N79PT/N90PT PNEUMATIC STICK NAILERS CLAVADORA NEUMÁTICA ALIMENTADA POR BARRA CLOUEUR PNEUMATIQUE EN BANDES OPERATION and MAINTENANCE MANUAL MANUAL DE OPERACIÓN Y DE MANTENIMIENTO MANUEL D’INSTRUCTIONS ET D’ENTRETIEN BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
INTRODUCTION The Bostitch N79PT/N90PT is a precision-built tool, designed for high speed, high volume nailing. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before operating the tool and understand the safety warnings and cautions.
SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
N79PT/N90PT TOOL SPECIFICATIONS All screws and nuts are metric. TOOL ACTUATION MODEL LENGTH HEIGHT WIDTH WEIGHT N79PT/N90PT Sequential Trip with Contact Trip option 20” (508mm) 14” (355mm) 5-7/16” (138mm) 8.75lbs (4Kg.) N79PT-2/N90PT-2 Sequential Trip 20” (508mm) 14” (355mm) 5-7/16” (138mm) 8.75lbs (4Kg.) FASTENER SPECIFICATIONS: This tool uses a wide range of nail sizes in lengths of 2” to 3-1/2” (50 - 90mm) and shank diameters of .113” to .131” (2.8 - 3.
AIR SUPPLY AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses should have a minimum of 150 p.s.i. (10.6 kg/cm2) working pressure rating or 150 percent of the maximum pressure that could be produced in the air system.
LOADING THE N79PT/N90PT EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
TOOL OPERATION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
TOOL OPERATION CHECK: CAUTION: Remove all fasteners from tool before performing tool operation check. 1. CONTACT TRIP OPERATION: A. With finger off the trigger, press the contact trip against the work surface. THE TOOL MUST NOT CYCLE. B. Hold the tool off the work surface, and pull the trigger. THE TOOL MUST NOT CYCLE. C. With the tool off the work surface, pull the trigger. Press the contact trip against the work surface. THE TOOL MUST CYCLE. D.
MAINTAINING THE PNEUMATIC TOOL When working on air tools, note the warnings in this manual and use extra care evaluating problem tools. CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand.
TROUBLE SHOOTING PROBLEM CAUSE Trigger valve housing leaks air Trigger valve stem leaks air Frame/nose leaks air O-ring cut or cracked . . . . . . . . . . . . . . . .Replace O-ring O-ring/seals cut or cracked . . . . . . . . . . .Replace trigger valve assembly Loose nose screws . . . . . . . . . . . . . . . . .Tighten and recheck O-ring or Gasket is cut or cracked . . . . . .Replace O-ring or gasket Bumper cracked/worn . . . . . . . . . . . . . . .Replace bumper Damaged gasket or seal . . . . . . . . . .
DIRECTIONAL EXHAUST DEFLECTOR Loosen screw as shown. Adjust to desired exhaust direction and tighten screw. ACCESSORIES AVAILABLE BC601 BC601 BC602 BC603 BC604 SEQ5 851325 851385 854006 ORK11 BK3 CNTK2 TVA11 4 oz. Bostitch Air-Tool Lubricant. 4 oz. Bostitch Air -Tool Lubricant 1 pint Bostitch Air -Tool Lubricant 1 pint Bostitch “Winter-Formula” Air-Tool Lubricant 1 quart Bostitch Air -Tool Lubricant Sequential Trip Conversion Kit (Dark Gray Trigger) Locite Grade 271 (.02 oz.) Locite Grade 242 (.02 oz.
INTRODUCCIÓN La N79PT/N90PT de Bostitch es una herramienta fabricada con precisión diseñada para trabajos de clavar de alta velocidad y de gran volumen. Estas herramientas darán un servicio eficiente y seguro, siempre y cuando sean utilizadas correctamente y con cuidado. Como con cualquier herramienta automática de calidad, el mejor rendimiento se obtiene siguiendo las indicaciones del fabricante.
