FINISH TOOLS HERRAMIENTAS DE ACABADO OUTILS DE FINITION SB-150SX SB-125BN SB-1664FN SB-2IN1 SB-1842BN SB-1850BN OPERATION and MAINTENANCE MANUAL MANUAL DE OPERACIÓN Y DE MANTENIMIENTO MANUEL D’INSTRUCTIONS ET D’ENTRETIEN BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
INTRODUCTION The Bostitch SB Series are precision-built tools, designed for high speed, high volume nailing and stapling. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before operating the tool and understand the safety warnings and cautions.
SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
TOOL SPECIFICATIONS All screws and nuts are metric. MODEL TOOL ACTUATION SB-1842BN SB-1850BN SB-150SX SB-1664FN SB-125BN SB-2IN1 LENGTH HEIGHT WIDTH 9.25” 9.25” 9.50” 11.25” 9.25” 9.25” 8.5” 9.5” 8.75” 11.50” 8” 8.5” 2” 2” 2” 3” 2” 2” Sequential Trip Sequential Trip Sequential Trip Sequential Trip Sequential Trip Sequential Trip WEIGHT 2.38 2.69 2.65 4.03 2.12 2.38 lbs. lbs. lbs. lbs. lbs. lbs.
AIR SUPPLY AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses should have a minimum of 150 p.s.i. (10.6 kg/cm2) working pressure rating or 150 percent of the maximum pressure that could be produced in the air system.
LOADING THE SB-1842BN/SB-1850BN/SB-2IN1/SB-125BN EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
LOADING THE SB-150SX EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
LOADING THE SB-1664FN EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
TOOL OPERATION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must ensure that proper eye protection is worn.
TOOL OPERATION CHECK: CAUTION: Remove all fasteners from tool before performing tool operation check. 1. CONTACT TRIP OPERATION: A. With finger off the trigger, press the contact trip against the work surface. THE TOOL MUST NOT CYCLE. B. Hold the tool off the work surface, and pull the trigger. THE TOOL MUST NOT CYCLE. C. With the tool off the work surface, pull the trigger. Press the contact trip against the work surface. THE TOOL MUST CYCLE. D.
MAINTAINING THE PNEUMATIC TOOL When working on air tools, note the warnings in this manual and use extra care evaluating problem tools. CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand.
TROUBLE SHOOTING PROBLEM CAUSE Trigger valve housing leaks air Trigger valve stem leaks air Frame/nose leaks air O-ring cut or cracked . . . . . . . . . . . . . . .Replace O-ring O-ring/seals cut or cracked . . . . . . . . . .Replace trigger valve assembly Loose nose screws . . . . . . . . . . . . . . . .Tighten and recheck O-ring or Gasket is cut or cracked . . . . .Replace O-ring or gasket Bumper cracked/worn . . . . . . . . . . . . . .Replace bumper Damaged gasket or seal . . . . . . . . . . . .
DEPTH ADJUSTMENT Always disconnect air supply: 1. Before making adjustments; 2. When servicing the tool; 3. When clearing a jam; 4. When tool is not in use; 5. When moving to a different work area, as accidental actuation may occur, possibly causing injury. SB-1842BN, SB1850BN, SB-1664FN, SB-125BN FASTENER CONTROL ADJUSTMENT The Fastener Control adjustment feature provides close control of the fastener drive depth; from flush with the work surface to shallow or deep countersink.
ACCESSORIES AVAILABLE BC602 BC603 BC604 1 pint Bostitch Air -Tool Lubricant 1 pint Bostitch “Winter-Formula” Air-Tool Lubricant 1 quart Bostitch Air -Tool Lubricant -14-
INTRODUCCIÓN Las Bostitch SB Series son herramientas fabricadas con precisión diseñadas para trabajos de clavado y engrapado de alta velocidad y de gran volumen. Estas herramientas prestarán un servicio eficiente y fiable siempre y cuando se utilicen correctamente y con cuidado. Al igual que con cualquier herramienta automática de calidad, el mejor rendimiento se obtiene siguiendo las instrucciones del fabricante.
INSTRUCCIONES DE SEGURIDAD Cuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas que se encuentren en el área de trabajo, SIEMPRE deben usar PROTECCIÓN OCULAR que cumpla las especificaciones ANSI para resguardo contra partículas volantes arrojadas desde el FRENTE o los LATERALES. Dicha protección ocular se requiere para proteger contra residuos y remaches volantes, que podrían causar graves lesiones en los ojos.
MANTENIMIENTO DE LA HERRAMIENTA Tome nota de las advertencias en este manual al trabajar con herramientas neumáticas y tenga mayor cuidado al evaluar herramientas problemáticas. ESPECIFICACIONES DE LA HERRAMIENTA Todos las medidas de tornillos y tuercas son métricas. MODELO ACTIVACIÓN DE LA HERRAMIENTA LARGO ALTURA ANCHO SB-1842BN SB-1850BN SB-150SX SB-1664FN SB-125BN SB-2IN1 Disparo Disparo Disparo Disparo Disparo Disparo 9.25” 9.25” 9.50” 11.25” 9.25” 9.25” 8.5” 9.5” 8.75” 11.50” 8” 8.
