User Manual
Table Of Contents
- IMPORTANT NOTES
- Before Using CD-R/RW Discs
- Notes When Using Mics
- Contents
- Introduction to the BR-900CD
- Panel Descriptions
- Quick Start
- Connecting Peripheral Devices
- Turning On / Off the BR-900CD
- Listening to a Demo Song
- Recording/Playing Back a Song
- (1) Preparing the Memory Card
- (2) Turning On the Power
- (3) Selecting the Song to Record
- (4) Connecting Instruments
- (5) Using Insert Effects
- (6) Using the Rhythm
- (7) Basic Recording
- (8) Playing Back Recorded Music
- (9) Overdubbing (Recording an additional performance while listening to an existing performance)
- (10) Adjusting the Sound for Each Track
- (11) Bouncing (Putting multiple tracks together)
- (12) Turning Off the Power
- (13) Removing the Memory Card
- Section 1 Recording and Playback
- Recording
- Repeating Playback (Repeat)
- Re-recording Only a Mistake (Punch-in/out)
- Canceling an Operation (Undo/Redo)
- Putting Multiple Tracks Together (Bounce)
- Loading Songs Created with the BR-864/BR-532
- Displaying the Song Information
- Section 2 Editing
- Registering Time (Locator)
- Search for the Music’s Start and End (Scrub/Preview)
- Editing the Performance on a Track (Track Editing)
- Organizing the Songs You’ve Recorded
- Creating a Master Tape / Disc
- Section 3 Using Effects
- Using the Insert Effects
- Insert Effect Parameter Functions
- Mastering
- Mastering Tool Kit Parameter Functions
- Using the Loop Effects/Track EQ
- Loop Effect Parameter Functions
- Track EQ Parameter Functions
- Fixing the Pitch of Vocals (Pitch Correction)
- The Pitch Correction
- Makeup of the Pitch Correction
- Pitch Correction Patches
- Precautions for Pitch Correction Usage
- Using the Pitch Correction
- Setting the Correction Method for Vocal Pitch (Pitch Correction Edit)
- Saving the Pitch Correction Settings (Write)
- Making Detailed Settings for Pitch Correction (Correction Event Map)
- Section 4 Using the Rhythm
- Section 5 Using the CD-R/ RW Drive
- Section 6 Using MIDI
- Section 7 Using USB
- Section 8 Other Convenient Functions
- Adjusting the Display Contrast
- Using a Foot Switch or Expression Pedal
- Tuning an Instrument (Tuner)
- Mixing the Output from an External MIDI Device with the Output from Your BR-900CD (Audio Sub Mix)
- Using Condenser Microphones (Phantom Power)
- Copying Difficult Songs (Phrase Trainer)
- Initializing the BR-900CD’s Settings
- Conserving Battery Power (Power Save)
- Utility Parameter List
- Section 9 Appendices
211
Section 9
Troubleshooting
If the BR-900CD does not function as you expect, please
check the following points before assuming that a
malfunction has occurred.
If this does not resolve the problem, contact a nearby Roland
service center or your dealer.
Problems with the Sound
No sound
❍ Is the power of the BR-900CD and of the connected
equipment turned on?
❍ Are the audio cables connected correctly?
❍ Are any audio cables broken?
❍ Has the volume of the connected amp or mixer been
lowered?
❍ Has the MASTER fader or headphone volume of the
BR-900CD been lowered?
❍ Is a memory card inserted?
❍ Has the wrong card been inserted?
You can use commercially available CompactFlash cards
as memory cards for the BR-900CD; The 3.3 V type with
the capacities of 32 MB to 1 GB can be used.
❍ Are you attempting to play back a short phrase of less
than 1.0 seconds?
Phrases of 1.0 seconds or less cannot be played.
The volume level of the instrument
connected to GUITAR/BASS jack or
LINE IN jacks is too low
❍ Could you be using a connection cable that contains a
resistor?
Use a connection cable that does not contain a resistor.
A specific track cannot be heard
❍ Has the track volume been lowered?
❍ Is the V-Track setting for a different V-Track?
❍ Has the track been muted?
The input source cannot be heard
❍ Did you adjust the SENS knob?
❍ Has INPUT SELECT been muted? (The INPUT
SELECT indicator will be dark.)
❍ Has the INPUT LEVEL knob been set to “MIN”?
❍ If you are using the internal microphone, is “Mic”
under UTILITY set to “ONBRD+EXT”?
Cannot record
❍ Is a song protected?
❍ Is a memory card inserted?
❍ Does the memory card have insufficient remaining
capacity?
❍ Has the recording mode (REC MODE) been selected
correctly?
❍ Has the Phrase Trainer or Scrub Playback function
been turned on?
The recorded sound contains noise or
distortion
❍ Is the input sensitivity set appropriately?
If the input sensitivity is too high, the recorded sound
will be distorted. If it is too low, the input sound will be
buried in noise. Adjust the SENS knob so that the level
meter moves as much as possible without causing the
PEAK indicator to light.
* Set it so the “0” is not indicated in the level meter.
❍ Are the track output levels appropriate?
If you hear noise or distortion after bouncing tracks, the
output level of the tracks was too high.
❍ Is a mic with high output impedance connected
directly to the BR-900CD?
The BR-900CD is designed with a wide margin of
headroom. Also, since the MIC 1 and MIC 2 jacks are low
impedance inputs, the recording level may be too low,
depending on the response of some mics. In such cases,
connect the mic via a mic preamp to the LINE IN jacks
on the BR-900CD before recording.
Cannot digitally record to an external
device
❍ Does the sampling rate of the BR-900CD match that of
the digital audio device?
Set the digital audio device to a sampling rate of 44.1
kHz.
❍ Does the digital signal format match?
Your digital audio device may use a non-standard digital
signal format. Connect the BR-900CD to a digital audio
device that supports CP-1201 or S/P DIF.