INSTRUCCIONES DE SEGURIDAD Cuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas que se encuentren en el área de trabajo, SIEMPRE deben usar PROTECCIÓN OCULAR que cumpla las especificaciones ANSI para resguardo contra partículas volantes arrojadas desde el FRENTE o los LATERALES. Dicha protección ocular se requiere para proteger contra residuos y remaches volantes, que podrían causar graves lesiones en los ojos.
ESPECIFICACIONES DE LA HERRAMIENTA N79PT/N90PT Todos las medidas de tornillos y tuercas son métricas. MODELO N79PT/N90PT N79PT-2/N90PT-2 ACTIVACIÓN DE HERRAMIENTA LARGO ALTURA Disparo secuencial con opción de disparo por contacto 508 mm (20") 355 mm (14") 138 mm (5-7/16") 4,0 kg. (8 lb. 2 onzas) ANCHO PESO Disparo Secuencial 508 mm (20") 355 mm (14") 138 mm (5-7/16") 4,0 kg. (8 lb.
SUMINISTRO DE AIRE Y CONEXIONES No use oxígeno, gases combustibles o gases embotellados como una fuente de suministro para esta herramienta, ya que la herramienta puede estallar, posiblemente causando lesiones. CONEXIONES: Instale un enchufe macho en la herramienta que fluya libre y que descargue la presión de aire de la herramienta cuando sea desconectada de la fuente de suministro.
CÓMO CARGAR EL N79PT/N90PT Cuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas que se encuentren en el área de trabajo, SIEMPRE deben usar PROTECCIÓN OCULAR que cumpla las especificaciones ANSI para resguardo contra partículas volantes arrojadas desde el FRENTE o los LATERALES. Dicha protección ocular se requiere para proteger contra residuos y remaches volantes, que podrían causar graves lesiones en los ojos.
OPERACIÓN DE LA HERRAMIENTA Cuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas que se encuentren en el área de trabajo, SIEMPRE deben usar PROTECCIÓN OCULAR que cumpla las especificaciones ANSI para resguardo contra partículas volantes arrojadas desde el FRENTE o los LATERALES. Dicha protección ocular se requiere para proteger contra residuos y remaches volantes, que podrían causar graves lesiones en los ojos.
VERIFICACIÓN DE LA OPERACIÓN DE LA HERRAMIENTA: ¡PRECAUCIÓN: Quite todos los sujetadores de la herramienta antes de efectuar la verificación de la operación de la herramienta! 1. OPERACIÓN DE DISPARO POR CONTACTO: A. Apriete el disparador de contacto contra la superficie de trabajo, sin tocar el gatillo. LA HERRAMIENTA NO DEBE EFECTUAR SU CICLO. B. Sostenga la herramienta alejada de la superficie de trabajo, y hale el gatillo. LA HERRAMIENTA NO DEBE EFECTUAR SU CICLO. C.
MANTENIMIENTO DE LA HERRAMIENTA NEUMÁTICA Al trabajar con herramientas neumáticas, tenga presente las advertencias que se hacen en este manual, y sea particularmente cuidadoso al evaluar herramientas problemáticas. PRECAUCIÓN: El resorte de empuje (resorte de fuerza constante): Se debe tener cuidado al trabajar con el ensamblaje de resorte. El resorte está enrollado alrededor de, pero no sujetado a, un enrollador.
DIAGNÓSTICO DE FALLA PROBLEMA CAUSA CORRECCIÓN Fuga de aire en la envoltura de la válvula disparadora. Vástago de la válvula disparadora tiene fuga de aire. Fuga de aire en el armazón/nariz. Anillo en O cortado o rajado Reemplazar el anillo en O. Anillos en O/sellos cortados o rajados. Reemplazar anillo en O/sellos. Tornillos de nariz flojos. Anillo en O/empaquetadura cortada o rajada Amortiguador rajado/desgastado. Empaquetadura rajada. Amortiguador de la válvula de cabeza rajado/desgastado.
DEFLECTOR DE ESCAPE DIRECCIONAL Afloje el tornillo según se muestra. Ajuste a la dirección de escape deseada y apriete el tornillo. ACCESORIOS DISPONIBLES BC601 BC602 BC603 BC604 SEQ5 851325 851385 854006 ORK11 BK3 CNTK2 TVA11 4 onz.