SUMINISTRO DE AIRE Y CONEXIONES No use oxígeno, gases combustibles o gases embotellados como una fuente de suministro para esta herramienta, ya que la herramienta puede estallar, posiblemente causando lesiones. CONEXIONES: Instale un enchufe macho en la herramienta que fluya libre y que descargue la presión de aire de la herramienta cuando sea desconectada de la fuente de suministro.
CÓMO CARGAR LAS HERRAMIENTAS SB-1842BN/SB-1850BN/SB-2 IN1/SB-125BN PROTECCIÓN PARA LOS OJOS que cumple con las especificaciones de ANSI y que proporciona protección contra partículas voladoras tanto del FRENTE como del LADO debe ser usada SIEMPRE por el OPERADOR y otros en el área de trabajo al cargar, operar o hacerle servicio a esta herramienta. La protección para los ojos es necesaria para proteger contra sujetadores voladores y escombros que pueden causar daños severos a los ojos.
CÓMO CARGAR EL SB-150SX PROTECCIÓN PARA LOS OJOS que cumple con las especificaciones de ANSI y que proporciona protección contra partículas voladoras tanto del FRENTE como del LADO debe ser usada SIEMPRE por el OPERADOR y otros en el área de trabajo al cargar, operar o hacerle servicio a esta herramienta. La protección para los ojos es necesaria para proteger contra sujetadores voladores y escombros que pueden causar daños severos a los ojos.
CÓMO CARGAR EL SB-1664FN PROTECCIÓN PARA LOS OJOS que cumple con las especificaciones de ANSI y que proporciona protección contra partículas voladoras tanto del FRENTE como del LADO debe ser usada SIEMPRE por el OPERADOR y otros en el área de trabajo al cargar, operar o hacerle servicio a esta herramienta. La protección para los ojos es necesaria para proteger contra sujetadores voladores y escombros que pueden causar daños severos a los ojos.
OPERACIÓN DE LA HERRAMIENTA PROTECCIÓN PARA LOS OJOS que cumple con las especificaciones de ANSI y que proporciona protección contra partículas voladoras tanto del FRENTE como del LADO debe ser usada SIEMPRE por el OPERADOR y otros en el área de trabajo al cargar, operar o hacerle servicio a esta herramienta. La protección para los ojos es necesaria para proteger contra sujetadores voladores y escombros que pueden causar daños severos a los ojos.
VERIFICACIÓN DE LA OPERACIÓN DE LA HERRAMIENTA: ¡PRECAUCIÓN: QUITE TODOS LOS SUJETADORES DE LA HERRAMIENTA ANTES DE EFECTUAR LA VERIFICACIÓN DE LA OPERACIÓN DE LA HERRAMIENTA! 1. OPERACIÓN DE DISPARO POR CONTACTO: A. Apriete el disparador de contacto contra la superficie de trabajo, sin tocar el gatillo. LA HERRAMIENTA NO DEBE EFECTUAR SU CICLO. B. Sostenga la herramienta alejada de la superficie de trabajo, y hale el gatillo. LA HERRAMIENTA NO DEBE EFECTUAR SU CICLO. C.
MANTENIMIENTO DE LA HERRAMIENTA NEUMÁTICA Al trabajar con herramientas neumáticas, tenga presente las advertencias que se hacen en este manual, y sea particularmente cuidadoso al evaluar herramientas problemáticas. PRECAUCIÓN: El resorte de empuje (resorte de fuerza constante): Se debe tener cuidado al trabajar con el ensamblaje de resorte. El resorte está enrollado alrededor de, pero no sujetado a, un enrollador.
DIAGNÓSTICO DE FALLA PROBLEMA CAUSA CORRECCIÓN Fuga de aire en la envoltura de la Anillo en O cortado o rajado Reemplazar el anillo en O. válvula disparadora. Vástago de la válvula disparadora Anillos en O/sellos cortados o rajados. Reemplazar anillo en O/sellos. Tornillos de nariz flojos. Apriete y verifique nuevamente. tiene fuga de aire. Fuga de aire en el armazón/nariz. Fuga de aire en el armazón/tapón. No desempeña su ciclo.
Siempre desconecte el suministro de aire: 1. antes de efectuar ajustes; 2. al dar servicio a la herramienta; 3. al eliminar un atascamiento; 4. cuando la herramienta no se usa; 5. al trasladarse a otra área de trabajo, para que no se active accidentalmente, posiblemente causando una lesión.
