User Manual

ManualsBrandsBostitch ManualsKitchen15-Gauge Angled Finish Nailer

N52FN/N62FN

INDUSTRIAL OIL FREE ANGLED FINISH NAILERS

CLAVADORA INDUSTRIAL EN BARRA ANGULA LIBRE DE LUBRICACIÓN

CLOUEURS INDUSTRIEL DE FINITION EN BANDES SANS HUILE

107740REVD 12/00

BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO

UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE

INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,

CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.

ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR

ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE SEGURI-

Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA

PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESEN-

DE BOSTITCH O CON SU DISTRIBUIDOR.

LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE

ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX AVERTISSE-

GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS AVEZ DES

QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE BOSTITCH.

OPERATION and MAINTENANCE MANUAL

MANUAL DE OPERACIÓN Y DE MANTENIMIENTO

MANUEL D’INSTRUCTIONS ET D’ENTRETIEN

Stanley Fastening Systems

Summary of content (12 pages)

PAGE 1
N52FN/N62FN INDUSTRIAL OIL FREE ANGLED FINISH NAILERS CLAVADORA INDUSTRIAL EN BARRA ANGULA LIBRE DE LUBRICACIÓN CLOUEURS INDUSTRIEL DE FINITION EN BANDES SANS HUILE OPERATION and MAINTENANCE MANUAL MANUAL DE OPERACIÓN Y DE MANTENIMIENTO MANUEL D’INSTRUCTIONS ET D’ENTRETIEN BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.
PAGE 2
INTRODUCTION The Bostitch N52FN/N62FN series nailers are precision-built tools, designed for precise high volume nailing.These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before operating the tool and understand the safety warnings and cautions.
PAGE 3
SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
PAGE 4
N52FN/N62FN TOOL SPECIFICATIONS All screws and nuts are metric. MODEL N52FN N62FN LENGTH 14-11/16” (373mm) 14-11/16” (373mm) HEIGHT 10” (254mm) 11-5/8” (295mm) WIDTH 3-1/4” (83mm) 3-1/4” (83mm) WEIGHT 3.7lbs (1.69kg) 3.8lbs (1.75kg) FASTENER SPECIFICATIONS: TOOL MODEL NAIL SERIES N52FN FN1600 N62FN FN1500 GAUGE 16 15 WIRE SIZE .060 (1.52mm) .072 (1.82mm) FASTENER RANGE 1”-2” (25mm-50mm) 1” - 2-1/2” (25mm-63mm) TOOL AIR FITTING: This tool uses a 1/4” N.P.T. male plug. The inside diameter should be .
PAGE 5
AIR SUPPLY AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses should have a minimum of 150 p.s.i. (10.6 kg/cm2) working pressure rating or 150 percent of the maximum pressure that could be produced in the air system.
PAGE 6
LOADING THE N52FN/N62FN EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
PAGE 7
TOOL OPERATION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
PAGE 8
TOOL OPERATION CHECK: CAUTION: Remove all fasteners from tool before performing tool operation check. 1. TRIGGER OPERATED TOOL: A. With finger off the trigger, hold the tool with a firm grip on the handle. B. Place the nose of the tool against the work surface. C. Pull the trigger to drive. Release the trigger and cycle is complete. CAUTION: THE TOOL WILL CYCLE EACH TIME THE TRIGGER IS PULLED! 2. CONTACT TRIP OPERATION: A. With finger off the trigger, press the contact trip against the work surface.
PAGE 9
MAINTAINING THE PNEUMATIC TOOL When working on air tools, note the warnings in this manual and use extra care evaluating problem tools. CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand.
PAGE 10
TROUBLE SHOOTING PROBLEM CAUSE Trigger valve housing leaks air Trigger valve stem leaks air Frame/nose leaks air O-ring cut or cracked . . . . . . . . . . . . . .Replace O-ring O-ring/seals cut or cracked . . . . . . . . .Replace trigger valve assembly Loose nose screws . . . . . . . . . . . . . . .Tighten and recheck O-ring or Gasket is cut or cracked . . . .Replace O-ring or gasket Bumper cracked/worn . . . . . . . . . . . . .Replace bumper Damaged gasket or seal . . . . . . . . . . .
PAGE 11
Always disconnect air supply: 1. Before making adjustments; 2. When servicing the tool; 3. When clearing a jam; 4. When tool is not in use; 5. When moving to a different work area, as accidental actuation may occur, possibly causing injury. “DIAL-A-DEPTH™” FASTENER CONTROL ADJUSTMENT Shallow The DIAL-A-DEPTH™ Fastener Control adjustment feature provides close control of the fastener drive depth; from flush with the work surface to shallow or deep countersink.
PAGE 12
ACCESSORIES AVAILABLE: N80K2 N62-MAGKIT Remote Cycle Kit N62 Magazine Assembly Kit IMPORTANT NOTE: Steel finish nails are made from galvanized steel wire and not treated after nails are manufactured. As such, we do not guarantee or warranty product against corrosion for any specified time.