLEAR button briefly to cancel the wrongly input number if necessary (2) Press TEL briefly to execute the dialling. 5.
Trouble Shooting Please read the user’s manual carefully before using the DVD player. If you have any troubles in using this player, try to solve the problems by the suggestions mentioned below. If you can not remove the trouble after using all the suggestions, please contact the company or the technical service center authorized by us. For the sake of your safety, please do not open the cover and repair the player by yourself, if that, it may cause electric shock.
Specification General Specification Power Supply Requirement..................................................DC 12V Maximum Power Output............4 x 80W(measured at DC 14.4 V) Dimensions(w x h x d).....................................7”W x 2”H x 6.3”D DVD Deck Specification Format.....................................DVD/VCD/JPEG/MP4/MP3/WMA/CD Video System....................NTSC/PAL/PAL-M/PAL-N/AUTO(optional) Audio System..............................................................