INTRODUCTION Les outils SB Série de Bostitch sont construits avec précision et conçus pour réaliser un travail rapide à débit maximum de clouage et agrafage. Ces outils sont faits pour assurer un service efficace et durable, à condition d’être utilisés avec précaution et selon des conditions normales d’utilisation. Comme pour tout appareil, les consignes du fabricant doivent être impérativement suivies, afin d’obtenir une bonne performance.
CONSIGNES DE SÉCURITÉ UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’AVANT et des CÔTÉS, doit toujours être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement au réseau d’air, du chargement, du fonctionnement et de la maintenance de l’outil.
ENTRETIEN DE L’APPAREIL Lors de l’utilisation d’un outil fonctionnant sous-pression, lire les avertissements du manuel et user d’extrêmes précautions lors de la découverte d’un problème. CARACTÉRISTIQUES DE L’APPAREIL Toutes les mesures des vis et des boulons sont dans le système métrique.
ALIMENTATION EN AIR COMPRIMÉ ET RACCORDEMENT L’oxygène, les gaz combustibles ou les bouteilles de gaz ne doivent en aucun cas être employés comme source d’énergie, car ils peuvent exploser et provoquer des blessures. RACCORDEMENTS : Installer le raccord mâle sur l’appareil. Lors du désaccouplement de la source d’énergie, le raccord mâle doit permettre rapidement la mise à l’atmosphère de toute pression résiduelle.
CHARGEMENT DES SB-1842BN/SB-1850BN/ SB2IN1/SB-125BN PROTECTION DES YEUX : Elle doit répondre aux spécifications ANSI et offrir une protection contre les particules projetées, à la fois FRONTALE et LATÉRALE. Cette protection devra TOUJOURS être portée par l’opérateur et les autres membres du personnel qui travaillent dans le lieu de chargement, de fonctionnement et d’entretien de l’appareil.
CHARGEMENT DU SB-150SX PROTECTION DES YEUX : Elle doit répondre aux spécifications ANSI et offrir une protection contre les particules projetées, à la fois FRONTALE et LATÉRALE. Cette protection devra TOUJOURS être portée par l’opérateur et les autres membres du personnel qui travaillent dans le lieu de chargement, de fonctionnement et d’entretien de l’appareil.
CHARGEMENT DU SB-1664FN PROTECTION DES YEUX : Elle doit répondre aux spécifications ANSI et offrir une protection contre les particules projetées, à la fois FRONTALE et LATÉRALE. Cette protection devra TOUJOURS être portée par l’opérateur et les autres membres du personnel qui travaillent dans le lieu de chargement, de fonctionnement et d’entretien de l’appareil.
FONCTIONNEMENT DE L’APPAREIL PROTECTION DES YEUX : Elle doit répondre aux spécifications ANSI et offrir une protection contre les particules projetées, à la fois FRONTALE et LATÉRALE. Cette protection devra TOUJOURS être portée par l’opérateur et les autres membres du personnel qui travaillent dans le lieu de chargement, de fonctionnement et d’entretien de l’appareil.
VÉRIFICATION DU SYSTÈME DE DÉCLENCHEMENT ATTENTION : retirer toutes les attaches de fixation de l’outil avant de procéder à une vérification du fonctionnement de celui-ci. 1. SYSTÈME DE SÉCURITÉ À LA VOLÉE (C.T.): A. Enfoncer l’élément palpeur sur la surface de travail sans actionner la détente. L’APPAREIL NE DOIT PAS SE DÉCLENCHER B. Éloigner l’appareil de la surface de travail et appuyer sur la détente. L’APPAREIL NE DOIT PAS SE DÉCLENCHER C.
ENTRETIEN DE L’APPAREIL Lors de l’utilisation d’un outil fonctionnant sous-pression, lire les avertissements du manuel et user d’extrêmes précautions lors de la découverte d’un problème. ATTENTION : Ressort-poussoir (ressort à poussée constante). Il est recommandé d’user de prudence lors de la manipulation du système du ressort. Le ressort est enroulé autour du rouleau mais n’y est pas attaché.
PROBLÈMES DE FONCTIONNEMENT PROBLÈME CAUSE CORRECTION Fuite d’air au corps de valve de détente. . . . . . . . Joints toriques coupés ou usés. . . . . . . . . . . . . . . . . Remplacer les joints toriques . Fuite d’air à la tige de valve de détente. . . . . . . . Joints toriques ou garnitures coupés ou usés. . . . . . Remplacer joints toriques /garnitures. Fuite d’air entre le corps et le nez. . . . . . . . . . . . . Vis du nez desserrées. . . . . . . . . . . . . . . . . . . . . . . .
Toujours désaccoupler l’appareil de sa source d’énergie : 1) avant tout réglage; 2) lors de l’entretien; 3) lors du désenrayage; 4) à la fin de l’utilisation; 5) lors du déplacement vers une nouvelle zone de travail, car un déclenchement accidentel peut se produire et causer des blessures.