COMMAND LIGHT P.O. BOX 87 LOVELAND, CO 80539 PHONE: FAX: WEB: 1-800-797-7974 1-800-667-4296 www.commandlight.
12/16/2002 Breakage or Damage During Shipment The transportation company is fully responsible for all shipping damage and will resolve problems promptly if you handle it correctly. Please read these instructions carefully. Examine the contents of all shipping cases. If you find any damage, call your transportation agent at once and have them make a description on the freight or express bill describing the damage and the number of pieces. Then write us and we will send you the original bill of lading.
12/16/2002 Product Safety Precautions x Never operate the COMMAND LIGHT SHADOW near overhead high voltage power lines. The COMMAND LIGHT SHADOW is manufactured from electrically conductive materials. x Do not use the COMMAND LIGHT SHADOW for uses other than its’ intended purpose. x Do not move emergency vehicle with the light extended. Visually verify that the light is completely nested before moving vehicle. x Do not change light position while people are located within its’ operating envelope.
12/16/2002 Installation Requirements The Command Light Shadow must be installed by a designated facility by qualified personnel only. All safety precautions must be thoroughly understood before installation. Please consult the factory for additional installation information or assistance. Refer to the drawing below to determine the location of the required (4) mounting hole locations. The COMMAND LIGHT SHADOW weighs 70 pounds. Use assistance to lift the light into position.
12/16/2002 To assure a weather tight installation apply a bead of silicone based gasket sealer to the underside of the mounting bosses and bolt heads.
12/16/2002 Electrical Wiring COMMAND LIGHT SHADOW control wires are routed through 3 self-sealing connectors. To install, drill 3 7/8” diameter holes 2-1/2” center to center. Apply silicone sealer to underside of connector before inserting into hole. Fasten connector securely with nuts. Run the control wires from the control box through the vehicle and connect to the COMMAND LIGHT SHADOW. Power Connections Make power connections to the control box as illustrated below.
12/16/2002 Maintenance Lamp Replacement Tools required: Clean oil-free cloth Cleaning alcohol Position lamp tree so lamps are readily accessible. Disconnect the power supply from the COMMAND LIGHT SHADOW. Allow sufficient time for the lamps to cool. The surrounding metal lamp housings can cause serious burns. Grasp the lamp lens bezel firmly, release the latch that holds the lamp bezel in place. Use caution, the lamp bezel and lens may fall if not properly grasped.
12/16/2002 Technical Specifications Dimensions: SL445 Retracted Extended Height 7½ ” 48” Length 48” Width 22” Weight: 70 pounds Lamp Current Draw / Power Requirements: Max @ 110 VAC 500 watt bulbs Generator Requirement 2Kw minimum 18 amps Actuator Current Draw / Fuse Requirement 14 amp @ 12 VDC full load 12 seconds to full actuator extension Relay Protection Lights Cole-Hersey 3055 20 8
12/16/2002 Limited Warranty One Year COMMAND LIGHT warrants that the equipment is free from defects in materials and workmanship when used and operated for a period of one year. The responsibility of COMMAND LIGHT under this limited warranty is limited to the repair and replacement of any parts found defective. Parts are returned to COMMAND LIGHT at 1303 East 11th Street, Loveland, Colorado 80537 with transportation charges prepaid (C.O.D. shipments will not be accepted).
20 in / 508 mm 18 in / 457 mm 20 in / 518 mm 18 in / 457 mm 15 in / 375 mm 20 in / 508 mm 44 in / 1120 mm 7 in / 187 mm SHADOW RT 4 X 500 WATT 120 VAC 51 LBS.
Command Light, Inc. PO Box 87 Loveland CO 80539 Phone: 1-800-797-7974 FAX: 970-667-4296 Internet: www.commandlight.