INTRODUCTION Le N79PT/N90PT de Bostitch est un outil construit avec précision; conçu pour réaliser un travail rapide à débit maximum. Ces cloueurs sont faits pour assurer un service efficace et durable, à condition d’être utilisés avec un minimum d’attention et dans des conditions normales d’utilisation. Comme pour tout autre appareil pneumatique, les consignes du fabricant doivent être impérativement suivies, afin d’obtenir de bonnes performances de ce matériel.
CONSIGNES DE SÉCURITÉ UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’AVANT et des CÔTÉS, doit toujours être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement au réseau d’air, du chargement, du fonctionnement et de la maintenance de l’outil.
CARACTÉRISTIQUES DU N79PT/N90PT Toutes les mesures des vis et des boulons sont dans le système métrique. MODÈLE N79PT/N90PT N79PT-2/N90PT-2 MÉCANISME DE CONTACT Déclenchement séquentiel avec option de déclenchement au contact Déclenchement séquentiel LONGUEUR 508 mm (20 po) HAUTEUR 355 mm (14 po) LARGEUR 138 mm (5-7/16 po) POIDS 4,0 kg. (8 lb. 2 oz) 508 mm (20 po) 355 mm (14 po) 138 mm (5-7/16 po) 4,0 kg. (8 lb.
ALIMENTATION EN AIR COMPRIMÉ ET RACCORDEMENT L’oxygène, les gaz combustibles ou les bouteilles de gaz ne doivent en aucun cas être employés comme source d’énergie, car ils peuvent exploser et provoquer des blessures. RACCORDEMENTS : Installer le raccord mâle sur l’appareil. Lors du désaccouplement de la source d’énergie, le raccord mâle doit permettre rapidement la mise à l’atmosphère de toute pression résiduelle.
CHARGEMENT DU N79PT/N90PT UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’AVANT et des CÔTÉS, doit toujours être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement au réseau d’air, du chargement, du fonctionnement et de la maintenance de l’outil.
FONCTIONNEMENT DE L’APPAREIL UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’AVANT et des CÔTÉS, doit toujours être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement au réseau d’air, du chargement, du fonctionnement et de la maintenance de l’outil.
VÉRIFICATION DU SYSTÈME DE DÉCLENCHEMENT : ATTENTION : retirer toutes les attaches de fixation de l’outil avant de procéder à une vérification du fonctionnement de celui-ci. 1. SYSTÈME DE SÉCURITÉ À LA VOLÉE : A.Enfoncer l’élément palpeur sur la surface de travail sans actionner la détente. L’APPAREIL NE DOIT PAS SE DÉCLENCHER B.Éloigner l’appareil de la surface de travail et appuyer sur la détente. L’APPAREIL NE DOIT PAS SE DÉCLENCHER C.
ENTRETIEN DE L’APPAREIL Lors de l’utilisation d’un outil fonctionnant sous-pression, lire les avertissements du manuel et user d’extrêmes précautions lors de la découverte d’un problème. ATTENTION : Ressort-poussoir (ressort à poussée constante). Il est recommandé d’user de prudence lors de la manipulation du système du ressort. Le ressort est enroulé autour du rouleau mais n’y est pas attaché.
PROBLÈMES DE FONCTIONNEMENT PROBLÈME CAUSE CORRECTION Fuite d’air au corps de valve de détente. . . . . . . . . Joints toriques coupés ou usés. . . . . . . . . . . . . . . . Remplacer les joints toriques . Fuite d’air à la tige de valve de détente. . . . . . . . . . Joints toriques ou garnitures coupés ou usés. . . . . Remplacer joints toriques /garnitures. Fuite d’air entre le corps et le nez. . . . . . . . . . . . . . Vis du nez desserrées. . . . . . . . . . . . . . . . . . . . . . .
DÉFLECTEUR D’ÉCHAPPEMENT DIRECTIONNEL Desserrer la vis comme indiqué. Régler en fonction de la direction d’échappement souhaitée, puis resserrer la vis.