System8000 Micro Reference Series 6-Piece Speaker System with PowerVent® Powered Subwoofer
Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Specifications System Frequency Response (±3dB) 44–20,000Hz Recommended Amplifier Power 15–125 watts Nominal Impedance 8 ohms Sensitivity (1 watt [2.83v] at 1m) 89dB Subwoofer Amplifier Power 65 watts continuous 4Ω; < 0.
How to Wire Your Speakers You need to wire your speakers correctly to obtain the best sound quality and the proper image. Wiring should just take a few minutes, but it’s important to do it carefully, since incorrect wiring (such as reversed connections) can result in a poor soundstage or poor bass. We recommend using 18-gauge or larger speaker wire for runs up to 25 feet (8m), and thicker 16-gauge or larger for longer runs.
Connecting the System8000 Speaker-Level Connections The simplest way to wire the Micro80p is via speaker connections. Wired in this way, the subwoofer (Micro80pv) does not present any additional load to your amplifier. There are three ways to wire the subwoofer to your speaker connections; each way produces the same result. You may want to use long wires to the subwoofer at first, so you may experiment with placement.
Connecting the System8000 (cont.) Speaker-Level Connections (cont.) Option 1: Connect the Receiver speaker terminals on the Micro80pv Subwoofer Micro80pv to the left and Line in right speaker outputs of your receiver. Use the Left Surround speakers Right Center speaker Left Main speakers Right same speaker outputs L R Speaker level in that drive the Micro80x satellites. Do not connect the Micro80pv to any other speaker outputs that may be on Left Micro80e Right Micro80e your receiver.
Connecting the System8000 (cont.) Speaker-Level Connections (cont.) Alternative options (cont.): In some cases, you may find it easier to use one of the following alternative wiring plans. The resulting sound will be the same. Micro80pv Subwoofer Receiver Option 3: Connect the speaker terminals Line in Speaker level in L R on the Micro80pv to the terminals on the Left Surround speakers Right Center speaker Left Main speakers Right Micro80x satellites.
Dolby Pro Logic and Dolby Digital Line-Level System Connection Using the line-level connection to the Micro80pv subwoofer generally results in a cleaner system sound, since the receiver no longer has to reproduce the difficult low bass information that can push it into audible distortion (also known as clipping). Dolby Pro Logic Systems Use an RCA cable (not included) to connect your receiver’s Sub out jack to the Line in jack on the Micro80pv, as shown below.
Dolby Pro Logic and Dolby Digital Line-Level System Connection (cont.) Dolby Digital Systems If your receiver or processor gives you a choice of subwoofer low-pass crossover settings, select one around 120Hz. This will result in the smoothest overall system response, since the lower response limit of the Micro80x satellite and Micro80c center channel is 120Hz. Select “SMALL” for the front left/right speakers, the center channel speaker, and the surround speakers on your receiver’s set-up menu.
Micro80pv Subwoofer Controls Volume: Adjusts the sound level of the subwoofer. If you are using the speaker-level connections, begin with a setting at about the 10:00 o’clock position. When using the line-level connections, begin with a setting around 11:00 o’clock. Your actual setting may vary due to personal taste, program material, and subwoofer placement. NOTE: Power is always supplied to the subwoofer electronics unless it is unplugged.
How to Place Your Speakers Room placement is one of the most important factors Center channel flush with front of TV for sound quality. Taking a few minutes to try differ- Left satellite 1-3 ft. (0.3-1m) Right satellite 1-3 ft. (0.3-1m) Subwoofer in corner for maximum bass output ent placements ensures that your speakers will Place the surround speakers beside or behind the listeners, above ear level sound best in your listening environment. 5-9 ft. (1.
Wall-Mounting the Micro80e Effects Speakers Drill two 7⁄ 16" (11mm) holes for toggle wings. If mounting on a 1 surface other than drywall, consult a knowledgeable installer about the proper hardware to use on your wall. If you are running speaker wire behind the wall, drill a 1⁄ 2" 2 (12mm) hole 3⁄ 4" (19mm) below the top toggle wing hole. Attach bracket to wall with machine screws and toggle wings, 3 as shown below. 4 Connect speaker wire to speaker.
Wall-Mounting the Micro80e Effects Speakers (cont.) #9 x 1" wood screws 2 3 1" (25mm) 25/32" (55mm) 1 flathead machine screw 5 4 1 Attach bracket to speaker with flathead machine screw. 2 Drill two 1⁄ 8" (3mm) pilot holes for wood screws, then mount screws. Leave about 1⁄ 8" (3mm) of screw thread exposed. If mounting on drywall, use plastic anchors (not included). Consult a knowledgeable installer about the proper hardware to use on your wall.
Setting Up Your Home Theater System Volume Levels: To obtain the best home theater effect, match the sound levels of each speaker. Home theater systems include a test signal that simplifies this level matching. Refer to the instructions provided with your surround-sound electronics. Center Channel Mode: Generally, with all surround systems, including Dolby® Pro Logic® and Dolby® Digital, the center channel mode should be set to “NORMAL” or “SMALL.
Wall-Mounting Your Micro80x Satellites The Micro80x satellite may be wall-mounted using the included keyhole bracket: 1 Install a #8 or #10 mounting screw on the wall (not supplied–consult a knowledgeable installer regarding the proper 1 hardware to use on your wall surface). 2 Attach the bracket to the back of the speaker with the machine screw and acorn nut as shown. 3 If you are running wires behind the 3 wall, make a 3⁄ 8" (9.5mm) wire hole, 13⁄4" (44mm) below the mounting screw for the wire.
Limited Warranty For five years from the date of purchase, Boston Acoustics will repair for the original owner any defect in materials or workmanship that occurs in the normal use of the Micro80x satellites, Micro80c center channel speaker, and Micro80e effects speakers, without charge for parts and labor.